TECO A510-2001-H User manual

Contents
Chapter 1 Safety precautions..........................................................................................1
1.1 Before supplying power.............................................................................................1
1.2 Wiring ........................................................................................................................2
1.3 Before operation........................................................................................................2
1.4 Parameters setting ....................................................................................................3
1.5 Operation...................................................................................................................3
1.6 Maintenance, Inspection and Replacement...............................................................4
Chapter 2 Model Description...........................................................................................5
2.1 Nameplate Data.........................................................................................................5
2.2 Model Designation.....................................................................................................5
Chapter 3 Ambient Environment And Installation.........................................................6
3.1 Screw Torques for terminals......................................................................................6
3.2 Wiring the periphery devices of A510........................................................................7
3.3 Wiring ........................................................................................................................8
3.4 Terminal Description..................................................................................................9
3.5 Overall Dimension drawing......................................................................................12
3.5.1 Standard Model ....................................................................................................12
3.5.2 Built-in filter model (440V 1~60HP) .....................................................................16
Chapter 4 Software Index..............................................................................................18
4.1 Keypad Description..................................................................................................18
4.1.1 Panel Functions....................................................................................................18
4.2 Parameters list.........................................................................................................19
Chapter 5 Trouble Diagnosis and shooting.................................................................62
5.1 General....................................................................................................................62
5.2 Fault detection function ...........................................................................................62
5.3 Warning / self-diagnosis detection function.............................................................66
5.4 Auto-tuning error......................................................................................................72
5.5 PM motor auto-tuning error .....................................................................................73

1
Chapter 1 Safety Precautions
1.1 Before supplying power
Warning
The main circuit must be properly wiring. Single phase( R/L1, S/L2)/3-phase(R/L1,
S/L2, T/L3) are the input terminal of the power, which must not be mixed with
U/T1,V/T2 and W/T3 on use. In case of mixed use, supplying power will damage the
inverter.
Caution
The power voltage must be the same as the input voltage of the inverter.
When handling the inverter, do not draw the front cover directly. It is suggested to
handle the inverter body so as to prevent the front cover breaks off, avoiding the
inverter falling and causing injury or inverter damage.
Please mount the inverter on noncombustible materials such as metal. Mounting on or
near the flammable materials is not allowed in case fire happened.
If several inverters are mounted on a single control panel, the extra cooling fan shall
be added, so as to make the panel temperature below 40 ℃ and to prevent
overheating or fire.
Please firstly turn off the power before disassemble or assemble the operator. Fix the
operator according to the indicating diagram to avoid operation failure or no display
due to improper operation.
Warning
This product has passed the application level at IEC 61800-3 restricted areas. When
the product is used in some environments, there might be electromagnetic
interference. Therefore, appropriate test is recommended to be carried out before use
and grounding must be well done.
Caution
 Installation and use of the product must be conducted by a qualified professional
electrician.
The product installation must be applied by the means of fixed wiring.

2
1.2 Wiring
Warning
Always turn OFF the input power supply before inverter installation or wiring terminals,
so as to avoid electric shock or fire.
Wiring must be performed by an authorized person qualified in electrical work, to
avoid electric shock or fire.
Make sure the grouding terminal is well grounded. (220 V class: Grounding
impedance shall be less than 100Ω, 460 V class: Grounding impedance shall be less
than 10Ω)
Always test the operation of any emergency stop circuits after wiring. (Wiring is the
responsibility of the user.)
Never touch the input/output lines directly with your hands or allow any line to contact
the Inverter case. Never short the circuits.
Do not carry out the dielectric voltage withstand test on the inverter, which will cause
the semiconductor parts damage easily.
Caution
Make sure the input power meets that of the inverter, in order to avoid injury or fire.
Please connect the braking resistor and braking unit according to the related wiring
diagram in case fire occured.
Please fasten the terminal screws based on specified torque so as to avoid fire.
Do not connect the input power supply line to the output terminal of the inverter.
Do not connect the magnetic contactor and solenoid switch contacts to the output
terminal.
Do not connect the phase advancing capacitor or LC / RC filter to the output circuit.
Ensure the interference generated by the inverter and motor will not affect peripheral
sensors or devices.
1.3 Before operation
Warning
Make sure the inverter capacity is the same as the capacity set by inverter’s function
parameters 13—00 before supplying power.
If the line length between the inverter and the motor exceeds 25 meters, it needs to
reduce the carrier frequency (11-01) or additionally equip a output filter to reduce the
over-voltage or oscillation at the load end, so as to avoid motor damage.

