Tecnosicurezza TechMaster User manual

TechMaster
User Instructions

2 of 28 IU_ TechMaster_07_eng
User instructions
TechMaster
Table of contents
TABLE OF CONTENTS 2
IMPORTANT NOTES! 4
GENERAL INFORMATION 5
OVERVIEW FUNCTIONS 8
OPENING THE LOCKS 9
USERS (OR OVERRIDE USERS): OPENING WITHOUT TIME DELAY 9
USERS:OPENING WITH TIME DELAY 9
MANAGER (OR OVERRIDE MANAGER): OPENING WITHOUT TIME DELAY 10
MANAGER (OR OVERRIDE MANAGER): OPENING WITH TIME DELAY 10
OPENING WITH DYNAMIC CODES (DALLAS KEY OPTION)10
OPENING WITH DYNAMIC CODES (PIN OPTION)11
DUAL MODE OPENING WITHOUT TIME DELAY 11
DUAL MODE OPENING WITH TIME DELAY 11
MASTER MENU 12
TIME &DATE SETTINGS 12
TIME AND DATE RECOVERY THROUGH DYAMAWEB (OTC SOFTWARE)12
TIME LOCK SETTINGS 13
WEEKLY TIME LOCK SETTINGS –ADDING NEW VALUES 13
WEEKLY TIME LOCK SETTINGS –VERIFY OR DELETE VALUES 14
CLOSING PERIODS (HOLIDAYS)–ADD NEW VALUES 14
OPENING PERIODS -ADD NEW VALUES 15
OPENING PERIODS -VERIFY OR DELETE VALUES 16
PC CONNECTION 16
MANAGER MANAGEMENT 16
DYNAMIC CODES –ENABLING/DISABLING 17
DYNAMIC CODES ACTIVATION WITH STATIC CODES DELETING 17
MANAGER MENU 18
USERS MANAGEMENT 18
TIME DELAY 18
VARIABLE TIME DELAY –ADDING NEW VALUES 19
VARIABLE TIME DELAY –VERIFY OR DELETE VALUES 19
PC CONNECTION 19
OVERRIDE MANAGER MENU 20
OVERRIDE USERS MANAGEMENT 20
CODE CHANGING 20
CHANGE CODE FOR STANDARD AND OVERRIDE USERS 20
CHANGE CODE FOR MANAGER 21
CHANGE CODE FOR OVERRIDE MANAGER 21
CHANGE CODE FOR MASTER 21

IU_TechMaster_07_eng 3 of 28
User instructions
TechMaster
TIME MENU 22
OPENING EXTENSION 22
IMMEDIATE TIME LOCK 22
CONFIGURATION MENU 22
INSTALL LOCKS 22
REMOVE LOCKS 23
LOCK RECLOSURE MODE 23
INSTALL I/O INTERFACE 24
CONFIGURE I/O INTERFACE 24
REMOVE I/O INTERFACE 24
DISPLAY CONTRAST 25
KEYPAD LANGUAGE 25
MEMBRANE TEST 26
SYSTEM INFO 26
DYNAMIC KEYPAD ID AND DYAMAWEB SOFTWARE LICENSE 26
CORRECT DISPOSAL OF THIS PRODUCT: 28
(WASTE ELECTRICAL & ELECTRONIC EQUIPMENT) 28
CONTACTS 28

4 of 28 IU_ TechMaster_07_eng
User instructions
TechMaster
Important notes!
Before installing this product, please carefully read the installation and operating
instructions.
Locks have been designed to correctly operate in a temperature range from -5°C (23°F)
to + 50°C (122°F) and in an environment with non-condensing humidity between 25%
and 90%.
The lock must not be oiled/lubricated/greased.
If installed in normal domestic or office environments, the locks do not require
maintenance; in any case, after 10,000 opening/locking cycles, it is recommended to
conduct a test that verifies the correct and complete operation of the product.
Use only DURACELL™ 9 Volt Alkaline batteries, or battery holders with DURACELL™ 1.5
Volt Alkaline batteries. Alternatively, it is possible to use a 12VDC - 1A power adapter
(p.n. N1212) with relative power supply interface (p.n. T6006).
A long beep together with the message “LOW BATTERY” on the display, indicate a low
battery level which needs to be immediately replaced.
It is strongly recommended to change the default codes before use and to keep safely
the new codes.
Never use codes that can be easily guessed such as 123456, birth dates or based on
other personal information.
After changing a code, perform several opening/closing tests before closing the door.
Should the lock label be removed, warranty is void.

