Teledyne SeaBat T Series User manual

SeaBat T-Series Rackmount
SeaBat T20-R / T50-R - Quick Reference Guide*
Version 2 Document Number QG14832 / Part Number 1008753 24/06/2020
SeaBat T-Series Rackmount
The SeaBat T20-R and T50-R multi-frequency
multibeam sonar systems for surface vessels:
Depth rating: 50m
Frequency: 190-420kHz
Ping rate: Up to 50Hz (range dependent)
Range: Up to 575m (200kHz)
Power requirements: 100-230VAC, 50/60Hz,
up to 390W1max.
Operating temperature wet end: -2°to +36°
Operating temperature dry end: -5° to +45°
Rack-mounted Sonar Processor (RSP)
RSP
Height
88.0mm
Width
478.0mm
Depth
461.6mm
Weight
12.3kg-13.8kg
Sonar interface and processing functions combined
into one unit.
Projector Unit
T20 / T50: TC2181 200-400kHz
Height
86.6mm
Length
280.0mm
Depth
93.1mm
Weight in air
5.4kg
Weight in water
3.4kg
Standard Cables
Projector to RSP
Bend radius
73mm (minimum)
Cable length
T20: 10m
T50: 25m
Receiver to RSP
Bend radius
100mm (minimum)
Cable length
T20: 10m
T50: 25m
Receiver Units
T20: EM7219 200-400kHz
Height
123.2mm
Length
254.0mm
Depth
102.0mm
Weight in air
5.0kg
Weight in water
2.2kg
T50: EM7218 200-400kHz
Height
90.7mm
Length
460.0mm
Depth
102.0mm
Weight in air
8.2kg
Weight in water
3.9kg
Wet-End Brackets
T20
T50
Width
(projector end)
98.0mm
Width
(receiver end)
262.0mm
468.0mm
Depth
391.0mm
Weight in air,
bracket
1.7kg
2.5kg
Weight in air,
bracket + wet end
12.1kg
(excl. cables)
16.1kg
(excl. cables)
* This Quick Reference Guide is not intended as a substitute for the Operator’s Manual (provided on a USB key).
1390W max. is for the INS configuration with dual head.

SeaBat T-Series Rackmount
SeaBat T20-R / T50-R - Quick Reference Guide*
Version 2 Document Number QG14832 / Part Number 1008753 24/06/2020
System Block Diagram
Online SV input Time
synchronization Additional
sensors
Motion
TC2181
200-400kHz projector(s)
EM7218 or EM7219
200-400kHz receiver(s)
Rack-mounted
Sonar Processor
(RSP)
CFE Ethernet NAS
CFE laptop/PC
100-230VAC
IMU*
Antennas* * IMU and antennas are included in the
optional int ernal INS configuration.
Personal Safety
The projector connection must be handled with great care as the
output power voltage is hazardous to human safety.
Do not pull out the cable with power on.
Equipment Safety
To disconnect the
projector/receiver/SVP
cable from the RSP, hold
on the groove part of the
connector (at the arrows)
and pull gently outwards.
Do not pull directly on
the cords, as this will
damage both cables and
the RSP.
Do not bend the cables beyond the
recommended limits when positioning the cables.
Flexing the cable to less than the specified bend
radius will damage the cable.
Female wet-end
connectors must
be lubricated at
regular intervals
even if not
mated/unmated, or
every 5 matings to
avoid damaged
male connectors (as shown here).
Use Molykote® 44 Medium as included in
your delivery.
Use and Disclosure of Data
EU Uncontrolled Technology:
Information contained herein is uncontrolled under the E.U. Regulation (EC) No 428/2009.
However, export, reexport or diversion contrary to law is prohibited.