3
1.4 Parameters setting
Caution
When carry out the rotatable automatic tuning, do not connect the motor to the load
(mechanical device).
When carry out the rotatable automatic tuning and the motor will rotate, make sure
around space of the motor is enough in order to avoid danger.
1.5 Operation
Warning
Make sure the front external cover is completely installed in prior to turn on the power.
Do not connect or disconnect the motor unit in operation, otherwise the inverter will
cause the inverter to trip because of over-current. The severe case will cause the
main circuit damage of the inverter.
When the reset function is in operation, keep away from the machine. The machine
will restart after the fault is cleared.
Do not operate the machine with wet hands.
It provides a independent emergency stop switch. This switch will be enabled when
the parameter is being set (see 11-55).
It provides an independent external hardware emergency switch, which emergently
shuts down the inverter output in the case of danger.
Make sure the operation order is closed before reset warning.
If choose to automatically restart after power recovery (07-00), the inverter will start
automatically after power is restored.
Before automatic tuning, make sure the conditions of surrounding systems and
mechanical devices to ensure the safety of personnel.
Never touch related terminals regardless of inverter in operation or in stop states to
avoid any danger.
After the power is cut off, the fan might continue to rotate for some time.
Caution
Do not touch the heating elements such as heat sink, braking resistor, etc.
The inverter enables easily the motor rotes from low speed to high speed. Please
make sure the allowable range of the motor and the machine.
When the product is supported by the use of the braking module, please pay attention
to related settings for operation.
Inspecting the circuit board signal should be avoided when the inverter is in operation.

4
Warning
Avoid electrical shock! The internal DC capacitor of the inverter discharges in 5
minutes after the power is cut off. Therefore, carry out disasemmbly/assembly or
inspection after 5 minutes when the discharge completes.
1.6 Maintenance, Inspection and Replacement
Warning
Before the maintenance and inspection, make sure the power is cut off and the
indicator light of the power is off (make sure the DC voltage does not exceed 25 v).
Since there are high voltage terminals in the inverter, do not touch these terminals
randomly.
In the case of power on, be sure the protection cover is installed. In addition, when the
protection cover is disassembled, be sure to cut off the power by the circuit breaker.
Only the designated professional can carry out the maintenance or parts replacement.
Caution
The ambient temperature of the inverter should be from -10 ℃ to +40(60) ℃
95%RH and the inverter shall be used in the non-condensing environment, free
from water dropping and metal dust in surrounding.
Disposal caution for the inverter
Caution
Treat as industrial waste when disposing of inverter and pay attention to the following
items:
Burning electrolytic capacitors of the inverter main circuit and printed circuit board
might cause explosion;
Burning the plastic parts such as inverter shell will produce toxic gases.

5
Chapter 2 Model Description
2.1 Nameplate Data
Inverter Model and Motor Rating
Input Power Specifications
Output Power Specifications
Series No.
2.2 Model Designation
UL and CE Marks
-
A510
A510 Series
4
Voltage Rating:
2: 220V
4: 440V
6: 690V
010
-
H3F
Motor Rating:
001: 1HP
002: 2HP
∫
150: 150HP
175: 175HP
215: 215HP
∫
535: 535HP
670: 670HP
Power Source Phase:
Blank: Both by single
and three phase
3: For Three phase
Noise Filter:
Blank: No RFI
F: RFI Bulit-in
Type:
H: Standard
(LED operator)
C: Drawing
(LCD operator)
(S/N Barcode)
(P/N Barcode)