IU_TechMaster_07_eng 5 of 28
User instructions
TechMaster
General information
Using your keypad
Press any button to power up the keypad. LCD which displays:
ENTER CODE
X X –X X X X X X
If more locks are installed, LCD displays:
Enter the lock number to select it.
SELECT LOCK
To enter a code, power up the LCD and enter the corresponding
digits.
LCD automatically switches OFF if no buttons are pressed
within 30s.
To scroll the menu, press .
To confirm an operation or enter a menu press .
To leave a menu and come back to the main menu, scroll the
functions until “EXIT?” and press OK.
To enter a code plus Dallas key (if programmed), enter the code
digits and insert the Dallas key in the keypad reader.
To enter a user provided with Dallas key only (if programmed),
insert the Dallas key in the keypad reader. LCD displays:
DALLAS USER
XX
To start a time delay counting (if programmed), enter a code.
LCD displays:
TIME DELAY
00:59
To stop a time delay counting (if programmed), press and
then confirm with
STOP DELAY
COUNTING?
After time delay counting, LCD displays open window counting:
Press and enter a code for opening.
OPEN WINDOW
00:01
If a wrong code is entered, LCD displays the message:
WRONG CODE
If a wrong dynamic/activation code is entered, LCD displays the
message:
WRONG DYNAMIC
CODE

6 of 28 IU_ TechMaster_07_eng
User instructions
TechMaster
If a dynamic/activation code is entered more than 30 minutes
before its beginning validity time, LCD displays:
WRONG DYNAMIC
CODE
If a dynamic/activation code is entered more than 30 minutes
later than its beginning validity time, LCD displays:
WRONG DYNAMIC
CODE
To open or access the menu in dual mode (if programmed),
enter the first code. LCD displays:
Then, enter the second code.
ENTER 2° CODE
X X –X X X X X X
Using your Keypad in Scramble mode (required for class C)
Scramble mode is an additional security which allows to enter a code without using always the
same keys. User ID instead can still be entered as well as the Configuration menu code
To enter an opening code or a menu code in scramble mode, follow the steps below:
Enter the user ID. LCD displays:
ENTER CODE
[5] x x x x x x x
Enter the user code by pressing key or , respectively to increase
or decrease by 1 the digit selected ([X]). Press to confirm and to
switch to the next digit. All digits already entered are indicated by
capital symbol.
After entering the last digit, press to confirm the code.
Press to come back to the previous digit. When the first digit is
selected, press again to enter again the user ID.
ENTER CODE
X X X X X [ 8 ] x x
Shortcuts
Press and hold for 2 seconds the button related to the needed function:
= Change Manager code (01), users, override users, Master and Manager ovr (if configured)
= PIN entering for dynamic codes (after dynamic codes activation)
= Test mode

IU_TechMaster_07_eng 7 of 28
User instructions
TechMaster
= access to Manager menu, Manager ovr menu (if configured) Change code menu, Time
menu, Configuration menu and Master menu.
= System info and time and date info
= Exit and back to the main menu
= Master menu
User properties and default codes
Users can be programmed for opening with code only, code + Dallas key or with Dallas key only.
It is also possible to set a dual mode opening: in this case, entering the two users codes is
required to open the lock.
Default codes are:
Master: 1-2-3-4-5-6-7-8.
Manager: 123456.
Users from 02 to 90: 02-020202, 03-030303, and so on. They always open with time delay if
programmed.
Override users: through to the setup software, it is possible to configure users in between 10
and 90 (10-101010, 11-111111, and so on) as override users. They always open without time
delay.
For class C, all users codes, including Master and Manager, are 8-digits type.
Users from 02 to 90 and Override users have a default code such as 02-02020202, 03-03030303,
and so on.
The table below reports the functions for the main users.
Master
Manager
Access to Master Menu
Set time and date
Set Time Lock periods
Audit download
Manager Management
Enable/disable OTCs
Change code
PC Link
Access to Manager Menu
Standard users management
Override users management
Set time delay
Set variable time delay
PC Link
Audit download
Opening
Code changing
Set opening extension
Set immediate time lock
Override manager
Configuration menu
Access to Ovr. Manager menu
Override users management
Code changing
Install/remove locks
Set display contrast
Change language

