Tecnosicurezza DigiTech Series User manual

DigiTech
Installation instructions

2 of 20 II_ DigiTech_01_eng
Installation instructions
DigiTech
Company
Founded in 1983 with the aim of providing a complete range of professional products,
Tecnosicurezza is now a consolidated reality in the field of locks and security systems for safes.
The experience gained in over 35 years of activity in the security sector has allowed the
designing and manufacturing of high technology and reliability systems, which continue to
receive the approval of an increasingly demanding clientele.
TECNOSICUREZZA is present directly on the Italian, Spanish and US markets and, through a
extensive distribution network, in many European and extra-European countries.
TECNOSICUREZZA is aimed at national and international customers of primary importance, such
as banks, safe manufacturers, cash in transit companies, mass market retailers and post offices.
Today TECNOSICUREZZA is a leading company focused on the customers’needs and
constantly in step with technology.

II_DigiTech_01_eng 3 of 20
Installation instructions
DigiTech
Table of contents
COMPANY 2
TABLE OF CONTENTS 3
MODELS AND CHARACTERISTICS 4
ACCESSORIES 4
AUDIT AND PROGRAMMING ACCESSORIES 4
CERTIFICAZIONS 5
IMPORTANT NOTES! 6
KEYPAD DIMENSIONS 7
ROTOBOLT LOCK DIMENSIONS 8
STRAIGHTBOLT LOCK DIMENSIONS 8
SPRINGBOLT LOCK DIMENSIONS 9
MOTORLOCK DIMENSIONS 9
MOTORSPRINGBOLT LOCK DIMENSIONS 9
FIXED KEYPAD INSTALLATION INSTRUCTIONS 10
ROTOBOLT LOCK INSTALLATION INSTRUCTIONS 10
STRAIGHTBOLT AND SPRINGBOLT LOCKS INSTALLATION INSTRUCTIONS 11
MOTORLOCK AND MOTOR SPRINGBOLT LOCKS INSTALLATION INSTRUCTIONS 12
FUNCTIONAL TEST 14
CE DECLARATIONS 15
NOTES 17
CONTACTS 20

4 of 20 II_ DigiTech_01_eng
Installation instructions
DigiTech
Models and characteristics
Model
Variant
T9510/BR –Keypad in metal. Black colour
with rubber membrane foil keypad in black
colour.
/DL with Dallas key reader.
Accessories
Code
Description
N077/A
Battery box with alarm interface.
L4001
Large battery box for 6 size C 1.5V batteries.
T6005/W
Power supply interface (12Vdc).
T6005
Power supply interface (12Vdc) with alarm
interface.
L2666
Knob with 6 mm square spindle.
N1982
User Dallas key.
Audit and programming accessories
Code
Description
N42180/T
Interfaccia USB.
N42170/D
Dallas key reader with molex connector.
N42170/J
Dallas key reader with jack connector.
N42170/M
Magnetic Dallas key connection cable.
N1996RM
Magnetic Dallas key for audit.
T42146/J
Setup and audit cable.

II_DigiTech_01_eng 5 of 20
Installation instructions
DigiTech
Certificazions

6 of 20 II_ DigiTech_01_eng
Installation instructions
DigiTech
Important notes!
Before installing this product, please read carefully the installation and operating
instructions.
Locks can be installed in all traditional safes.
Lock has to be mounted on secure storage metal (preferred steel) units only.
Locks must be protected against external attacks, for this reason it is recommended to
install them on the door away from any through holes.
Any electronic part must be properly protected and not easily accessible even when
the door is open.
Locks have been developed to work correctly in a temperature range from -5 ° C to + 50
° C and in an environment with non-condensing humidity between 25% and 90%.
The mounting dimensions are standard (magic module).
For the installation of the keypad and lock, use only the screws provided by
Tecnosicurezza. Any other screw must be approved in advance.
Locks are supplied with metric (M6) mounting screws. Upon request, Imperial 1/4-20 UNC
format mounting screws are available.
The type of material and the length of the screws must, in any case, be selected so as to
guarantee long life and reliability.
Tighten the screws so that the lock is firmly fixed to the mounting surface
(recommended torque between 2.5 and 5.5 Nm).
The mounting surface must be perfectly flat.
In order to prevent loosening of the screws it is recommended the use of LOCTITE®
threadlocker and/or specific washers positioned under the head of the fixing screw.
The diameter of the passage hole for the connection cable or the spindle must not
exceed 11 mm.
The hole must be completely cleaned of drill dust and no edge should be sharp.

