Target fairglen TGFGBENCWH User manual

>>
fairglen
entryway bench
assembly instructions
style # TGFGBENCWH (white)
dpci # 249-18-0648
tcin # 54158332
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-13
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 12
wooden dowel
(H2) x 8
cam bolt
(H3) x 8
cam
(H4) x 17
pan head screw
(H5) x 4
shelf support
(H6) x 4
washer
(H7) x 4
lock washer
(H8) x 4
bolt
(H9) x 1
allen wrench

5
exploded diagram
ITEM DESCRIPTION QUANTITY
A top panel 1
B left side panel 1
C right side panel 1
D partition 1
E adjustable shelf 1
F bottom panel 1
G back panel 1
H sliding door 1
I center leg 1
J cushion 1

6
how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
1. 2. 3.
4.4. 5.5.

7
step 1: attach top panel and bottom panel to partition
(H1) x 4
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
1.1. Carefully tap small wooden dowels into place in top panel and bottom panel. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush in top panel and bottom panel.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.

8
step 2: attach center leg
2.1. Align center leg with pre-drilled hole to attach to bottom panel.

9
step 3: attach right side panel
(H1) x 4
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
(H6) x 2
washer
(H7) x 2
lock washer
(H8) x 2
bolt
(H9) x 1
allen wrench
3.1. Carefully tap small wooden dowels into place in right side panel. Leave 1/2” of the dowels sticking out.
3.2. Align bolts with pre-drilled holes to attach top panel to right side panel. Do not over tighten bolts.
3.3. Screw-In cam bolts must be screwed down ush in right side panel.
3.4. Refer to page 6 for instructions on how to use the cam lock system.
3.5. Do not over tighten bolts.

10
step 4: install sliding door
4.1. Insert sliding door into tracks located on top panel and bottom panel.

11
step 5: attach left side panel
(H1) x 4
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
(H6) x 2
washer
(H7) x 2
lock washer
(H8) x 2
bolt
(H9) x 1
allen wrench
5.1. Carefully tap small wooden dowels into place in left side panel. Leave 1/2” of the dowels sticking out.
5.2. Align bolts with pre-drilled holes to attach top panel to left side panel. Do not over tighten bolts.
5.3. Screw-In cam bolts must be screwed down ush in left side panel.
5.4. Refer to page 6 for instructions on how to use the cam lock system.
5.5. Do not over tighten bolts.

12
step 6: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN DOOR NOT SLIDING SMOOTHLY**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 17
pan head screw
6.1. Make sure the pan head screws go through the pre-drilled holes properly to attach back panel. Do not over tighten screws.

step 7: install adjustable shelf and cushion
(H5) x 4
shelf support
7.1. Insert shelf supports into desired hole. Different holes accommodate different shelf heights.
7.2. Angle shelf to fit between the rails and set on top of shelf supports.
7.3 Place cushion on top of bench.
13
nished edge
Insert shelf supports into desired hole. Di󰀨erent holes accommodate di󰀨erent shelf heights.
Angle shelf to t between the rails and set on top of shelf supports.

14
1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in
excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury.
2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
adjustable leg levelers
25 lbs. per shelf
250 lbs.

© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.