Target Howell FCS60615ST User manual

Howell
upholstered small space chat set
style # FCS60615ST
dpci # 009003842
>>assembly instructions TM

Congratulations on your latest Target purchase.
Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.
Good luck – though we're confident you won't need it.
ATTENTION:
These Chairs and Side Table are not intended for use during any kind of inclement weather and the manufacturer
is not and can not be held responsible for any damages caused as a result of such weather. Weather-related
damage, or damage as a result of the Chair and Side Table not being stored properly when not in use is not the
responsibility of the manufacturer.
During extended periods of non-usage, off season, or in inclement weather (wind, rain, snow, hail,
sleet), freezing conditions and extreme heat, the Chair and Side Table need to be stored in a dry sheltered place to
prolong the life and to avoid damage to the Chair and Side Table.
2
IMPORTANT WARNING:
Unpack the box on a clean soft level surface and make sure all parts have been included.
To replace missing or damaged parts please call 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.

otrio 2020
3
WARRANTY:
These Chairs and Side Table come with a one year limited warranty against original manufacture defects. If you experience
trouble with your new chair and side table, please call the customer service number below.
before you begin
1. Check for damage or missing parts. Call 855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
Target Corporation
Toll Free at: 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
Code: Y

table of contents
introduction
hardware
parts list
assembly
2-3
5
6
7-12
QUESTIONS?
4Please call 855-MYTGTHOME (855-698-4846) parts and service. For faster service, have th e style number and DPCI number ready when calling.

hardware
5
(Part G)×4
M6*20mm bolt with washer
(Part H)×8
M6*30mm bolt with washer
(Part J)×1
allen wrench
(Part I)×12
M6*15mm bolt with washer
ATTENTION: THE HARDWARE KIT IS FOR 1 SET.

ITEM DESCRIPTION QUANTITY
2
A
6
right armrest
Bleft armrest 2
Cchair seat
Dchair back
2
2
A
D
B
C
E table top
F table leg
1
4
E
F

7
step 01:
(Part H)×2
M6*30mm bolt with washer
(Part J)×1
allen wrench
ATTENTION: To avoid damage to your new patio furniture, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
1. Attach the chair seat (C) to the right armrest (A) by lining up the bolt holes on the end of
the chair seat (C) with the corresponding bolt holes on the right armrest (A).
2. Secure with M6*30mm bolt with washer (H) using allen wrench (J).
Do not completely tighten screws until all screws are in place.
C
A
H

8
step 02:
(Part G)×1
M6*20mm bolt with washer
(Part J)×1
allen wrench
1. Attach the chair back (D) to the right armrest (A) by lining up the bolt holes on the end of
the chair back (D) with the corresponding bolt holes on the right armrest (A).
2. Secure with M6*20mm bolt with washer (G) using allen wrench (J).
Do not completely tighten screws until all screws are in place.
A
D
G
1. 2.

9
step 03:
(Part H)×2
M6*30mm bolt with washer
(Part J)×1
allen wrench
1. Attach the left armrest (B) to the chair seat (C) and chair back (D) by lining up the bolt holes
on the end of the chair seat (C) and chair back (D) with the corresponding bolt holes on the
left armrest (B).
2. Secure with M6*20mm bolt with washer (G) and M6*30mm bolt with washer (H) using allen wrench (J).
Do not completely tighten screws until all screws are in place.
1. 2. 3.
C
D
B
H
G
(Part G)×1
M6*20mm bolt with washer
3. Repeat above steps for other chair.

step 04
10
2. Turn the chair to upright position onto a flat level surface.
Put the cushion on the chair.
You are now ready to enjoy your new chair.
1. Tighten all the bolts. Please lift the chair back up when
tightening the bolts.

11
step 05:
(Part I)×12
M6*15mm bolt with washer
(Part J)×1
allen wrench
1. Attach the table leg (F) to the table top (E) by lining up the bolt holes on the
table top (E) with the corresponding bolt holes on the table leg (F).
2. Secure with M6*15mm bolt with washer (I) using allen wrench (J).
Do not completely tighten screws until all screws are in place.
F
E
I I
3. Repeat above step until the 4 table legs (F) are secured to the table top (E).

step 06
12
1. Tighten all the bolts.
2. Turn the table to upright position onto a flat level surface.
You are now ready to enjoy your new table.

13

TM
2020 Target. The Bullseye Design is a trademark of Target Brands Inc. All rights reserved.