II_DigiTech_01_eng 7 of 20
Installation instructions
DigiTech
Lock must not be lubricated.
In the locked position, the distance between the bolt and the boltwork part that is
moving the lock bolt must comply with the following specifications for each type of lock.
Any component to be fixed to the lock bolt must be previously approved by Tecnosicurezza
before installation. In any case, the maximum load must not exceed 2.5 N.
Secure the cables away from moving parts by using cable ties and cable ties bases.
If placed in normal domestic or office environments, the locks do not require particular
maintenance; in any case, after 10,000 opening/closing cycles, it is recommended to run
a test that verifies the correct and complete operation of the product.
Use only DURACELL™ 9 Volt Alkaline batteries, or battery holders with DURACELL™ 1.5
Volt Alkaline batteries. Alternatively, it is also possible to use a stabilized 12V - 1A power
supply (p.n. N1212) with relative power supply interface (p.n. T6005/W or p.n. T6005).
A series of acoustic signals during opening indicate a low battery level. In this case, the
battery must be replaced.
Keypad dimensions

8 of 20 II_ DigiTech_01_eng
Installation instructions
DigiTech
STANDARD mounting
VERTICAL mounting
RotoBolt lock dimensions
StraightBolt lock dimensions

II_DigiTech_01_eng 9 of 20
Installation instructions
DigiTech
SpringBolt lock dimensions
MotorLock dimensions
MotorSpringBolt lock dimensions

10 of 20 II_ DigiTech_01_eng
Installation instructions
DigiTech
Fixed keypad installation instructions
Insert the keypad cable inside the hole on the safe door and connect it to the lock connector
"ENT" (connector 1 in the case of a MotorLock or Motor SpringBolt lock). Lift the keypad
membrane and, making sure that the connection cable and the battery cable are not damaged
by the keypad case, fix the screws to the relative threaded holes on the safe door.
STANDARD mounting
VERTICAL mounting
The keypad can also be installed in a quick hooking/unhooking mode (vertical mounting).
Remove the release liner placed under the membrane
and apply the latter on the keypad case.
Connect a battery to the battery connector inside the
keypad battery compartment or, if provided, connect the
battery pack to the lock connector "BAT" (connector 2 in
the case of a MotorLock or Motor SpringBolt lock).
RotoBolt lock installation instructions
The RotoBolt lock is a swingbolt lock whose block is carried out by a motor; it can be installed in
all 4 directions, even upside down.
By entering a valid code, the lock electronic removes the blocking for 3 seconds and the
boltwork can be moved into open position by pushing the bolt inside the lock case.
The bolt automatically secures when the safe handle, or the safe door mechanism, is brought
to the locked position.
If the RotoBolt lock is used in conjunction with other locks, the safe door mechanism must
ensure the closure of the RotoBolt before the other locks.
The lock can be mounted in all four mounting directions (RH, LH, VU, VD).
Furthermore, by flipping over the lock, both locking directions can be realized (RH/LH).

II_DigiTech_01_eng 11 of 20
Installation instructions
DigiTech
The maximum load applicable to the bolt must not exceed 1KN. Contact Tecnosicurezza in case
of heavier loads.
Connect the keypad cable to the lock connector "ENT", making sure it is fully inserted and
locked.
Any alarm interface or battery holder will be connected to the lock connector “BAT”.
To remove the cable, bring the connector upwards and carefully pull it out.
StraightBolt and SpringBolt locks installation instructions
StraightBolt and SpringBolt locks are locks with, respectively, a dead bolt and a spring bolt,
whose block is carried out by a motor.
By entering a valid code, the lock electronic removes the blocking for 3 seconds and the
boltwork can be moved into open position by turning the spindle inserted in the lock.
The spindle can be connected to a knob, a handle or directly to the keypad if equipped with a
rotation kit. When the spindle is brought to the locked position, the bolt comes out ensuring
the lock is locked.
The StraightBolt and SpringBolt locks can be mounted in all four mounting directions.
In the locked position, there should be approximately 1 mm
clearance between the lock bolt and the cavity in the blocking
bar of the boltwork. The bolt must be able to move freely
without force being applied to it.
In open position, there should be
minimum 3mm and maximum 5 mm
clearance between the lock bolt and
the blocking bar of the boltwork.
The maximum load applicable to the bolt must not exceed 1KN. Contact Tecnosicurezza in case of
heavier loads.
The spring-latch version (SpringBolt) is specially designed to ensure self locking when the door
closes.
In the locked position the distance between the RotoBolt
bolt and the RotobBolt part that is moving the lock bolt
should be approximately 1 mm.
The bolt must be able to move freely without force
being applied to it.

