TECO L510S Series User manual

I
L510s manual
Table of Contents
Chapter 0 Preface…………………………………………………………... 0-1
0.1 Preface……………………………………………………….
0-1
Chapter 1 Safety Precautions……………………………………………. 1-1
1.1 Before Power UP…………………………………………… 1-1
1.2 During Power UP…………………………………………… 1-1
1.3 Before Operation……………………………………………
1-2
1.4 During Operation…………………………………………… 1-2
1.5 Inverter Disposal……………………………………………. 1-2
Chapter 2 Part Number Definition……………………………………….. 2-1
2.1 Model part number…………………………………………. 2-1
2.2 Standard Product Specification…………………………… 2-2
Chapter 3 Environment & Installation………………………………...... 3-1
3.1 Environment…………………………………………………
3-1
3.2 Installation……………………………………………………
3-3
3.2.1 Installation methods…………………………………… 3-3
3.2.2 Installation space……………………………………… 3-6
3.2.3 De-rating curve………………………………………… 3-9
3.2.4 Capacitor reforming Guide after long storage……… 3-10
3.3 Wiring guidelines…………………………………………… 3-11
3.3.1 Main Considerations........................………………... 3-11
3.3.2 Power cables…………………................................... 3-12
3.3.3 Control cable selection and wiring…….…………….. 3-12
3.3.4 Wiring and EMC guidelines…………….……………. 3-13
3.3.5 Failure liability…………………………………………. 3-14
3.3.6 Considerations for peripheral equipment…………... 3-15
3.3.7 Ground connection…………………………………... 3-16
3.4 Specifications………………………………………………..
3-17
3.4.1 Product Specifications………………………………... 3-17
3.4.2 General Specifications……………………………….. 3-19
3.5 Standard wiring…………………………………………….. 3-21
3.5.1 Single phase(NPN) input……………………………... 3-21
3.5.2 Single phase(PNP) input……………………………... 3-22
3.5.3 Three phase(NPN) input……………………………... 3-23
3.5.4 Three phase(PNP) input……………………………… 3-24
3.5.5 NPN/PNP selectable models………………………… 3-25
3.5.6 Single / Multi-Pump Dedicated Wiring Diagram (When 14-00=1)……………………………..………… 3-26
3.6 Terminal Description……………………………………….. 3-28
3.6.1 Description of main circuit terminals………………… 3-28
3.6.2 Description of control circuit terminals……………… 3-29

II
3.7 Outline Dimensions………………………………………… 3-31
3.8 EMC filter Disconnection…………………………………... 3-36
Chapter 4 Software Index…………………………………………………. 4-1
4.1 Keypad Description ……………………………………….. 4-1
4.1.1 Operator Panel Functions……………………………. 4-1
4.1.2 Digital Display Description........................................ 4-2
4.1.3 Digital Display Setup…………………………………. 4-4
4.1.4 Example of Keypad Operation ……………………… 4-6
4.1.5 Operation Control……………………………………... 4-8
4.2 Programmable Parameter Groups……………………….. 4-9
4.3 Parameter Function Description…………………………. 4-29
Chapter 5 Troubleshooting and Maintenance………………………… 5-1
5.1 Error Display and Corrective Action……………………… 5-1
5.1.1 Manual Reset and Auto-Reset………………………. 5-1
5.1.2 Keypad Operation Error Instruction…………………. 5-4
5.1.3 Special conditions…………………………………….. 5-5
5.2 General troubleshooting…………………………………… 5-6
5.3 Troubleshooting of the inverter…………………………… 5-7
5.3.1 Quick troubleshooting of the inverter………………... 5-7
5.3.2 Troubleshooting for OC, OL error displays…………. 5-9
5.3.3 Troubleshooting for OV, LV error……………………. 5-10
5.3.4 The Motor can not run………………………………… 5-11
5.3.5 Motor Overheating…………………………………….. 5-12
5.3.6 Motor runs unbalanced……………………………….. 5-13
5.4 Routine and periodic inspection………………………….. 5-14
5.5 Maintenance…………………………………………………
5-15
Chapter 6 Peripheral Components……………………………………… 6-1
6.1 Reactor Specifications…………………………………….. 6-1
6.2 Electromagnetic Contactor & No fuse circuit breaker….. 6-1
6.2.1 EMC External Filter (C2 Level)……………….……... 6-1
6.3 Fuse Specification………………………………………….. 6-2
6.4 Fuse Specification(UL Model Recommended)………….. 6-2
6.5 Braking Resistor……………………………………………. 6-3
6.6 Copy Unit(JN5-CU)……….………………………..……… 6-3
6.7 Communication option….……………….………………… 6-4
6.8 RJ45 to USB connecting Cable (1.8m)……….………… 6-4
Appendix 1 L510 Parameters Setting List……………………………….. App1-1
Appendix 2 Instructions for UL……………………………………………. App2-1
Appendix 3 L510 MODBUS Communication protocol…………………. App3-1
Appendix 4 JN5-CM-USB instruction manual…………………………… App4-1
Appendix 5 510 series accessories manual…………………………….. App5-1