8 of 28 IU_ TechMaster_07_eng
User instructions
TechMaster
Test mode
Check system Information
Override users
Standard users
Opening
Change code
Opening
Set opening extension, if enabled
Set immediate time lock, if enabled
Code changing
This user manual describes the standard programming. According to such programming and
unless different requests made while ordering the product, an opening can be performed by
entering single users codes (no dual mode) and without time delay. Thus, the user manual must
be adapted according the configuration selected.
It is strongly recommended to change the default codes before using the lock.
Overview functions
Lock opening
After entering an opening code, it is possible to open the lock within 3 seconds. It’s no necessary
instead with motorized locks: in this case indeed, the motor moves the bolt which remains in
opening position for about 8 seconds before returning in closing position. In the manual closing
version instead, the bolt can be closed by pressing key for few seconds.
Penalty
Four consecutive wrong codes initiate a four-minutes penalty time. During this period, LCD
displays the message “PENALTY” and no operation is allowed.
For class C, the minimum penalty time is of 5 minutes.
Time Delay
Programmable time delay in between 0 and 99 minutes. Programmable opening window in
between 1 and 19 minutes.
Dallas keys
It can be programmed for any lock. Available as option for Manager and users (not for Master).
TechMaster keypad only works with Dallas keys created by TECNOSICUREZZA. Upon express
request, the keypad can be set in order to work also with different Dallas key models.
Power supply
Lock can be powered with:
an ALKALINE 9V battery located in the battery compartment below the keypad;
an internal battery box provided by Tecnosicurezza (6 ALKALINE 1.5 batteries);

IU_TechMaster_07_eng 9 of 28
User instructions
TechMaster
A power adapter (ref. N1212) with power supply interface (ref. T6005/W or T6005) both
provided by Tecnosicurezza.
Low battery warning
A long beep together with the message “LOW BATTERY” on the display, indicates a low battery
level which should be immediately replaced.
Silent alarm
With this function enabled, enter an opening code increasing or decreasing by one number
the last code digit (ex. 03-030304 or 03-030302 instead of 03-030303): the lock opens and
simultaneously the output of the alarm interface or I/O interface is activated.
Tamper alarm (required for class C)
This function provides a blocking of the system and displays a warning message “ANTI_TAMPER
ALARM” whenever the keypad is removed from the door, or the battery compartment get
opened. Insert a valid code to unblock the keypad and restore the normal functioning.
Audit
The lock saves the last 6000 operations with time, date, user and operations description. The
keypad can save the last 250 operations. It is possible to download the events for locks and
keypad by using the Tecnosicurezza DMT Audit software. For further information refer to the
IU_DMT_Audit_XX.
IMPORTANT
Some options/characteristics reported in this user manual, can only be used if previously
programmed through the setup software. Therefore, please refer to the user manual
IU_TechMaster_setup_XX. Please contact Tecnosicurezza for further information.
Opening the locks
Users (or Override users): opening without time delay
Power up the keypad. Enter an opening code and insert the Dallas key,
if programmed. LCD displays:
OPEN
Open the lock within 3 seconds.
Users: opening with time delay
Power up the keypad. Enter an opening code and insert the Dallas key,
if programmed.
LCD displays the time delay counting:
TIME DELAY
00:59
At time elapsed, the LCD displays the open window counting time.
OPEN WINDOW
00:01
Press , LCD displays:
ENTER CODE
X X –X X X X X X

