Target Windham User manual

windham
large media cabinet
assembly instructions
style # WNLGMDIABK (black)
dpci # 249-10-0470
style # WNLGMDIABL (teal)
dpci # 249-10-0471
style # WNLGMDIAWH (shell)
dpci # 249-10-0472
style # WNLGMDIANV (navy)
dpci # 249-10-0395
style # WNLGMDIAGG (green garnish)
dpci # 249-10-0923
style # WNLGMDIAOV (overcast)
dpci # 249-10-0924
style # WNLGMDIABN (banana split)
dpci # 249-10-0925
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
>>

Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed
2QUESTIONS? Just call 1-855-MYTGTHOME (1-855-698-4846) for service. For faster service, have the style number and dpci number ready when calling.

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-14
QUESTIONS? Just call 1-855-MYTGTHOME (1-855-698-4846) for service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 16
wooden dowel
(H2) x 4
25mm at head screw
(H3) x 12
cam bolt
(H4) x 12
cam
(H5) x 29
15mm pan head screw
(H6) x 8
12mm at head screw
(H7) x 2
knob
(H8) x 2
knob bolt
(H9) x 16
shelf support
(H10) x 2
magnet
(H11) x 1
19mm truss head screw
(H12) x 1
wall strap
(H13) x 1
wall anchor
(H14) x 1
38mm wall screw
(H15) x 2
5/8” washer

5
exploded diagram
ITEM DESCRIPTION QUANTITY
A top panel 1
B left side panel 1
C right side panel 1
D partition 2
E bottom panel 1
F back panel 1
G left door 1
H right door 1
I outer adjustable shelf 2
J inner adjustable shelf 2
K foot 2

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
2.
6
4. 5.
1. 3.

7
step 1: attach partition panels to bottom panel
(H1) x 4
wooden dowel
(H3) x 4
cam bolt
(H4) x 4
cam
1.1. Carefully tap small wooden dowels into place in bottom panel. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush in bottom panel.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.

8
step 2: attach center feet to bottom panel
2.1. Align feet with pre-drilled holes.
2.2. Do not over tighten feet.

9
step 3: attach side frames
(H1) x 4
wooden dowel
(H3) x 4
cam bolt
(H4) x 4
cam
3.1. Carefully tap small wooden dowels into place in left side panel and right side panel. Leave 1/2” of the dowels sticking out.
3.2. Screw-In cam bolts must be screwed down ush in left side panel and right side panel.
3.3. Refer to page 6 for instructions on how to use the cam lock system.
3.4. Do not over tighten bolts.

step 4: attach top panel
(H1) x 8
wooden dowel
(H10) x 2
magnet
(H5) x 4
15mm pan head screw
(H3) x 4
cam bolt
(H4) x 4
cam
(H2) x 4
25mm at head screw
4.1. Carefully tap small wooden dowels into place in top panel. Leave 1/2” of the dowels sticking out.
4.2. Screw-In cam bolts must be screwed down ush in top panel.
4.3. Refer to page 6 for instructions on how to use the cam lock system.
4.4. Do not over tighten bolts.
10
H5
H5

11
step 5: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN DOOR NOT SLIDING SMOOTHLY**
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H5) x 25
15mm pan head screw
5.1. Make sure the screws go through the pre-drilled holes properly.
5.2. Do not over tighten screws.
hole for anti-tip

12
step 6: attach doors to side frames
(H6) x 8
12mm at head screw
(H7) x 2
knob
(H8) x 2
knob bolt
6.1. Align screws with pre-drilled holes.
6.2. Align bolts with pre-drilled holes.
6.3. Do not over tighten screws or bolts.

13
step 7: install adjustable shelves
(H9) x 16
shelf support
7.1. Insert shelf supports into desired hole. Di󰀨erent holes accommodate di󰀨erent shelf heights.
7.2. Angle shelf to t between the rails and set on top of shelf supports.

step 8: install anti-tip kit
(H11) x 1
19mm truss head screw
(H12) x 1
wall strap
(H15) x 2
5/8” washer
(H13) x 1
wall anchor
(H14) x 1
38mm wall screw
Position against wall
Mark position of strap hole on
wall
Drill 1/4’’ hole
Tap in wall anchor
Fasten anti-tip strap
with at-head screw provided
14
(H12)
(H15)
(H11)
(H14) (H15)
(H13)
QUESTIONS? Just call 1-855-MYTGTHOME (1-855-698-4846) for service. For faster service, have the style number and DPCI number ready when calling.


15

  
 

    
   
    
  

  

      
(OR)
     

   
 
 
WARNING
For use with televisions weighing 94
pounds (42.6 kg) or less. Use with
heavier televisions may result in
instability causing tip over resulting
in death or serious injury.
Use of anti-tip restraints may only
reduce, but not eliminate, the risk
of tip-over.
Manufactured by: BDDMI
Factory #: 16840041
1. WARNING - Death or serious injury may occur when children climb on
audio and/or video equipment furniture. A remote control or toys placed
on the furnishing may encourage a child to climb on the furnishing and as a
result the furnishing may tip over on to the child.
2. WARNING - Relocating audio and/or video equipment to furniture not
specically designed to support audio and/or video equipment may result
in death or serious injury due to the furnishing collapsing or over turning
onto a child.
3. This unit has been designed for the weight shown. Exceeding this recom-
mended weight could result in excessive “sagging” of the top. Extreme
overloading can cause failure of the top and possible injury.
4. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray
furniture polish as needed.
!
QUESTIONS?
Just call 1-855-MYTGTHOME (1-855-698-4846) for service. For faster service, have the style number and DPCI number ready when calling.
holds at panel TVs
up to 55’’ or 94 lbs.
interior shelf capacity 40 lbs.

© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.