0-1
Chapter 0 Preface
0.1 Preface
To extend the performance of the product and ensure personnel safety, please read
this manual thoroughly before using the inverter. Should there be any problem in
using the product that cannot be solved with the information provided in the manual,
contact our technical or sales representative who will be willing to help you.
※Precautions
The inverter is an electrical product. For your safety, there are symbols such as
“Danger”, “Caution” in this manual as a reminder to pay attention to safety
instructions on handling, installing, operating, and checking the inverter. Be sure to
follow the instructions for highest safety.
Danger Indicates a potential hazard that could cause death or serious
personal injury if misused.
Caution Indicates that the inverter or the mechanical system might be damaged
if misused.
Danger
Risk of electric shock. The DC link capacitors remain charged for five
minutes after power has been removed. It is not permissible to open the
equipment until 5 minutes after the power has been removed.
Do not make any connections when the inverter is powered on. Do not check
parts and signals on circuit boards during the inverter operation.
Do not disassemble the inverter or modify any internal wires, circuits, or
parts.
Ensure that the Inveter Ground terminal is connected correctly.
Caution
Do not perform a voltage test on parts inside the inverter. High voltage can
destroy the semiconductor components.
Do not connect T1, T2, and T3 terminals of the inverter to any AC input
power supply.
CMOS ICs on the inverter’s main board are susceptible to static electricity. Do
not touch the main circuit board.

1-1
Chapter 1 Safety Precautions
1.1 Before Power Up
Danger
Make sure the main circuit connections are correct. Single phase L1(L),L3(N), and Three
phase L1(L),L2,L3(N); 400V : L1,L2,L3 are power-input terminals and must not be mistaken for
T1,T2 and T3. Otherwise, inverter damage can result.
Caution
The line voltage applied must comply with the inverter’s specified input voltage.(See the
nameplate)
To avoid the front cover from disengaging, or other damge do not carry the inverter by its
covers. Support the drive by the heat sink when transporting. Improper handling can damage
the inverter or injure personnel and should be avoided.
To avoid the risk of fire, do not install the inverter on a flammable object. Install on
nonflammable objects such as metal.
If several inverters are placed in the same control panel, provide heat removal means to
maintain the temperature below 50 degree C to avoid overheat or fire.
When disconnecting the remote keypad, turn the power off first to avoid any damage to the
keypad or the inverter.
Installation limitation, -10~50℃ (cooling fan inside model), -10~40℃ (without cooling fan
inside model)
Warning
This product is sold subject to EN 61800-3 and EN 61800-5-1.
In a domestic environment this product may cause radio interference in which
case the user may be required to apply corrective measures.
Caution
Work on the device/system by unqualified personnel or failure to comply with warnings can
result in severe personal injury or serious damage to material. Only suitably qualified
personnel trained in the setup, installation, commissioning and operation of the product should
carry out work on the device/system.
Only permanently-wired input power connections are allowed.
1.2 During Power Up
Danger
When the momentary power loss is longer than 2 seconds, the inverter will not have sufficient
stored power for its control circuit. Therefore, when the power is re-applied, the run operation
of the inverter will be based on the setup of following parameters:
Run parameters. 00-02 or 00-03.
Direct run on power up. Parameter. 07-04 and the status of external run switch,
Note-: the start operation will be regardless of the settings for parameters
07-00/07-01/07-02.
Danger. Direct run on power up.
If direct run on power up is enabled and inverter is set to external run
with the run FWD/REV switch closed then the inverter will restart.
Danger
Prior to use, ensure that all risks and safety implications are considered.