10 of 28 IU_ TechMaster_07_eng
User instructions
TechMaster
Enter an opening code and insert the Dallas key, if programmed. LCD
displays:
OPEN
Open the lock within 3 seconds.
Manager (or Override Manager): opening without time delay
Power up the keypad. Press for opening with Manager code or
press it two times for opening with Manager Ovr code. LCD displays:
MANAGER CODE
X X X X X X
Enter Manager code and insert the Dallas key, if programmed (or enter
Manager Ovr code and insert the Dallas key, if programmed). LCD
displays:
OPEN
Open the lock within 3 seconds.
Manager (or Override Manager): opening with time delay
Power up the keypad. Press for opening with Manager code or
press it two times for opening with Manager Ovr Code. LCD displays:
MANAGER CODE
X X X X X X
Enter Manager code and insert the Dallas key, if programmed (or enter
Manager Ovr Code and insert the Dallas key, if programmed). LCD
displays the time delay counting:
TIME DELAY
00:59
Once the time delay has elapsed, the LCD displays the open window
counting time.
OPEN WINDOW
00:01
Press , LCD displays:
ENTER CODE
X X –X X X X
Press for opening with Manager code or press it two times for
opening with Manager Ovr code. LCD displays:
MANAGER
X X X X X X
Enter Manager code/Manager Ovr code and insert the Dallas key, if
programmed. LCD displays:
OPEN
Open the lock within 3 seconds.
Opening with dynamic codes (Dallas key option)
Power up the keypad. Insert the Dallas dynamic key in the Dallas
reader. LCD displays:
DYNAMIC CODE
X X X X X X X X X
Enter the dynamic code and press . LCD displays:
OPEN
Open the lock within 3 seconds.
If programmed by the software Dyama or DyamaWeb for dynamic
codes creation, LCD displays the closing code when the bolt re-closes.
Please refer to the user manuals IU_Dyama_XX or IU_DyamaWeb_XX
for further information.
CLOSING CODE
179
WARNING: dynamic codes must be used respecting the sequence of
activation time in which they have been created by the software
DYNAMIC CODE
DELETED

IU_TechMaster_07_eng 11 of 28
User instructions
TechMaster
(Dyama or DyamaWeb), otherwise the last created code deletes all the
previous ones (i.e. if three codes are created and the third one is used
before using the first two ones, those first two codes are deleted). In
this case indeed LCD displays:
Opening with dynamic codes (PIN option)
Power up the keypad. Press and hold to enter the dynamic user PIN
(optional). LCD displays:
DYNAMIC USER
X X X X
Enter the dynamic user PIN. LCD displays:
DYNAMIC CODE
X X X X X X X X X
Enter the dynamic code and press . LCD displays:
OPEN
Open the lock within 3 seconds.
If programmed by the software Dyama or DyamaWeb for dynamic
codes creation, LCD displays the closing code when the bolt re-closes.
Please refer to the user manuals IU_Dyama_XX or IU_DyamaWeb_XX
for further information.
CLOSING CODE
179
WARNING: dynamic codes must be used within the activation time
created by the software (Dyama or DyamaWeb), otherwise the last
created code deletes all the previous ones (i.e. if three codes are
created and the third one is used before using the first two ones, those
first two codes are deleted). In this case indeed LCD displays:
DYNAMIC CODE
DELETED
Dual mode opening without time delay
Power up the keypad. Enter an opening code and insert the Dallas key,
if programmed. LCD displays:
2° USER CODE
X X –X X X X X X
Enter the second opening code and insert the Dallas key, if
programmed.
LCD displays:
OPEN
Open the lock within 3 seconds.
Dual mode opening with time delay
Power up the keypad. Enter an opening code and insert the Dallas key,
if programmed.
LCD displays the time delay counting:
TIME DELAY
00:59
When the time delay has elapsed, the LCD displays the open window
counting time.
OPEN WINDOW
00:01
Press , LCD displays:
ENTER CODE
X X –X X X X X X
Enter an opening code and insert the Dallas key, if programmed.
LCD displays:
2° USER CODE
X X –X X X X X X

12 of 28 IU_ TechMaster_07_eng
User instructions
TechMaster
Enter the second opening code and insert the Dallas key, if
programmed.
LCD displays:
OPEN
Open the lock within 3 seconds.
Master menu
Power up the keypad. Press and hold . LCD displays:
MASTER MENU
X X X X X X X X
Enter Master code (default value 1-2-3-4-5-6-7-8).
Time & date settings
Enter the Master menu. Press until LCD displays:
TIME AND me
SETTINGS
Press . LCD displays the current time and date.
08:00 FRI
27/01/2006
Press to change time and date.
hh:mm _ _ _
GG / MM / YYYY
Enter the new time and date values and press to confirm.
Time and Date recovery through DyamaWeb (OTC software)
This option can only be performed after activating the dynamic codes and the deletion of all
static codes (including the Master code). For further information, see the paragraph
Dynamic codes activation with static codes deleting, pg. 18. This option allows for the
updating of the time and date values by using the keypad along with the DyamaWeb
software. (for further information, see user manual IU_DyamaWeb_XX or
IU_DyamaWebLite_XX).
Power up the keypad and press and hold until the keypad firmware
version is displayed.
Press until the LCD displays the current time and date.
08:00 FRI
01/27/2006
Press and hold . LCD displays:
TIME/DATE ERROR
MODE ACTIVATED!
Insert the blue Dallas key N1971 in the reader. LCD displays:
TIME/DATE ERROR
XXXX XXXX
Enter the 8-digits code displayed on the LCD into DyamaWeb software,
to generate the dynamic code to access the Time & Date menu, to
update time and date values.
Press . LCD displays:
DYNAMIC CODE
X X X X X X X X X