6
Chapter 3 Ambient Environment And Installation
3.1 Screw Torques for terminals
To comply with UL standards, you shall use UL approved copper wires (rated 75 °C) and
round crimp terminals (UL Listed products) in the following table when connecting the main circuit
terminal. TECO recommends using crimp terminals manufactured by NICHIFU Terminal Industry
Co., Ltd and the terminal crimping tool recommended by the manufacturer for crimping terminals
and the insulating sleeve.
Wire size
mm2 (AWG)
Terminal
screw size
Model of
the round
crimp
terminal
Fastening torque
kgf.cm (in.lbs)
Model of
insulating
sleeve
Model of
crimp tool
0.75 (18) M3.5 R1.25-3.5
8.2 to 10 (7.1 to 8.7) TIC 1.25 NH 1
M4 R1.25-4 12.2 to 14 (10.4 to 12.1) TIC 1.25 NH 1
1.25 (16) M3.5 R1.25-3.5
8.2 to 10 (7.1 to 8.7) TIC 1.25 NH 1
M4 R1.25-4 12.2 to 14 (10.4 to 12.1) TIC 1.25 NH 1
2 (14)
M3.5 R2-3.5 8.2 to 10 (7.1 to 8.7) TIC 2 NH 1 / 9
M4 R2-4 12.2 to 14 (10.4 to 12.1) TIC 2 NH 1 / 9
M5 R2-5 22.1 to 24 (17.7 to 20.8) TIC 2 NH 1 / 9
M6 R2-6 25.5 to 30.0 (22.1 to 26.0) TIC 2 NH 1 / 9
3.5/5.5 (12/10)
M4 R5.5-4 12.2 to 14 (10.4 to 12.1) TIC 5.5 NH 1 / 9
M5 R5.5-5 20.4 to 24 (17.7 to 20.8) TIC 5.5 NH 1 / 9
M6 R5.5-6 25.5 to 30.0 (22.1 to 26.0) TIC 5.5 NH 1 / 9
M8 R5.5-8 61.2 to 66.0 (53.0 to 57.2) TIC 5.5 NH 1 / 9
8 (8)
M4 R8-4 12.2 to 14 (10.4 to 12.1) TIC 8 NOP 60
M5 R8-5 20.4 to 24 (17.7 to 20.8) TIC 8 NOP 60
M6 R8-6 25.5 to 30.0 (22.1 to 26.0) TIC 8 NOP 60
M8 R8-8 61.2 to 66.0 (53.0 to 57.2) TIC 8 NOP 60
14 (6)
M4 R14-4 12.2 to 14 (10.4 to 12.1) TIC 14 NH 1 / 9
M5 R14-5 20.4 to 24 (17.7 to 20.8) TIC 14 NH 1 / 9
M6 R14-6 25.5 to 30.0 (22.1 to 26.0) TIC 14 NH 1 / 9
M8 R14-8 61.2 to 66.0 (53.0 to 57.2) TIC 14 NH 1 / 9
22 (4) M6 R22-6 25.5 to 30.0 (22.1 to 26.0) TIC 22 NOP 60/ 150H
M8 R22-8 61.2 to 66.0 (53.0 to 57.2) TIC 22 NOP 60/ 150H
30/38 (3 / 2) M6 R38-6 25.5 to 30.0 (22.1 to 26.0) TIC 38 NOP 60/ 150H
M8 R38-8 61.2 to 66.0 (53.0 to 57.2) TIC 38 NOP 60/ 150H
50 / 60
(1 / 1/ 0) M8 R60-8 61.2 to 66.0 (53.0 to 57.2) TIC 60 NOP 60/ 150H
M10 R60-10 102 to 120 (88.5 to 104) TIC 60 NOP 150H
70 (2/0) M8 R70-8 61.2 to 66.0 (53.0 to 57.2) TIC 60 NOP 150H
M10 R70-10 102 to 120 (88.5 to 104) TIC 60 NOP 150H
80 (3/0) M10 R80-10 102 to 120 (88.5 to 104) TIC 80 NOP 150H
M16 R80-16 255 to 280 (221 to 243) TIC 80 NOP 150H
100 (4/0) M10 R100-10 102 to 120 (88.5 to 104) TIC 100 NOP 150H M12 R100-12 143 to 157 (124 to 136) TIC 100 NOP 150H
M16 R80-16 255 to 280 (221 to 243) TIC 80 NOP 150H