1-2
When the momentary power loss ride through is selected and the power loss is short, the
inverter will have sufficient stored power for its control circuits to function, therefore, when the
power is resumed the inverter will automatically
restart depending on the setup of parameters 07-00 & 07-01.
1.3 Before Operation
Caution
Make sure the model and inverter capacity are the same as that set in parameter 13-00.
Note : On power up the supply voltage set in parameter 01-01 will flash on display
for 2 seconds.
1.4 During Operation
Danger
Do not connect or disconnect the motor during operation. Otherwise, It may cause the inverter
to trip or damage the unit.
Danger
To avoid electric shock, do not take the front cover off while power is on.
The motor will restart automatically after stop when auto-restart function is enabled. In this
case, care must be taken while working around the drive and associated equipment .
The operation of the stop switch is different than that of the emergency stop switch. The stop
switch has to be activated to be effective. Emergency stop has to be de-activated to become
effective.
Caution
Do not touch heat radiating components such as heat sinks and brake resistors.
The inverter can drive the motor from low speed to high speed. Verify the allowable speed
ranges of the motor and the associated machinery.
Note the settings related to the braking unit.
Risk of electric shock. The DC link capacitors remain charged for five minutes after power has
been removed. It is not permissible to open the equipment until 5 minutes after the power has
been removed.
Caution
The Inverter should be used in environments with temperature range from (14-104℉) or (-10
to 40℃) and relative humidity of 95%.
Note: models with fan : -10~50℃, models without fan : -10~40℃
Danger
Make sure that the power is switched off before disassembling or checking any components.
1.5 Inverter Disposal
Caution
Please dispose of this unit with care as an industrial waste and according to your required local
regulations.
The capacitors of inverter main circuit and printed circuit board are considered as hazardous
waste and must not be burnt.
The Plastic enclosure and parts of the inverter such as the cover board will release harmful
gases if burnt.

2-1
Chapter 2 Part Number Definition
2.1 Model Part Number
Note：
1. 102/1P5/101/2P2/2P5/201/202/203/401/402/403 models need to select digital input type
by code⑦(NPN or PNP input).
2. 205/208/210/405/408/410/415 models need to select digital input type by control terminal,
please refer the wiring diagram of chapter 3.
3. If the pump parallel connection is necessary, please select the model of pump application by
code⑧.
4. Standard type: Built-in BACnet communication, without PUMP parallel function.
PUMP type: Built-in PUMP parallel function, without BACnet communication.

2-2
2.2 Standard Product Specification
Model Supply Voltage
(Vac)
Frequency
(Hz) (HP) (KW) Model Filter
NPN PNP Built-in None
L510-1P2-SH1-N 1ph,
100~120V
+10%/-15%
50/60Hz
0.25 0.2 ◎ ◎
L510-1P5-SH1-N 0.5 0.4 ◎ ◎
L510-101-SH1-N 1 0.75 ◎ ◎
L510-2P2-SH1F-P
1ph,
200~240V
+10%/-15%
0.25 0.2 ◎ ◎
L510-2P5-SH1F-P 0.5 0.4 ◎ ◎
L510-2P7-SH1F-P 0.75 0.55 ◎ ◎
L510-201-SH1F-P 1 0.75 ◎ ◎
L510-202-SH1F-P 2 1.5 ◎ ◎
L510-203-SH1F-P 3 2.2 ◎ ◎
L510-2P2-SH1-N 0.25 0.2 ◎ ◎
L510-2P5-SH1-N 0.5 0.4 ◎ ◎
L510-2P7-SH1-N 0.75 0.55 ◎ ◎
L510-201-SH1-N 1 0.75 ◎ ◎
L510-202-SH1-N 2 1.5 ◎ ◎
L510-203-SH1-N 3 2.2 ◎ ◎
L510-2P2-SH3-N
3ph,
200~240V
+10%/-15%
0.25 0.2 ◎ ◎
L510-2P5-SH3-N 0.5 0.4 ◎ ◎
L510-201-SH3-N 1 0.75 ◎ ◎
L510-202-SH3-N 2 1.5 ◎ ◎
L510-203-SH3-N 3 2.2 ◎ ◎
L510-205-SH3 5 3.7 ◎ ◎ ◎
L510-208-SH3 8 5.5 ◎ ◎ ◎
L510-210-SH3 10 7.5 ◎ ◎ ◎
L510-401-SH3-N
3ph,
380~480V
+10%/-15% 50/60Hz
1 0.75 ◎ ◎
L510-402-SH3-N 2 1.5 ◎ ◎
L510-403-SH3-N 3 2.2 ◎ ◎
L510-401-SH3F-P 1 0.75 ◎ ◎
L510-402-SH3F-P 2 1.5 ◎ ◎
L510-403-SH3F-P 3 2.2 ◎ ◎
L510-405-SH3 5 3.7 ◎◎ ◎
L510-408-SH3 8 5.5 ◎◎ ◎
L510-410-SH3 10 7.5 ◎◎ ◎
L510-415-SH3 15 11 ◎◎ ◎
L510-405-SH3F 05 3.7 ◎◎◎
L510-408-SH3F 08 5.5 ◎◎◎
L510-410-SH3F 10 7.5 ◎◎◎
L510-415-SH3F 15 11 ◎◎◎
Short circuit capacity is below 5000A/120V or 5000A/240V or 5000A/480V, for 100~120V models is
120V; 200~240V models is 240V, 380~480V models is 480V.