IU_TechMaster_07_eng 13 of 28
User instructions
TechMaster
Enter the dynamic code generated by DyamaWeb software: LCD
displays the current values for time and date.
Press to enter the new time and date values and press to
confirm.
DST Settings
WARNING: it is recommended to enter this menu always with the door
open.
Power up the keypad. Enter the Master menu. Press until LCD
displays:
AUTOMATIC DST
Press one time and then press to select between ON and OFF.
Press again to confirm.
If the static codes have been deleted, automatic DST can be enabled by using the dynamic
user DST.
Time Lock settings
WARNING:
It is recommended to enter this menu always with the door open;
Master menu, allows to add/delete the settings for time lock/closing periods/opening
periods, only if current time and date values are included in an opening period.
Power up the keypad. Enter the Master menu. Press until LCD
displays:
TIME LOCK
SETTING
Weekly time lock settings –Adding new values
Enter Time Lock menu and press . LCD displays:
WEEKLY TIME LOCK
T1 SETTING
Press once or two times to set a weekly time lock T2 or T3. Then,
press .
Press . LCD displays:
ADD NEW VALUES
Press . LCD displays the current day of the week.
hh:mm FRI
hh:mm
The first entry is an opening time while the second entry is a closing
time. Enter the new values.
Press to confirm. LCD displays the next day of the week, proposing
the same time values. Press to confirm or to select another
day without entering new time values or else enter the new time values
as previously illustrated.
At the end of the week, LCD displays:
END OF LIST
EXIT AND SAVE? 

14 of 28 IU_ TechMaster_07_eng
User instructions
TechMaster
Press to save or for coming back to the first weekday.
All values entered can be saved only by pressing .
Inside the Time Lock menu, opening time intervals are indicated: it means the safe can be
opened by entering a valid code, but only inside the time interval itself (ex. opening time
interval from 08.00 to 14.00 from Monday to Friday: the safe can be only opened from
08.00 to 14.00 and only in those days, it cannot be opened before 08.00 and after 14.00.
Furthermore, safe cannot be opened on Saturdays and Sundays).
It is possible to schedule up to four times intervals per day (ex. Monday from 07.00 to
10.00, from 12.00 to 13.00, 15.00 to 16.00 and 18.00 to 19.00).
Weekly time lock settings –Verify or delete values
Enter Time Lock menu and press . LCD displays:
WEEKLY TIME LOCK
T1 SETTING
Press . LCD displays:
ADD NEW VALUES
Press . LCD displays:
VERIFY OR DELETE
VALUES
Press . LCD displays the values for the first day.
hh:mm FRI
hh:mm
Press to scroll all the schedules list.
Press on a schedule. LCD displays:
DELETE VALUES?

Press to confirm or to exit.
At the end of the list, press . LCD displays:
END OF LIST
EXIT?
Closing periods (Holidays) –Add new values
Closing periods are time intervals in which is possible to close the lock even when a time
lock is enabled.
It is possible to schedule up to 60 closing periods (they can be opening or closing periods).
Each period has a maximum time length of 14 days.
WARNING: during closing periods, the safe cannot be opened.
Enter Time Lock menu and press until LCD displays:
WEEKLY TIME LOCK
T1 SETTING
Press . LCD displays:
CLOSING PERIODS
SETTING
Press . LCD displays:
ADD NEW VALUES
Press . LCD displays:
GG/MM/AA hh:mm
GG/MM/AA hh:mm
The first entry is a closing time while second entry is an opening time.

IU_TechMaster_07_eng 15 of 28
User instructions
TechMaster
Enter the time of start and the ending time for the closing period, then
press to confirm.
Should the year be programmed, the closing period is not repeated.
Should not the year be programmed (press ), the closing period is yearly repeated
instead.
Press to delete all values entered.
Repeat the steps above for each closing period.
Closing periods (OFF days) –Verify or delete values
Enter Time Lock menu and press . LCD displays:
WEEKLY TIME LOCK
T1 SETTING
Press until the LCD displays:
CLOSING PERIODS
SETTINGS
Press . LCD displays:
ADD NEW VALUES
Press . LCD displays:
VERIFY OR DELETE
VALUES
Press to check the first closing period scheduled.
GG/MM/AA hh:mm
GG/MM/AA hh:mm
Press to scroll all the scheduled closing periods.
Press to delete the scheduled closing periods.
DELETE VALUES?