7
3.2 Wiring the periphery devices of A510
電源
無熔絲開關 NFB
(及漏電斷路器)
電磁接觸器
AC 電抗器
輸入側雜訊
濾波器
變頻器
零相雜訊濾波器
三相感應
馬達
外加高速保險絲
■No fuse breaker (NFB) and Leakage Circuit Breaker
‧
Please refer to table 3 for choosing NFB of appropriate
current.
‧Do not use NFB to control the start/stop of the inverter.
‧
If a leakage circuit breaker is added for leakage
protection, its current sensitivity shall be more than
200mA and action time more than 0.1 (V-TYPE),
so as
to avoid high-frequency malfunction.
■Electromagnetic contactor
‧It can not add the electromagnetic contactor
for general
use. However, for the application requiring
external
sequence control or automatic restart function after
power cut, an electromagnetic contactor is required.
‧Please
avoid using electromagnetic contactor for the
start/stop control of the inverter as possible.
■AC reactor
‧In case of further improving
the power factor or suppress
the external surge, an AC reactor can be
additionally
equipped.
■Fast acting fuse
‧To protect interface devices, it is necessary to
add a fast
acting fuse (fuse specification will be referred to Section
6.6 in completed manual.)
■Input Noise filter
‧A510 is matched with TECO special filter, meeting the EN
55011 class A criterion.
‧The selection of input noise filter can be referred to
Section 6.4 in completed manual.)
■Inverter
‧Terminal R,S,T at input side have no phase sequence
requirement, thus they can be arbitrarily exchanged.
‧Terminal E must be well grounded.
■Zero-phase noise filter
‧Adding a zero-
phase noise filter at the output side of the
inverter can decrease the
radiated interference and
induced noise.
‧Please refer to Section 6.5 in completed manual.
■Motor
‧
If an inverter drives multiple motors, the rated current of
the inverter must be greater than the total
current that all
motors operate at the same time.
‧Motor and inverter must be grounded respectively.
Power supply
No Fuse Breaker
(NFB) and Leakage
Circuit Breaker
Leakage Circuit
Electromagnetic
contactor
AC reactor
Fast acting fuse
Input Noise filter
Inverter
Zero-phase
noise filter
3-phase
induction
motor

