Tecnosicurezza DigiTech User manual

DigiTech
User Instructions

2 of 16 IU_ DigiTech_04
User instructions
DigiTech
Company
Founded in 1983 with the aim of providing a complete range of professional products,
Tecnosicurezza is now a consolidated reality in the field of locks and security systems for safes.
The experience gained in over 35 years of activity in the security sector has allowed the
designing and manufacturing of high technology and reliability systems, which continue to
receive the approval of an increasingly demanding clientele.
TECNOSICUREZZA is present directly on the Italian, Spanish and US markets and, through a
extensive distribution network, in many European and extra-European countries.
TECNOSICUREZZA is aimed at national and international customers of primary importance, such
as banks, safe manufacturers, cash in transit companies, mass market retailers and post offices.
Today TECNOSICUREZZA is a leading company focused on the customers’ needs and
constantly in step with technology.

IU_DigiTech_04 3 of 16
User instructions
DigiTech
Table of contents
COMPANY 2
TABLE OF CONTENTS 3
IMPORTANT NOTES! 4
GENERAL INFORMATION 5
OVERVIEW FUNCTIONS 7
LOCK OPENING 8
PRE-SETUP MODE 8
MANAGER (01) AND USERS (02-29): 8
OVERRIDE USER (30) 8
CODE CHANGING 9
USER MANAGEMENT 9
LOCK SETUP 10
SETUP WITH DALLAS KEY 10
SETUP WITH PC 10
TEST MODE 10
KEYPAD LANGUAGE 11
AUDIT 11
EVENTS CHECK ON LCD 11
DOWNLOAD THE AUDIT ON A DALLAS KEY 12
DOWNLOAD AUDIT ON PC 12
FIRMWARE VERSION 12
CONTRAST ADJUSTMENT 13
TIME DELAY 13
TIME, DATE AND DST SETTINGS 13
TIME &DATE SETTINGS 13
DST SETTINGS 14
CONTACTS 16

4 of 16 IU_ DigiTech_04
User instructions
DigiTech
Important notes!
•Before installing this product, please read carefully the installation and operating
instructions.
•Locks have been designed to correctly operate in a temperature range from -5°C to +
50°C and and in an environment with non-condensing humidity between 25% and 90%.
•The lock must not be oiled/lubricated/greased.
•If installed in normal domestic or office environments, the locks do not require particular
maintenance; in any case, after 10,000 opening/locking cycles, it is recommended to run
a test that verifies the correct and complete operation of the product.
•Use only DURACELL™ 9 Volt Alkaline batteries, or battery holders with DURACELL™ 1.5
Volt Alkaline batteries. Alternatively, it is possible to use a 12VDC - 1A power adapter
(p.n. N1212) with relative power supply interface (p.n. T6005/W or p.n. T6005).
•Una serie di segnalazioni acustiche durante l’apertura indicano un livello di batteria
basso. La batteria deve essere in tal caso sostituita.
•It is strongly recommended to change the default codes before the usage and to keep
safely the new codes.
•Do never use codes easy to be guessed such as 123456, birth dates or others, based on
own personal information.
•After changing a code, perform several opening/closing tests before closing the door.
Should the lock label be removed, warranty is void.

IU_DigiTech_04 5 of 16
User instructions
DigiTech
General information
Using your keypad
•Press any button to power up the keypad. LCD which shows:
ENTER CODE
X X –X X X X X X
If the lock is in pre-setup mode, LCD shows:
PRESS 1 TO OPEN
•To enter a code, power up the LCD and enter the corresponding
digits.
•LCD automatically switches OFF if no buttons are pressed
within 30s.
•To scroll the menu, press .
•To confirm an operation, press .
•To leave a menu or come back to the main menu, scroll the
functions until “EXIT?” and press .
•To enter a code plus Dallas key (if set), enter the code digits and
insert the Dallas key in the keypad reader.
•To enter a user provided with Dallas key only (if set), insert the
Dallas key in the keypad reader. LCD shows:
DALLAS USER
XX
•To start a time delay counting (if set), enter a code. LCD shows:
TIME DELAY
00:59
•To stop a time delay counting, press and then confirm with
STOP DELAY
COUNTING?
After the time delay counting, LCD shows open window
counting:
Press and enter a code for opening.
OPEN WINDOW
00:01