2-3
Model
(Built-in PUMP
Parallel Function)
Supply
voltage(Vac) Frequency (Hz) (Hp) (KW) Digital input
model Filter
NPN PNP NPN PNP
L510-1P2-SH1-NP 1ph，
100~120V
+10%/-15%
50/60Hz
0.25 0.2 ◎◎
L510-1P5-SH1-NP 0.5 0.4 ◎◎
L510-101-SH1-NP 1 0.75 ◎◎
L510-2P2-SH1F-PP
1ph，
200~240V
+10%/-15%
0.25 0.2 ◎◎
L510-2P5-SH1F-PP 0.5 0.4 ◎◎
L510-2P7-SH1F-PP 0.75 0.55 ◎ ◎
L510-201-SH1F-PP 1 0.75 ◎◎
L510-202-SH1F-PP 2 1.5 ◎◎
L510-203-SH1F-PP 3 2.2 ◎◎
L510-2P2-SH1-NP 0.25 0.2 ◎◎
L510-2P5-SH1-NP 0.5 0.4 ◎◎
L510-2P7-SH1-NP 0.75 0.55 ◎ ◎
L510-201-SH1-NP 1 0.75 ◎◎
L510-202-SH1-NP 2 1.5 ◎◎
L510-203-SH1-NP 3 2.2 ◎◎
L510-2P2-SH3-NP
3ph，
200~240V
+10%/-15%
0.25 0.2 ◎◎
L510-2P5-SH3-NP 0.5 0.4 ◎◎
L510-201-SH3-NP 1 0.75 ◎◎
L510-202-SH3-NP 2 1.5 ◎◎
L510-203-SH3-NP 3 2.2 ◎◎
L510-205-SH3P 5 3.7 ◎ ◎ ◎
L510-208-SH3P 8 5.5 ◎ ◎ ◎
L510-210-SH3P 10 7.5 ◎ ◎ ◎
L510-401-SH3-NP
3ph，
380~480V
+10%/-15% 50/60Hz
1 0.75 ◎ ◎
L510-402-SH3-NP 2 1.5 ◎ ◎
L510-403-SH3-NP 3 2.2 ◎ ◎
L510-401-SH3F-PP 1 0.75 ◎◎
L510-402-SH3F-PP 2 1.5 ◎◎
L510-403-SH3F-PP 3 2.2 ◎◎
L510-405-SH3P 5 3.7 ◎ ◎ ◎
L510-408-SH3P 8 5.5 ◎ ◎ ◎
L510-410-SH3P 10 7.5 ◎ ◎ ◎
L510-415-SH3P 15 11 ◎ ◎ ◎
L510-405-SH3FP 05 3.7 ◎ ◎ ◎
L510-408-SH3FP 08 5.5 ◎ ◎ ◎
L510-410-SH3FP 10 7.5 ◎ ◎ ◎
L510-415-SH3FP 15 11 ◎ ◎ ◎
Short circuit capacity is below 5000A/120V or 5000A/240V or 5000A/480V, for 100~120V models is
120V; 200~240V models is 240V, 380~480V models is 480V.