SeaBat T-Series Rackmount
SeaBat T20-R / T50-R - Quick Reference Guide
Teledyne RESON reserves the right to change the content of this document without notice. Teledyne RESON makes no warranty of any kind with regard to this material, and shall not be liable for errors
contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Copyright © 2016-2020 Teledyne RESON A/S. All rights reserved.
Teledyne RESON A/S
Fabriksvangen 13, 3550 Slangerup, Denmark
www.teledynemarine.com/reson
Helpdesk: [e-mail]
[e-mail]
Hotline: Europe: [phone] / USA: [phone]
PDS: [phone]
RSP – Rear Panel Connections
1) Mains power input 100-230VAC
8) Alternate SVP serial port w/LED (COM 3)
2) Protective earth screw for equipotential connection
9) Main SVP serial port with power
3) 1PPS out
10) Ethernet for laptop/PC
Ethernet for NAS
4) Trigger in
a1) Time in serial port UTC/ZDA w/LED
5) Trigger out
a2) Motion in serial port w/LED
6) Projector connection(s)
a3) COM 4 serial port w/LED (RS-232) (ship’s heading)
7) Receiver connection(s)
a4) 1PPS in
RSP INS Configuration – Rear Panel Connections
1) Mains power input 100-230VAC
9) Main SVP serial port with power
2) Protective earth screw for equipotential connection
10) Ethernet for laptop/PC
Ethernet for NAS
3) 1PPS out
b1) Antennas 1 and 2
4) Trigger in
b2) IMU
5) Trigger out
b3) Time out serial port UTC/ZDA w/LED
6) Projector connection(s)
b4) Motion out serial port w/LED
7) Receiver connection(s)
b5) COM 3-5 configurable serial ports w/LED
8) Alternate SVP serial port w/LED (COM 3)
b6) GNSS serial port

SeaBat T-Series Rackmount
SeaBat T20-R / T50-R - Quick Reference Guide
Teledyne RESON reserves the right to change the content of this document without notice. Teledyne RESON makes no warranty of any kind with regard to this material, and shall not be liable for errors
contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Copyright © 2016-2020 Teledyne RESON A/S. All rights reserved.
Teledyne RESON A/S
Fabriksvangen 13, 3550 Slangerup, Denmark
www.teledynemarine.com/reson
Helpdesk: [e-mail]
[e-mail]
Hotline: Europe: [phone] / USA: [phone]
PDS: [phone]
Operator Laptop/PC – Minimum Requirements
These are the minimum requirements for the customer-furnished laptop/PC, which should be sufficient
to run both Sonar User Interface and Teledyne PDS*:
CPU: high-end quad core processor
Gb Ethernet
Graphic card: with OPENGL support and 1GB memory, e. g. NVidia GeForce GTX 4xx
8GB RAM memory
Hard disk: 1 x 500GB
Windows 10 (64 bit mandatory)
Serial Data Input
The RSP uses DB9 connectors as inputs for
COM 1 to COM 4 (or for the INS configuration,
COM 1 to COM 5 and the GNSS port).
Handshake and control wires have been
looped to ensure that devices with flow
control/handshake can send data to the
rack-mounted sonar processor.
The pin assignments of the DB9 connector:
Ground
TxData (down)
RxData (up)
RS-232 signals DB9
5
3
2
Connect the SVP to either “COM 3” (item 8)
OR “SVP” (item 9) which also provides power
for the SVP. The pinout of the Fischer
connector at the processor is as shown. For
wiring to the SVP, see the appropriate product
manual.
8PWR GND
1RS232 GND
7
6
5
PWR +12V 9
RS232 RX 2
10
RS232 TX 3
X
X4
X
X
X
Fischer connector reference: S105A062-130
Setup of SeaBat T-Series Rackmount System*
Connect the SeaBat T20-R/T50-R to the network.
oFactory default is 10.11.10.1 for LAN 1 and 10.11.10.2 for LAN 2 (limited configurable between
10.11.10.2 and 10.11.10.92).
oFactory default is 10.11.10.11 for the optional INS.
The connection from the operator laptop/PC to the RSP is done via the SUI.
oGo to the Hardware pane, and click the Sonar address drop-down menu. The T20-R/T50-R system can
be identified by its serial no. next to the IP address. Find the serial no. on the front of the RSP.
* For further details, please refer to the appropriate manual.
2Fixed IP only, full range with DHCP assigned IP.