12 of 20 II_ DigiTech_01_eng
Installation instructions
DigiTech
The spindle must be inserted between a minimum of 7 mm to a maximum of 12 mm inside the
lock.
WARNING: do not insert the spindle up to the lid of the lock, but leave some margin to allow the
movement of the cable and to prevent any damage.
Make sure the cable is fully inserted and locked in the groove of the spindle.
Remove any residues deriving from the cutting of the spindle that could damage the cable.
Insert the cable connector into the square hole present in the bottom of the lock and make it come
out from the opposite side.
MotorLock and Motor SpringBolt locks installation instructions
MotorLock and Motor SpringBolt locks are locks with, respectively, a motor driven dead bolt and
a motor driven spring bolt, whose block is carried out by a motor.
By entering a valid code, the motor retracts the bolt which remains in the open position for about
8 seconds and then automatically returns to the locked position.
If the manual relocking option is selected, the bolt closes by pressing and holding the button .
The distance between the SpringBolt lock and the locking edge must
be between a minimum of 3 mm and a maximum of 8 mm.
When locked, there must be a 0.5mm
gap between lock bolt and locking
surface.
Secure the cable, avoiding to stretch it too much, inside the specific
groove on the lock cover and fix the lock using the appropriate
mounting screws.
Connect the keypad cable to the lock connector "ENT", making sure it is fully inserted and locked.
Any alarm interface or battery holder will be connected to the lock connector “BAT”.
To remove the cable, bring the connector upwards and carefully pull it out.

II_DigiTech_01_eng 13 of 20
Installation instructions
DigiTech
In the locked position, there should be approximately 1 mm
clearance between the lock bolt and the cavity in
the blocking bar of the boltwork. The bolt must be
able to move freely without force being applied to
it.
In open position, there should be
minimum 3mm and maximum 5 mm
clearance between the lock bolt and
the blocking bar of the boltwork.
The spring-latch version ( Motor SpringBolt) is specially designed to ensure self locking when
the door closes.
The distance between the SpringBolt lock and the locking edge must be
between a minimum of 3 mm and a maximum of 8 mm.
In open position, there should be
minimum 3mm and maximum 5 mm
clearance between the lock bolt and
the blocking bar of the boltwork.
Connect the keypad cable to the lock connector "1", making sure it
is fully inserted and locked.
Any alarm interface or battery holder will be connected to the lock
connector “2”.
To remove the cable, bring the connector upwards and carefully pull
it out.

14 of 20 II_ DigiTech_01_eng
Installation instructions
DigiTech
Functional test
To be carried out with the door open.
MEMBRANE TEST:
Press and hold the button 5 to access the "Membrane Test" function.
Press slowly all the buttons according to the sequence shown on the display.
ELECTRONIC / MECHANICAL TEST:
OPENING:
Enter the opening code (standard manager code 123456 or simply 1 if the lock is in pre-setup
mode). The display will show "open" and the green LED will light up.
With RotoBolt and MotorLock locks, turn the safe door handle to the open position.
With StraightBolt and SpringBolt locks, rotate the knob or handle according to the type of
installation and move the lock bolt to the open position.
For all types of locks the bolt must be able to move freely.
LOCKING:
With RotoBolt and MotorLock locks, turn the safe door handle to the locked position. Lock bolt
must fully extend and ensure locking.
With MotorLock locks with manual relocking, turn the door handle towards the locked position and
press the button .
Lock bolt must fully extend and ensure locking.
With StraightBolt lock, rotate the knob or handle according to the type of installation and move
the lock bolt to the locked position..
Lock bolt must fully extend and ensure locking.
Make sure that there is free space in all directions around the bolt when the movement is brought
to the locked position.
Repeat the functional test several times before closing the safe door.
Failure to follow these installation instructions or opening the lock by personnel not
authorized by Tecnosicurezza will void the warranty.