8
3.3 Wiring
The following is the standard wiring diagram for the A510 inverter ( indicates main◎
circuit terminal, ○ indicates control circuit terminal ). Locations and symbols of the wiring
terminal block might be different due to different models of A510. The description of main
circuit terminal and control circuit terminal can be referred to table 1 and 2.
MCNFB
外加高速保險絲
B1/P B2
煞車電阻
R/L1
S/L2
S1
S2
S8
S7
S6
S5
S4
S3
類比輸出1
多
機
能
接
點
輸
入
24V 數位信號電源端子
24VG
數位信號共同端子
故障重置
正向運轉/停止
多段速指令1
寸動指令
外部Base block
Source(PNP)
SW3
AO1
AO2
GND
E
CN3
類比輸出2
E
T/L3
U/T1
V/T2
W/T3
CN6 (RJ45) 1
2
脈波指令輸入
遮蔽線連接端子
GND 類比信號共同端子
E
+12V 類比輸入用電源
AI1 多機能類比輸入
(-10~10V/0~10V, 20K
AI2 多機能類比輸入
P
PDO2
DOG
S(+)
S(-)
PI PO
-12V 類比輸入用電源
P
P
IM
R2C
R1A
R1B
R1C
R2A
F1
F2 安全輸入接點
+12V, 20mA
(-10~10V/0~10V/4~20mA, 250
32K Hz. Max.
I , 出廠設定
SW2
主迴路電源
出
廠
設
定
外
部
類
比
輸
入
-10V~0~10V
4~20mA/0~10V
0V
Sink(NPN), 出廠設定
脈波輸入
反向運轉/停止
UP/增頻率命令
DOWN/減頻率命令
第三種接地
電阻值100 以下
類比信號輸出1, 2
(DC 0~10V)
選購擴充卡(PG卡)
多機能繼電器輸出
250VAC, 1A以下
30VDC, 1A以下
多機能光耦輸出
(DC 48V/50mA, Open Collector)
多機能脈波輸出
32k z. Max.
GND
RS485通訊埠
DO1
表隔離線, 表雙絞芯隔離絞線
P
端子符號 表示主迴路, 表示
控制迴路
*2
*1
*3
*5
*6
*5
*1：僅220V 1~25HP與440V 1~30HP(含)以下容量內建剎晶體機種主回路提供B2端子，可直接於B1, B2間連接煞車電阻。
備註說明：
*2：多機能數位輸入接點S1~S8，可透過開關SW3設置成Source(PNP)或Sink(NPN)模式。
*3：多機能類比輸入2(AI2)，可透過開關SW3設置成電壓命令輸入(0~10V/-10~10V)或電流命令輸入(4~20mA)。
*4
*4：安全輸入接點F1, F2間需短接變頻器始可正常輸出，使用安全輸入時，請務必拆下F1-F2間的短接線。
*5：僅220V 3HP與440V 5HP(含)以上機種，提供-12V, R2A-R2C與PO-GND端子。
*6：僅220V 2HP與440V 3HP(含)以下機種，提供DO2端子。
*5
Braking resistor
Fast acting fuse
Main circuit power
Default setting
Forward rotation/stop
Reversal rotation/stop
Up
Down command
Multi-step speed
command
1
Fault
reset
Jog command
External base block
Multi-function input
D
efault setting
Analog output 1
Analog output 2
The third type grounding.
Resistance lower than 100
ohm.
Analog signal output 1, 2
Option Card (PG)
Multi-function relay output
Power terminal of digital signal
250VAC, under 1A
30VDC, under 1A
Multi-function pulse output
RS485 Communication port
Multi
-
function
photocoupler output
AI1 Multi-function analog input
(-10~10V/0~10V, 20KΩ)
AI2 Multi-function analog input
(-10~10V/0~10V/4~20mA, 250Ω) Default
setting
Safety input contact
GND
Mutual terminal of analog signal
-12V Power of analog input
+12V Power of analog input, +12v,20mA
PI Pulse command input 32K Hz.
Max.
Pulse input
External analog input
Connection terminal of shielding wire
24VG Mutual terminal of digital signal
Means Isolated twisted twire
Means
isolated
wire
Terminal symbol ◎indicates main circuit，
○indicates control circuit
Remark:
*1: Only the master circuit of 220V1~25HP and 440 V1~30HP (included) or models of lower capacity with built-in braking resistor provide terminal B2.
The braking resistor can be connected directly between B1 and B2.
*2: The multi-function digital input terminals S1~S8 can be set to Source (PNP) or Sink (NPN) mode through the SW3.
*3: Multi-function analog input 2 (AI2) can be set to the voltage command input (0-10/-10-10v) or the current command input (4~20mA) through the
SW3.
*4: Safety input connector F1 and F2 should be shorted so that the inverter outputs properly. When the safety input is used, please be sure to remove
the short-pin between F1 and F2.
*5: Only 220 V 3HP and 440 v 5HP (included) or models above, provide terminals -12V, R2A-R2C and PO-GND.
*6. Only 220 V 2HP and 440 v 3HP (included) or models below, provide terminal DO2.