6 of 16 IU_ DigiTech_04
User instructions
DigiTech
•If a wrong code is entered, LCD displays the message:
WRONG CODE
•To open or access the menu in dual mode (if set), enter the first
code. LCD shows:
Then, enter the second code.
ENTER 2° CODE
X X –X X X X X X
Shortcuts
Press and hold for 2 seconds the button related to the needed function:
= Change Manager code (01), users (02-29) and override users (30)
= Users management
= Lock setup with Dallas key
= Test mode
= Change language
= Audit/Events check
= System info/Time and date view/Contrast adjustment
= Time delay and opening window
= Exit and back to the main menu
= Time and date settings/Automatic DST/PC link

IU_DigiTech_04 7 of 16
User instructions
DigiTech
Pre-setup & Configurations
When the lock is in pre-setup mode and connected with the keypad for the first time:
•lock can be simply opened by pressing the button 1. When the bolt is open, the output
connector BAT is enabled;
•only the following options are allowed: Test mode, Language selection,
PC Link, Events check, Time and date view, System information view, Contrast
adjustment.
Through the PC connection and the software DigiTech Setup, the lock can be set according
different configurations, involving the number of users, the dual mode opening and the
Manager management.
User properties and default codes
Users can be set for opening with code only, code + Dallas key or with Dallas key only. It is also
possible to set a dual mode opening: in this case, entering the two users codes is required to
open the lock.
Default codes are:
Manager: 01-123456.
Users from 02 to 29: 02-020202, 03-030303…..and so on. They always open with time delay if
set.
Override user 30: 30-303030. He always opens without time delay.
This user manual describes the standard programming. According such programming and unless
different requests while ordering the product, an opening can be performed by entering single
users codes (no dual mode) and without time delay. Thus, the user manual must be adapted
according the configuration selected.
It is strongly recommended to change the default codes before using the lock.
Overview functions
Lock opening
After entering an opening code, it is possible to open the lock within 3 seconds. It’s no necessary
instead with motorized locks: in this case indeed, the motor moves the bolt which remains in
opening position for about 8 seconds before returning in closing position. In the manual closing
version instead, the bolt can be closed by pressing key for few seconds.
Penalty
Four consecutive wrong codes initiate a four minutes penalty time. During this period, LCD
shows the message “ LOCK PENALTY” and no operation is allowed.

8 of 16 IU_ DigiTech_04
User instructions
DigiTech
Time Delay
Programmable time delay in between 0 and 99 minutes. Programmable opening window in
between 1 and 19 minutes.
Dallas keys
Available as option for Manager and users.
Power supply
Lock can be powered with:
•an ALKALINE 9V battery located in the battery compartement below the keypad;
•an internal battery box provided by Tecnosicurezza (6 ALKALINE 1.5 batteries);
•A power adapter (ref. N1212) with power supply interface (ref. T6005/W or T6005) both
provided by Tecnosicurezza.
Low battery warning
A long beep together with the message “LOW BATTERY” on the display, indicate a low battery
level which need immediate replacing.
Audit
The lock is able to save the last 5500 operations with time, date, user and operations
description.
IMPORTANT
Some options/characteristics reported in this user manual, can only be used if previously
enabled through the setup software. Thus, please refer to the user manual
IU_DigiTech_setup_XX.
Please contact Tecnosicurezza for further information.
Lock opening
Pre-setup mode
Power up the keypad. The Display shows:
Press to open the lock.
PRESS 1
TO OPEN
Manager (01) and users (02-29):
Power up the keypad and enter an opening code. LCD shows:
OPEN
Override user (30)
Power up the keypad and enter an override user code code (enter also
the Dallas key if set). LCD shows:
OPEN
Open the lock within 3 seconds.