Press to confirm or to exit.
At the end of the list, press .
END OF LIST
EXIT?
Opening periods - Add new values
Opening periods are time intervals in which is possible to open the lock even when a time
lock is enabled.
It is possible to schedule up to 60 closing periods (they can be opening or closing periods).
Each period has a maximum time length of 14 days.
Enter Time Lock menu and press . LCD displays:
WEEKLY TIME LOCK
T1 SETTING
Press until the LCD displays:
OPENING PERIODS
SETTINGS
Press . LCD displays:
ADD NEW VALUES
Press . LCD displays:
GG/MM/AA hh:mm
GG/MM/AA hh:mm
The first entry is an opening time while the second entry is a closing
time.

16 of 28 IU_ TechMaster_07_eng
User instructions
TechMaster
Enter a date and time for opening and closing, then press to
confirm.
Should the year be programmed, the opening period is not repeated.
Should not the year be programmed (press ), the opening period is yearly repeated
instead.
Press to delete the values entered.
Opening periods - Verify or delete values
Enter Time Lock menu and press . LCD displays:
WEEKLY TIME LOCK
T1 SETTING
Press until the LCD displays:
OPENING PERIODS
SETTINGS
Press . LCD displays:
ADD NEW VALUES
Press . LCD displays:
VERIFY OR DELETE
VALUES
Press . LCD displays the first opening period.
GG/MM/AA hh:mm
GG/MM/AA hh:mm
Press to scroll all the scheduled opening periods.
Press to delete. LCD displays:
DELETE VALUES?

Press to confirm or to exit.
At the end of the list, press .
END OF LIST
EXIT?
PC connection
Use this function to enable the connection between the keypad and PC.
Power up the keypad. Enter the Master menu. Press until LCD
displays:
PC LINK
Press to start the connection with PC.
PC LINK
…
Press to stop the connection with PC.
If the static codes have been deleted, PC connection can be enabled by using the dynamic
user AUDIT.
Manager Management
Power up the keypad. Enter Master menu. Press until the LCD
displays:
MANAGER
MANAGEMENT

IU_TechMaster_07_eng 17 of 28
User instructions
TechMaster
Press . LCD displays:
1 MANAGER 
2 AMMINISTRAT.
“ ” installed, “_” deleted, “X” disabled.
Select Manager by entering its reference number and press .
If the Manager is not installed, LCD displays:
01
INSTALL?
Press to confirm. Then enter the new Manager code and confirm
it. LCD displays:
OPERATION DONE
If the Manager is already installed, press for
disabling/deleting/installing it. Then press to confirm.
Dynamic codes –Enabling/Disabling
WARNING: it is recommended to always perform this operation with door open, to
enable/disable the dynamic codes. Later, dynamic codes can be activated through the red
Dallas key 1971 previously programmed with the software Dyama or DyamaWeb.
Power up the keypad. Enter Master menu. Press until the LCD
displays:
DYNAMIC CODES
Press . LCD displays:
DYNAMIC CODES
ENABLED/DISABLED
Press . The LCD displays:
DYNAMIC CODES
ENABLE/DISABLE?
Press to confirm. LCD displays:
OPERATION DONE
Dynamic codes activation with static codes deleting
WARNING: with this operation, it is possible to delete the static codes for all users and
Manager. Furthermore, depending on the configuration selected, Master static code may
be deleted as well.
Insert the red Dallas key N1971 in the reader. LCD displays:
DYNAMIC CODE
XXX
Enter the activation code generated by the software Dyama or
DyamaWeb and press . LCD displays:
DELETE ALL THE
STATIC CODES?
Press . LCD displays:
OPERATION IN
PROGRESS…
Once completed, LCD displays:
DYNAMIC CODES
ACTIVE
To re-install the static codes (only for Master and Manager) use the dynamic user
REMOVAL. Later, it is possible to re-install all the other users from the menu Users
management.