9
3.4 Terminal Description
Table 1 Major Circuit Terminals
Terminal mark
220V: 1~25HP
440V: 1~30HP 220V: 30~100HP 440V: 40~215HP
R/L1 Power supply of th
e main terminal ( single phase, only connect
R-S)
S/L2
T/L3
B1／P •B1／P－: DC power
supply
•B1／P－B2: externally
connected braking resistor
-
B2
•⊕-: DC power supply
or connect
braking detection
module
⊕-
U/T1 Inverter output
V/T2
W/T3
E Grounding terminal (the third type grounding)
Table 2 Main circuit terminals
Type Terminal
terminal function Signal level
Digital
input
signal
S1 Forward rotation─stop command (default),
multi-function input terminals * 1
24 VDC, 8 mA
opto-coupler isolation
(maximum voltage of 30
Vdc, input impedance of
9.03kΩoptocoupler)
S2 Reversal rotation- stop command (default),
multi-function input terminals * 1
S3 UP increases command(default),
multi-function input terminals * 1
S4 DOWN reduces command(default),
multi-function input terminals * 1
S5 Multi-step speed frequency command 1,
multi-function input terminal* 1
S6 fault reset input, multi-function input terminal *
1
S7 JOG frequency command, multi-function input
terminal * 1
S8 External B.B.(Base Block) input,
multi-function input terminal * 1
24V
Power
supply
24V Digital signal SOURCE sharing point (SW3
switched to SOURCE ) ±15%,
Maximum output
current: 250mA( the sum
of all load )
24VG Common terminal of Digital signals Common point of digital signal SINK ( SW3
switched to SINK )

10
Type Terminal
terminal function Signal level
Analog
input
signal
+12V Power for speed setting +12V
( Maximum current , 20mA)
-12V Only above 220V 3HP/ 440V 5HP (include)
support this terminal function -12V (Maximum current, 20mA)
AI1 Voltage mastering speed command (0-10V
input)/(-10V~10V input)
From 0 to +10V,
From -10V to +10V
(Input impedance
: 20KΩ)
(11bit + 1 symbol,
resolution)
AI2 Multi-function analog input terminals *2, can use SW2 to switch voltage or current input
(0~10V)/(4-20mA)
From 0 to +10V,
From -10V to +10V
(Input impedance: 20KΩ)
From 4 to 20 mA
(Input impedance: 250KΩ)
(11bit + 1 symbol,
resolution)
GND Analog signals sharing terminal ----
E Shielding wire’s connecting terminal (Ground)
----
Analog
output
signal
AO1 Multi-
function analog output terminals *3
(0~10V output) From 0 to 10V,
( Maximum current, 20mA )
(PWM 10KHz resolution )
AO2 Multi-
function analog output terminals *3
(0~10V output)
GND Analog signals sharing terminal
Pulse
output
signal
PO
Pulse output, BW 32KHz, only above 220V
3HP/ 440V 5HP (include)
support this
terminal function.
32KHz(max), +12V output
(load: 2.2kΩ)
GND Analog signals sharing terminal ----
Pulse
input
signal
PI
Pulse command input, frequency width of
32KHz
L: from 0.0 to 0.5V
H: from 4.0 to 13.2V
0 - 32 KHz(max)
(impedance:3.89 KΩ)
GND Analog signals sharing terminal ----
Digital
output
DO1 Multi-function(open collector resistor) output:
in operation, zero speed, frequency
consistency, consistency at any frequency,
output frequency , preparation completion,
low-voltage detection, output breaker,
rotation and frequency command,
over-torque detection, abnormal, low-voltage,
Overheat, motor overload, inverter overload,
retrying, communication error, timing
functional output device……
48Vdc, 2~50mA
Opto-coupling output
DO2
(F1 only)
DOG Sharing terminal of the
open collector
transistor