3-1
Chapter 3 Environment & Installation
3.1 Environment
Installation environment has a direct effect on the correct operation and the life expectancy of the
inverter, Install the inverter in an environment complying with the following conditions:
Protection
Protection
class IP20 Open Type
Suitable environment
Operating
temperature
-10~40°C (-10~50°C with fan) (non-freezing)
If several inverters are installed in the same control panel, ensure
adequate spacing and provide the necessary cooling and ventilation for
successful operation.
Storage
temperature -20~60°C
Relative
Humidity Max 95% (without condensation)
Altitude
Altitude：Below 1000m (3281ft)
It is required to reduce 2% of inverter
rated current at each additional
100m. The maximum altitude is
3000m
Vibration
Frequency: 10Hz - 150Hz - 10Hz
Amplitude(0.3mm): 10Hz ≦f ≦57Hz
Acceleration(2G): 57Hz ≦f ≦150Hz
(According to IEC60068-2-6 standard)
Installation site
Install in an environment that will not have an adverse effect on the operation of the unit
and ensure that there is no exposure to areas such as that listed below:-
Direct sunlight, Rain or moisture
Oil mist and salt
Dust, lint fibres, small metal filings and corrosive liquid and gas
Electromagnetic interference from sources such as welding equipment
Radioactive and flammable materials
Excessive vibration from machines such as stamping, punching machines
Add vibration-proof pads if necessary

3-2
Product Overview
RS485
port
Operator
Panel
TM2
terminal
TM1
terminal
Ground
terminal
Frame 3 Frame 4
Operator
Panel
RS485
port
TM2
terminal
TM1
terminal
Ground
terminal
Frame 1 Frame 2

3-3
3.2 Installation
3.2.1 Installation methods
Frame1. Mounting on a flat surface.
Din rail type installation：
Din rail kit includes a plastic and a metal adaptor plates.
Assembly Steps:-
1) Attach the metal adaptor plate to the inverter base with the screws provided.
2) Attach the plastic Din rail adaptor to the metal adaptor plate.
3) Push the plastic adaptor forward to lock into position.
Disassembly Steps:-
1) Unlock by pushing the snap hooks
2) Retract and remove the plastic Din rail adaptor.
3) Unscrew the metal plate &Remove
Note：
JN5-DIN-L01 (Frame 1 Din rail kit part number), including the following parts
1. Metal plate adaptor
2. Plastic adaptor
3. Chamfer head screw: M3×6
Screw: M4
1. Metal plate adapto
r
2. Plastic adapto
r
Snap hooks
1. Metal plate adaptor
2. Plastic adapto
r
Snap hooks
3. screws 3. screws
Assembly:- Disassembly:-

3-4
Frame 2. Mounting on a flat surface.
Din rail type installation：
Din rail kit includes a plastic adaptor plate as an attachment for the inverter base.
Refer to Diagram below:-
Din Rail Mounting & Dismounting as shown in the diagram below:-Use a 35mm Din Rail.
Plastic adaptor plate.
JN5-DIN-L02 (Frame 2 Din rail kit part number)
Mounting Dismounting
Assembly:- Disassembly:-
Plastic Adaptor plate
Snap hook
Middle Snap hook
Snap hook
Screw: M4

3-5
Frame 3. Mounting on a flat surface
M4 螺丝
Frame 4. Mounting on a flat surface
M4 螺丝
M4 screw
M4 screw

3-6
3.2.2 Installation space
Provide sufficient air circulation space for cooling as shown in examples below.
Install the Inverter on surfaces that provide good heat dissipation.
Single unit Installation
Install the inverter verticality to obtain effective cooling.
Side by side Installation
5cm5cm
12cm
12cm
Front view
Fan Fan
Side view
Provide the necessary
physical space and cooling
based on the ambient
temperature and the heat
loss in the panel
CONTROL
PANEL
5cm
Fan

3-7
Installation for Grounding kit
Grounding kit：
As bellowed diagram, use screw to install EMC metal plate into heatsink.
Frame 1 Frame 2

