Teknion UNSF User manual

Part and Product Identification
Section:
Description: Page No:
Date:
Rev. No: 1
May 2016 1 of 5
DIS_301a
district
For Customer Support please contact
[email protected]
A1
C2
UNSF
B1
UNSDE
Floor Screen (UNSF) & Desk Edge Screen (UNSDE)
A1 - Floor Screen Sub-Assembly
(N09-1626-X) x1
B1 - Desk Edge Screen
(C05-2703-X) x1
C1 - Desk Edge Screen Bracket
(A25-0449) x1
C2 - Desk Edge Screen Mounting
Plate Sub Assembly
(N09-4959) x1
C3 - #10 x 0.875" Screw. Quad
Pan Washer
(E07-0077) x6
C4 -1/4ID x 1/8OD A 1/8THK
SBR Flat Washer
BLK(SPA315040)
(E03-0582) x4
C5 - 1/4-20x5/8" Machine Screw,
Quad. Truss HD
(E01-0098) x4
C6 - 1/4-20 UNC. Nut Hex Keps
Zinc
(E03-0059) x2
C1
C2
C1
NOTE: Floor Screen(UNSF) instruction is shown as
an example. Brakcet kit(x03-0239) installing method
also applies for Desk Edge Screen(UNSDE)
Bracket Kit (X03-0239) x2 or x4

Section:
Description: Page No:
Date:
INSTALL MOUNTING PLATES ON SCREEN INTALL BRACKETS ON MOUNTING PLATES
DIS_301a
2 of 5
May 2016
district
STEP 1: Place mounting plate align with four holes. Fasten with machine screws, insuring that
washer goes in between the mounting plate and the machine screws.
STEP 2: Gently engage screen mounting plate and the bracket as shown above. Do not fully
tighten the Hex Keps Nut.
C2
C4
C5
A1
C6
A1
NOTE: If two or more screens are
installed side by side, the height is
adjustable to align the screens.

1"
STEP 3: Align Screen with the edge of the Worksurface as shown.
NOTE: Make sure the edge of the Screen is flush with the end of Worksurface. Ensure 1" gap between the edge of Screen and Worksurface.
district
Section:
Description: Page No:
Date:
ALIGN SCREEN
May 2016 3 of 5
DIS_301a
NOTE:
1) Make sure the edge of the Screen is
flush with the end of Worksurface.
2) Ensure 1" gap between the edge
of Screen and Worksurface.

STEP 4: Fasten Brackets under the work surface with screws provided.
districtdistrict
Section:
Description: Page No:
Date:
FASTEN TO UNDERSIDE OF WORKSURFACE
May 2016 4 of 5
DIS_301a
C1
C3

STEP 5: Place the level on the top of the screen. Adjust the screen with leveler by turning to required direction. Turn the Hex Nuts as shown to lock the screen in place.
NOTE: If two or more screens are installed side by side, the height is adjustable to align the screens. After being fully installed.
districtdistrict
Section:
Description: Page No:
Date:
LEVEL SCREEN
May 2016 5 of 5
DIS_301a
NOTE: If two or more
screens are installed side by
side, the height is adjustable
to align the screens. After
being fully installed.
* * If leveling is an
issue for the Floor
Screen, replace
existing levelers with
a Floor Screen
Extended Leveling
Kit (UNSFXL),
ordered seperatly.
* * C6
C1
A1