11
Type Terminal
terminal function Signal level
Relay
output
R1A Relay A contact (multi-function output
terminal)
Relay B contact (multi-function output
terminal)
Relay common terminal,
With the same function as DO1/DO2
Terminal capacity:
at 250Vac, 10 mA~1A
at 30Vdc, 10 mA~1A
R1B
R1C
R2A-R2C
(above
F2) With the same function as DO1/DO2 Terminal capacity:
at 250Vac, 10 mA~1A
at 30Vdc, 10 mA~1A
safety
input F1
on: free rotation with safe input
off: general rotation
(i
f use external safety switch to stop, you
must remove the short circuit pin.)
24Vdc, 8mA, pull-high
F2 Safety command common terminal 24V Ground
RS-485
port S (+) RS485/MODBUS Opto-coupler isolation,
differential input and output
S (-)
Grounding
E (G) Grounding to earth
Shield the connecting terminal ----
*1:Multi-function digital input can be referred to the manual.
*2:Multi-function analog input can be referred to the manual.
*3:Multi-function analog output can be referred to the manual.
Caution
‧ Maximum output current capacity of the terminal 12V is 20mA.
‧ Multi-function analog output AO1 and AO2 are special for the analog output of
meter. Please don’t use them to the analog signal output of feedback control.
‧ Control board’s 24V & ±12V just been used for internal control, please don’t connect
to external other devices to use.

12
3.5 Overall Dimension drawing
3.5.1 Standard Model
(a) 220V :1-5HP/440V :1-7.5HP
Inverter Model
Dimension (mm)
W H D W1 H1 t d GW(kg)
Reactor
A510-2001-H
130 215 150 118 203 5 M5 2.2
with option
DCL
A510-2002-H
130 215 150 118 203 5 M5 2.2
A510-2003-H
140 279 177 122 267 7 M5 3.8
A510-2005-H3
140 279 177 122 267 7 M5 3.8
A510-4001-H3
130 215 150 118 203 5 M5 2.2
A510-4002-H3
130 215 150 118 203 5 M5 2.2
A510-4003-H3
130 215 150 118 203 5 M5 2.2
A510-4005-H3
140 279 177 122 267 7 M5 3.8
A510-4008-H3
140 279 177 122 267 7 M5 3.8
(b) 220V :7.5-25HP/440V :10-30HP

13
Inverter Model
Dimension (mm)
W H D W1 H1 t d GW(kg)
Reactor
A510-2008-H3
210 300 215 192 286 1.6 M6 6.2
with option
ACL
A510-2010-H3
210 300 215 192 286 1.6 M6 6.2
A510-2015-H3
265 360 225 245 340 1.6 M6 10
A510-2020-H3
265 360 225 245 340 1.6 M6 10
A510-2025-H3
265 360 225 245 340 1.6 M6 10
A510-4010-H3
210 300 215 192 286 1.6 M6 6.2
A510-4015-H3
210 300 215 192 286 1.6 M6 6.2
A510-4020-H3
265 360 225 245 340 1.6 M6 10
A510-4025-H3
265 360 225 245 340 1.6 M6 10
A510-4030-H3
265 360 225 245 340 1.6 M6 10
(c) 220V :30-40HP/440V :40-60HP
Inverter Model
Dimension (mm)
W H D W1 H1 t d GW(kg)
Reactor
A510-2030-H3
284 525 252 220 505 1.6 M8 30
with option
ACL
A510-2040-H3
284 525 252 220 505 1.6 M8 30
A510-4040-H3
284 525 252 220 505 1.6 M8 30
A510-4050-H3
284 525 252 220 505 1.6 M8 30
A510-4060-H3
284 525 252 220 505 1.6 M8 30

14
(d) 220V :50-100HP/440V :75-215HP(IP00)
Inverter Model
Dimension (mm)
W H D W1 H1 t d GW(kg)
Reactor
A510-2050-H3
344 580 300 250 560 1.6 M8 40.5
DCL
STANDARD
INCLUDED
A510-2060-H3
344 580 300 250 560 1.6 M8 40.5
A510-2075-H3
459 790 324.5
320 760 1.6 M10 74
A510-2100-H3
459 790 324.5
320 760 1.6 M10 74
A510-4075-H3
344 580 300 250 560 1.6 M8 40.5
A510-4100-H3
344 580 300 250 560 1.6 M8 40.5
A510-4125-H3
459 790 324.5
320 760 1.6 M10 74
A510-4150-H3
459 790 324.5
320 760 1.6 M10 74
A510-4175-H3
459 790 324.5
320 760 1.6 M10 74
A510-4215-H3
459 790 324.5
320 760 1.6 M10 74