II_DigiTech_01_eng 15 of 20
Installation instructions
DigiTech
CE declarations
DICHIARAZIONE CE DI CONFORMITA’
CE DECLARATION OF CONFORMITY
DigiTech: T951-x
Il sottoscritto Franco Miller, in veste di Presidente CdA e Legale Rappresentante
della società Tecnosicurezza s.r.l., con sede in San Giovanni Lupatoto (Verona) Via Cesare
Battisti 276, dichiara sotto la propria responsabilità, che il suddetto prodotto soddisfa per
progettazione e costruzione i requisiti delle direttive di: compatibilità elettromagnetica
2014/30/EU e RoHS 2 2011/65/UE. La conformità è stata verificata con l’ausilio delle seguenti
norme armonizzate:
EN 61000-6-3, EN50130-4,EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN
61000-4-6, EN 61000-4-11, EN 61000-6-1, EN55022
The undersigned Mr Franco Miller as Chairman and Legal Representative of the
company Tecnosicurezza s.r.l., located in San Giovanni Lupatoto (Verona) Via Cesare Battisti
276, declare herewith on our own responsibility that the above-mentioned product meets the
requirements of the 2011/65/UE RoHS 2, 2014/30/EU Electromagnetic Compatibility for what
concerns engineering and construction. Conformity has been controlled with the aid of the
following harmonized standards:
EN 61000-6-3, EN50130-4,EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN
61000-4-6, EN 61000-4-11, EN 61000-6-1, EN55022
Verona - Italy, 02/10/2018
Franco Miller
Board Chairman

16 of 20 II_ DigiTech_01_eng
Installation instructions
DigiTech
DICHIARAZIONE CE DI CONFORMITA’
CE DECLARATION OF CONFORMITY
DigiTech: T51-xx
Il sottoscritto Franco Miller, in veste di Presidente CdA e Legale Rappresentante
della società Tecnosicurezza s.r.l., con sede in San Giovanni Lupatoto (Verona) Via Cesare
Battisti 276, dichiara sotto la propria responsabilità, che il suddetto prodotto soddisfa per
progettazione e costruzione i requisiti delle direttive di: compatibilità elettromagnetica
2014/30/EU e RoHS 2 2011/65/UE. La conformità è stata verificata con l’ausilio delle seguenti
norme armonizzate:
EN 61000-6-3, EN50130-4,EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN
61000-4-6, EN 61000-4-11, EN 61000-6-1, EN55022
The undersigned Mr Franco Miller as Chairman and Legal Representative of the
company Tecnosicurezza s.r.l., located in San Giovanni Lupatoto (Verona) Via Cesare Battisti
276, declare herewith on our own responsibility that the above-mentioned product meets the
requirements of the 2011/65/UE RoHS 2, 2014/30/EU Electromagnetic Compatibility for what
concerns engineering and construction. Conformity has been controlled with the aid of the
following harmonized standards:
EN 61000-6-3, EN50130-4,EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN
61000-4-6, EN 61000-4-11, EN 61000-6-1, EN55022
Verona - Italy, 02/10/2018
Franco Miller
Board Chairman

II_DigiTech_01_eng 17 of 20
Installation instructions
DigiTech
NOTES

18 of 20 II_ DigiTech_01_eng
Installation instructions
DigiTech
NOTES

II_DigiTech_01_eng 19 of 20
Installation instructions
DigiTech
NOTES

Correct disposal of this product:
(Waste Electrical & Electronic Equipment)
Applicable in the European Union and other European countries with separate collection systems.
This marking displayed on the product or its literature indicates that it should not be disposed with other wastes at the end of its
working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Contacts
GLOBAL HEADQUARTERS
USA HEADQUARTERS
SPAIN HEADQUARTERS
Tecnosicurezza SpA
Tecnosicurezza Inc.
Tecnosicurezza Sa
Via Cesare Battisti, 276
50, Thomas Lane
C/Menor, 4 - Nave 10
37057 San Giovanni Lupatoto
Verona
Versailles, KY 40383
Pol. Ind La Mina 28770
Colmenar Viejo
Tel.[phone]
Tel.[phone]
Tel.[phone]
Fax. [phone]
Fax.[phone]
[e-mail]
[e-mail]
[e-mail]