IU_DigiTech_04 9 of 16
User instructions
DigiTech
Code changing
WARNING: it is recommended to always perform this operation with door open.
Manager (ID 01), users (ID 02-29) and override user (ID 30)
Power up the keypad. Press and hold . LCD shows:
ENTER OLD CODE
X X –X X X X X X
Enter the old code and insert the Dallas key in the reader (if set).
LCD shows:
ENTER NEW CODE
X X X X X X
Enter the new code. LCD shows:
CONFIRM CODE
X X X X X X
Confirm the new code.
User management
Power up the keypad. Press and hold . LCD shows:
USERS MANAGEMENT
0 1 –X X X X X X
Enter Manager code. LCD shows:
02 03 04 05 06
✓x _ _ ✓
Press to scroll users list or enter user ID.
“ ” user installed, “_” user deleted, “X” user disabled.
The overide user (30) can only be installed when the bolt is open.
Press . If the user is not installed LCD shows the message:
02
INSTALL?
“ ” Dallas key, “ ” code, “+” dual mode, “TL” time lock
Press to confirm or to exit or for switching to the next user.
Enter the new user code and confirm it. LCD shows:
OPERATION DONE
If the selected user is already installed, press to choose whether
to disable it, to delete it or for leaving and selecting another user.
Press to confirm the choice.

10 of 16 IU_ DigiTech_04
User instructions
DigiTech
Lock setup
Lock setup can be performed through a Dallas key properly programmed or through a direct
PC link. In both cases, lock must be in pre-setup mode (press 1 to open it).
Setup with Dallas key
Power up the keypad. Press and hold . LCD shows:
SYSTEM SETUP
Insert the setup Dallas key in the reader and connect the reader with
the keypad by means of the jack connector. LCD shows:
08:00 FRI
27/01/2019
Check time and date. Press to confirm or to update the values.
Then, press again to confirm. LCD shows:
CONFIGURAZIONE IN
CORSO 10%
If the operation is successfully performed, LCD shows:
OPERATION DONE
Setup with PC
Power up the keypad. Press and hold . LCD shows:
TIME AND DATE
01-XXXXXX
Enter the manager code and press . LCD shows:
TIME AND DATE
SETTINGS
Press until LCD shows:
PC LINK
Press , LCD shows:
PC LINK
...
Start the programming on the Setup software or press to exit.
If the operation is successfully performed, LCD shows the firmware
version and few seconds later the keypad switches OFF. Pease refer to
the user manual IU_DigiTech_setup_XX for further information.
Test mode
This function allows to check the correct system operation.
Power up the keypad. Press and old . LCD shows:
TEST MODE
1234567890 ➔
Enter the sequence of buttons shown on the LCD.
TEST MODE
1234567890 ➔
Any working button produces a short beep.
A damaged button produces a long beep. LCD shows:
WRONG/FAULTY
KEY

IU_DigiTech_04 11 of 16
User instructions
DigiTech
Two short beeps are produced if the test terminates successfully. LCD
shows:
OPERATION
DONE
Keypad language
Power up the keypad. Press and old . LCD shows:
ITALIANO
1 2 3
Enter one of the numbers shown on the LCD to select a new language
(the new language will be automatically changed). Press to
confirm or to exit.
ENGLISH
1 2 3
Audit
Keypad and lock events can be checked on the LCD (only openings and closings). These
events can be also stored in a Dallas key previously programmed using “DMT Audit”
software.
Dallas key only allows to store the last 1200 events which can be later downloaded on PC
through an USB interface provided by Tecnosicurezza.
Direct PC connection allows to download all 5500 events, using an USB interface and a
specific software provided by Tecnosicurezza.
For further information, refer to the user manual IU_DMT_Audit_00_XX or contact
Tecnosicurezza.
Events check on LCD
Use this function to check all opening and closing events previously recorded.
Power up the keypad. Press and old . LCD shows:
LOCK AUDIT
0 1 –X X X X X X
Enter Manager code. LCD shows:
ENTER DALLAS
…
Wait for few seconds or press , LCD shows:
PC LINK ➔
SCROLL EVENTS
Press , LCD shows:
SCROLL EVENTS
ON LCD
Wait for few seconds, LCD shows the last opening/closing event.
001: WED
28/09 14:42:48
Press to scroll all the events or to exit.