3-8
Grounding kit option installation diagram and instruction (Example)
Frame 1 Frame 2
1. Grounding kit to be mounted on the drive (earth casing), please follow the diagram to
install .
2. Unshielded power supply lines or cable.
3. Unshielded wires or cable for the output of the relay contacts.
4. Attach and earth the shielding of cables 3and 4as close as possible to the drive:
Strip the cable to expose the shielding;
Attach the cable to the plate 1, attaching the clamp on the stripped part of the
shielding.
The shielding must clamped tightly enough to metal sheet to ensure good contact.
5. Shielded power supply cable for connecting motor which connect to earth at both
ends. The shielding must be continuous, and if intermediate terminals are used, they
must be placed in EMC shielded metal boxes.
6. Shielded cable for control-signal wiring. For applications requiring several conductors,
use cables with small cross-section (0.5 mm^2, 20 AWG). For cables 3and 4, the
shielding must be connected to earth at both ends. The shielding must be continuous,
and if intermediate terminals are used, they must be placed in EMC shielded metal
boxes.
Notice：
● If using external EMC input filter, it must be mounted under the drive and connected
directly to the line supply via an unshielded cable. Link 6on the drive is then via the
output cable.
● The HF equipotential earth connection between the drive, motor and cable shielding
does not remove the need to connect the PE conductors (green-yellow) to the
appropriate terminals on each device.

3-9
3.2.3 De-rating curve
Curves below show the applicable output current de-rate due to setting of carrier
frequency and the ambient operating temperatures of 40 and 50 degree C.
2P2/2P5/2P7/201 (40℃)1P2/1P5(40℃)、202/203 (50℃)
208(50℃)210(50℃)
401/2/3(50℃) 405(50℃)
408(50℃)410(50℃)

3-10
415(50℃) 101/205(50℃)
100%
5K 10K 16K
Rated Current(In)
Carrier Frequency(Hz)
Note: 101 and 205 type does not need to decrease the current rating in 50 degrees
ambient temperature.
3.2.4 Capacitor reforming Guide after long storage
For correct performance of this product after long storage before use it is important that
Inverter Capacitors are reformed according to the guide below:
Storage
time Procedure to re-apply voltage
≦1year Apply rated voltage(Note1) of inverter in the normal way
Between
1-2 years
Apply rated voltage of inverter to the product for one hour before using
the inverter
≧2 years
Use a variable AC power supply to
1. Connecting 25% rated voltage of inverter for 30 minutes.
2. Connecting 50% rated voltage of inverter for 30 minutes.
3. Connecting 75% rated voltage of inverter for 30 minutes.
4. Connecting 100% rated voltage of inverter for 210 minutes.
Once the procedures completed, inverter just can be used normally.
Note1：Rated voltage: please refer the rated voltage according to model label of inverter.

3-11
3.3 Wiring Guidelines
3.3.1 Main considerations
1 Tightening Torque for Screw terminals：Refer to the tables 3-1, when using a
screwdriver or any other suitable tools to make connections.
2 Power terminals:
Single phase : L1 (L), L3 (N)
Three-phase 200V models: L1 (L), L2, L3 (N)
400V models: L1, L2, L3
3 For all cabling use copper wires and the cable size shall be according to the table
below rated at 105 degrees Celsius.
4 Power & Control cable Minimum rated voltage
240V AC system, 300V AC.
480V AC system, 600V AC.
5 Control cables should be separated from the power cables. Do not place them in the
same cable tray or cable trunking to prevent against electrical interference.
Table 3-1
Frame
size
TM1 TM2
Cable Size Tightening torque Cable Size Tightening torque
AWG mm² kgf.cm Ibf.in Nm AWG mm² kgf.cm Ibf.in Nm
Frame1 22~10 0.34~6 14 12.15 1.37 24~12 0.5~2.5 4.08 3.54 0.4
Frame2 12.24 10.62 1.2
Frame3 18~8 0.82~8.4 18 15.58 1.76 24~12 0.5~2.5 5.1 4.43 0.5
Frame4 14~6 2~13.3 24.48 21.24 2.4
6 The maximum RMS symmetrical Current Ratings and voltage are listed as below:
Device Rating Short circuit Rating Maximum Voltage
voltage HP
110V 0.2~1 5000A 120V
220V 0.2~10 5000A 240V
440V 1~15 5000A 480V
7 Electrical ratings of terminals:
Horsepower Power Specification Voltage (Volt) Current(A)
0.25/0.5/1 220~240V
300
30
1 100~120V 20
2/3 220~240V 30
1/2/3 380~480V 600 28
5 220~240V 300 45
7.5/10 220~240V 300 65
5.5/7.5 380~480V 600 45
10/15 380~480V 600 65