Target PROJECT 62 TGTD54-1 User manual

>> Assembly instructions
TM
© 2021 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
ADA Large Desk
Style #: TGTD54-1
DPC-item #: 249-14-0270

Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Good luck – though we’re confident you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a work surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed (only hex wrench included)
For tipping restraint hardware kit only.
Phillips
screwdriver
Hex wrench
2

hardware
(H1) x 16
1/4” x 13mm bolt
(H2) x 6
1/4” x 30mm bolt
(H3) x 18
M4 x 12mm
pan head screw
(H4) x 1
hex wrench
(H5) x 1
tipping restraint hardware kit
(inside plasticbag)
Spare hardware
3

exploded diagram
A
B
C
D
E
F
F
G
G
H
ITEM DESCRIPTION QTY
ATop panel 1
BLeft side frame 1
CRight side frame 1
DDrawer box 1
EBack upper stretcher 1
FDrawer box support 2
GBack side brace 2
HBack bottom stretcher 1
ITop stretcher 2
JDesk top support 2
4
I
I
J
J

step 1: attach the back stretchers to the right side frame
5
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
(H1) x 2
1/4” x 13mm bolt
(H4) x 1
hex wrench
1.1. Orient and fit the back upper stretcher (E) onto the U-shaped bracket on the right side frame (C) and secure them with one 13mm bolt (H1).
1.2. Fasten the back bottom stretcher (H) to the bottom U-shaped bracket on the right side frame (C) with one 13mm bolt (H1).
E
H
C
H
C
H
H1
The threaded holes for drawer box
supports face the front of the unit.
C

step 2: attach the top stretchers to the right side frame
6
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
I
I
C
I
C
I
C
(H1) x 2
1/4” x 13mm bolt
(H4) x 1
hex wrench
The metal tabs are located at the
bottom and face inward.
H1
2.1. Orient and fit two top stretchers (I) onto the U-shaped brackets on the right side frame (C) and secure them into place with two 13mm bolts (H1).

step 3: attach the left side frame to the previous assembly
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
7
B
I
I
E
H
H
BB
H
(H1) x 4
1/4” x 13mm bolt
(H4) x 1
hex wrench
3.1. Repeat the same procedure to attach the left side frame (B) to the previous assembly with four 13mm bolts (H1).

step 4: attach the desk top supports to the top panel
4.1. Using the pilot holes as a guide, attach two desk top supports (J) to the top panel (A) with eight 12mm pan head screws (H3).
(H3) x 8
M4 x 12mm
pan head screw
NOTE: DO NOT use power tools.
J
A
H3
H3
A
J
J
8

5.1. Orient and attach the top panel (A) between the top stretchers (I) and side frames (B and C) with ten 12mm screws (H3).
step 5: attach the top panel to the previous assembly
(H3) x 10
M4 x 12mm
pan head screw
A
I
I
B
C
H3
CBI
/ /
A
The top supports are located
at front of the unit.
NOTE: Try working from one end to
the other to slide the top panel (A) into
place. You may need to push or pull
the top stretchers and side frames
slightly to get them to align with the
holes. DO NOT use power tools.
9

step 6: attach back side braces
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
10
(H1) x 4
1/4” x 13mm bolt
(H4) x 1
hex wrench
6.1. Align and attach two back side braces (G) between the side frames (B and C) and the back upper stretcher (E) with four 13mm bolts (H1).
G
C
B/
H1 H1
E
B
C
G
G
E