12 of 16 IU_ DigiTech_04
User instructions
DigiTech
Download the audit on a Dallas key
Events can be downloaded through a Dallas key provided by Tecnosicurezza, specifically
programmed with the software Tecnosicurezza DMT Audit. For further information, refer to
the user manual IU_DMT_Audit_XX.
Power up the keypad. Press and old . LCD shows:
LOCK AUDIT
0 1 –X X X X X X
Enter Manager code. LCD shows:
ENTER DALLAS
…
Insert the Audit Dallas key into the reader. Events download begins
automatically. LCD shows:
DOWNLOADING
32%
If download is successful, LCD shows:
OPERATION DONE
Use the software Tecnosicurezza DMT Audit to download the events
on PC. For further information refer to the user manual
IU_DMT_Audit_XX or contact Tecnosicurezza.
Download audit on PC
Events can be downloaded through a USB interface provided by Tecnosicurezza.
Power up the keypad. Press and old . LCD shows:
LOCK AUDIT
0 1 –X X X X X X
Enter Manager code. LCD shows:
ENTER DALLAS
…
Wait for few seconds or press , LCD shows:
PC LINK
SCROLL EVENTS
Press , LCD shows:
PC LINK
...
Start the download using the software DMT Audit or press to exit.
For further information refer to the user manual IU_DMT_Audit_XX or
contact Tecnosicurezza.
Firmware version
Power up the keypad. Press and old . LCD shows:
DigiTech v 1.00
21/02/12
Press to see the current time and date. Press again to come
back to the main menu.

IU_DigiTech_04 13 of 16
User instructions
DigiTech
Contrast adjustment
Power up the keypad. Press and hold . LCD shows:
DigiTech v 1.00
21/02/12
Press and hold again . LCD shows:
ADJUST CONTRAST
1 2 3 4 5 6 7 8
Enter a value 1÷8 to select a different contrast level which will be quickly applied. Press
to confirm or to exit.
Time delay
Power up the keypad. Press and hold . LCD shows:
SET TIME DELAY
01 –X X X X X X
Enter Manager code. LCD shows the current values for time delay and
open window.
TIME DELAY 00
OPEN WINDOW 01
Press to exit or to set new values.
TIME DELAY mm
OPEN WINDOW mm
Enter the new values and press to confirm. LCD shows:
VALUES UPDATED
Time delay can be set in between 0 and 99 minutes, the open window in between 1 and 19
minutes instead.
To set a time delay shorter than the one curretly present, lock must be open.
Time, Date and DST settings
This menu allows for adjusting the current time and date. It also allows for enabling and
disabling the DST (Daylight-Saving-Time). For further information concerning this option,
please refer to the user manual IU_DigiTech_setup_XX or contact Tecnosicurezza.
Power up the keypad. Press and hold . LCD shows:
TIME AND DATE
0 1 –X X X X X X
Time & Date settings
Enter the Manager code. LCD shows:
TIME AND DATE
SETTINGS
Press . LCD shows the current time and date.
08:00 FRI
27/01/2006
Press again to change time and date.
hh:mm _ _ _
GG / MM / YYYY

14 of 16 IU_ DigiTech_04
User instructions
DigiTech
Enter the new time and date values and press to confirm.
DST settings
Enter the Manager code. LCD shows:
TIME AND DATE
SETTINGS
Press until LCD shows:
Then, press .
AUTOMATIC DST
Press to choose whether enable (ON) or disable (OFF) this option
and press to confirm the choice. LCD shows:
CHECK
DATE/TIME VALUE

IU_DigiTech_04 15 of 16
User instructions
DigiTech
NOTE

Correct disposal of this product:
(Waste Electrical & Electronic Equipment)
Applicable in the European Union and other European countries with separate collection systems.
This marking displayed on the product or its literature indicates that it should not be disposed with other wastes at the end of its
working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other
types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Contacts
GLOBAL HEADQUARTERS
USA HEADQUARTERS
SPAIN HEADQUARTERS
Tecnosicurezza SpA
Tecnosicurezza Inc.
Tecnosicurezza Sa
Via Cesare Battisti, 276
50, Thomas Lane
C/Menor, 4 - Nave 10
37057 San Giovanni Lupatoto
Verona
Versailles, KY 40383
Pol. Ind La Mina 28770
Colmenar Viejo
Tel.[phone]
Tel.[phone]
Tel.[phone]
Fax. [phone]
Fax.[phone]
[email protected]
[email protected]
[email protected]