15
(e) 220V :50-100HP/440V :75-215HP(IP20)
Inverter Model
Dimension (mm)
W H D W1 H1 t d GW(kg)
Reactor
A510-2050-H3
348.5
740 300 250 560 1.6 M8 44
DCL
STANDARD
INCLUDED
A510-2060-H3
348.5
740 300 250 560 1.6 M8 44
A510-2075-H3
463.5
1105
324.5
320 760 1.6 M10 81
A510-2100-H3
463.5
1105
324.5
320 760 1.6 M10 81
A510-4075-H3
348.5
740 300 250 560 1.6 M8 44
A510-4100-H3
348.5
740 300 250 560 1.6 M8 44
A510-4125-H3
463.5
1105
324.5
320 760 1.6 M10 81
A510-4150-H3
463.5
1105
324.5
320 760 1.6 M10 81
A510-4175-H3
463.5
1105
324.5
320 760 1.6 M10 81
A510-4215-H3
463.5
1105
324.5
320 760 1.6 M10 81
Note: 250HP or above are being developed

16
3.5.2 Built-in filter model (440V 1~60HP)
(a) 440V :1-7.5HP
Inverter Model
Dimension (mm)
W H D W1 H1 H2 t d GW(kg)
Reactor
A510-4001-H3F
130
265
150
118
203
215
5 M5 2.83
with option
ACL
A510-4002-H3F
130
265
150
118
203
215
5 M5 2.83
A510-4003-H3F
130
265
150
118
203
215
5 M5 2.83
A510-4005-H3F
140
349
177
124
266
279
7 M5 4.72
A510-4008-H3F
140
349
177
124
266
279
7 M5 4.72
(b) 440V :10-30HP
Inverter Model
Dimension (mm)
W H D W1 H1 H2 t d GW(kg)
Reactor
A510-4010-H3F
210
385
215
192
286
300
1.6 M6 7.72
with option
DCL
A510-4015-H3F
210
385
215
192
286
300
1.6 M6 7.72
A510-4020-H3F
265
480
225
245
340
360
1.6 M6 11.6
A510-4025-H3F
265
480
225
245
340
360
1.6 M6 11.6
A510-4030-H3F
265
480
225
245
340
360
1.6 M6 11.6

17
(c) 440V :40-60HP
Inverter Model
Dimension (mm)
W H D W1 H1 H2 t d GW(kg)
Reactor
A510-4040-H3F
284
695
252
220
505
525
1.6 M8 32.24 with option
ACL
A510-4050-H3F
284
695
252
220
505
525
1.6 M8 32.24
A510-4060-H3F
284
695
252
220
505
525
1.6 M8 32.24

18
Chapter 4 Software Index
4.1 Keypad Description
4.1.1 Panel Functions
Type Name Functions
Display
Main display area Display frequency, parameter voltage, current, temperature and
abnormity and ect.
LED status display
FAULT: When the inverter has a warning or fault message, the
indicator lights up.
FWD: When the inverter is in forward rotation status, the
indicator lights up.
(long bright light while inverter running, flicker while
inverter stopping)
REV: When the inverter is in reversal rotation status, the
indicator lights up.
(long bright light while inverter running, flicker while
inverter stopping)
SEQ: When inverter’s run command source is set to external
control, the indicator lights up.
REF: When inverter’s frequency command source is set to
external control, the indicator lights up.
Keys
（
（（
（8 keys）
））
）
RUN RUN: Enable the inverter run operation.
STOP STOP: Enable the inverter stop operation.
▲It is used for frequency and parameter setting.
▼It is used for frequency and parameter setting.
FWD/REV
This key is used for switching motor’s rotation direction. FWD
indicator on means the motor is rotating in forward direction;
REV indicator on means the motor is rotating in reversal
direction.
DSP/FUN It is use for switching dispay interface, based on the loop of
frequency screen function selectionmonitor parameter
frequency screen.