18 of 28 IU_ TechMaster_07_eng
User instructions
TechMaster
Manager menu
Power up the keypad.
Press , then press . LCD displays:
MANAGER MENU
X X
Users Management
Power up the keypad. Enter Manager menu and press until LCD
displays:
USERS MANAGEMENT
Press and press to scroll users list or enter user ID.
02 03 04 05 06
x _ _ 
“ ” user installed, “_” user deleted, “X” user disabled.
Override users 50 ÷ 59 can only be installed when the lock is open.
Press . If the user is not installed LCD displays:
02
INSTALL?
“” Dallas key, “ ” code, “+” dual mode, “TL” time lock
Press to confirm or to exit or for switching to the next user.
Enter the new user code and confirm it.
If the selected user is already installed, press to choose whether
to disable it, to delete it or for leaving and selecting another user.
Press to confirm the choice.
Time delay
Power up the keypad. Enter Manager menu and press until LCD
displays:
T. DELAY AND
O. WINDOW
Press to confirm. LCD displays the current values for time delay
and open window.
TIME DELAY 00
OPEN WINDOW 01
Press to exit or to program new values.
TIME DELAY mm
OPEN WINDOW mm
Enter the new values and press to confirm. LCD displays:
VALUES UPDATED
Time delay can be programmed between 0 and 99 minutes, the open window can be
programmed between 1 and 19 minutes instead.
To program a shorter time delay, lock must be open.
Variable Time Delay
WARNING: lock must always be open to set a variable time delay
VARIABLE
TIME DELAY

IU_TechMaster_07_eng 19 of 28
User instructions
TechMaster
Power up the keypad. Enter Manager menu and press until LCD
displays:
Variable Time Delay –Adding new values
Enter Variable Time Delay menu and press . LCD displays:
ADD NEW VALUES
Press . LCD displays the current day of the week.
hh:mm VEN
hh:mm :mm
Enter values for starting time and ending time in which Variable Time
Delay must be active and then enter the values of Variable Time
Delay.
Press to confirm. LCD displays the next day of the week,
proposing the same time values. Press to confirm or to select
another day without entering new time values or otherwise enter the
new time values as previously illustrated.
At the end of the week, LCD displays:
END OF LIST
EXIT AND SAVE? 
Press to save the values or for coming back to the first
weekday.
After saving the values, LCD displays:
Press to set new values (max. 4)
ADD NEW VALUES
Variable Time Delay –Verify or delete values
Enter Variable Time Delay menu and press until LCD displays:
VERIFY OR DELETE
VALUES
Press . LCD displays the values for the first day.
08:00 DOM
10:00 : 01
Press to scroll all the schedules list.
Press on a schedule. LCD displays:
DELETE VALUES?

Press to confirm the deletion or to exit.
At the end of the list, press . LCD displays:
END OF LIST EXIT
AND SAVE? 
PC connection
Use this function to enable the connection between the keypad and PC.
Power up the keypad. Enter the Manager menu. Press until LCD
displays:
PC LINK
Press to start the connection with PC.
PC LINK
…

20 of 28 IU_ TechMaster_07_eng
User instructions
TechMaster
Press to stop the connection with PC.
If the static codes have been deleted, PC connection can be enabled by using the dynamic
user AUDIT.
Override Manager menu
Power up the keypad.
Press , then press until LCD displays:
OVR MANAGER MENU
X X X X X X
Enter OVR Manager code (default code 6-5-4-3-2-1).
Override Users management
WARNING: to install new override users, lock must be open.
Power up the keypad. Enter Override Manager menu and press
until LCD displays:
OVR USERS
MANAGEMENT
Press and press to scroll users list or enter user ID.
50 51 52 53 54
x _ _ 
“ ” user installed, “_” user deleted, “X” user disabled.
Press . If the user is not installed LCD displays:
52
INSTALL?
“ ” Dallas key, “ ” code, “+” dual mode, “TL” time lock
Press to confirm or to exit or for switching to the next user.
Enter the new user code and confirm it.
If the selected user is already installed, press to choose whether to disable it, to delete
it, selecting another user or exit. Press to confirm the choice.
Code changing
WARNING: it is recommended to always perform this operation with door open.
Power up the keypad.
Press , then press until LCD displays:
CHANGE CODE
Change code for standard and override Users
Power up the keypad. Access Change Code menu and press . LCD
displays:
CHANGE USER
CODE
Press to confirm. LCD displays:
ENTER OLD CODE
X X –X X X X X X