Teledyne LabMaster 10 Zi Series User manual

Operator’s Manual
LabMaster 10 Zi Series
Oscilloscopes

LabMaster 10Zi Series Oscilloscopes
Operator's Manual
PRELIMINARY VERSION

700 Chestnut Ridge Road
Chestnut Ridge, NY, 10977-6499
Tel: [phone]
Fax: [phone]
teledynelecroy.com
© 2012 Teledyne LeCroy. All rights reserved.
Unauthorized duplication of Teledyne LeCroy documentation materials other than for internal sales
and distribution purposes is strictly prohibited. However, clients are encouraged to distribute and
duplicate Teledyne LeCroy documentation for their own internal educational purposes.
Teledyne LeCroy and other product or brand names are trademarks or requested trademarks of
their respective holders. Information in this publication supersedes all earlier versions.
Specifications are subject to change without notice.
LM10Zi-GSM-E PRELIMINARY
921419-00 PRELIMINARY

Getting Started Guide
LM10Zi-GSM-E Rev A
i
Contents
Welcome ......................................................................................................... 1
Safety Requirements........................................................................................ 2
LabMaster 10 Zi Hardware Overview .............................................................. 9
Front of MCM-Zi Master Control Module...................................................... 12
Back of MCM-Zi Master Control Module ....................................................... 13
Front of 10-xxZi Acquisition Module.............................................................. 15
Back of 10-xxZi Acquisition Module............................................................... 16
Front of ChannelSync Mainframe Hub........................................................... 17
Back of ChannelSync Mainframe Hub............................................................ 17
The I/O Panel ................................................................................................. 18
Front Panel Controls ...................................................................................... 19
Touch-Screen Displays ................................................................................... 20
LabMaster Setup ........................................................................................... 21
Connecting LabMaster Components ............................................................. 21
PCIe 1 Lane Cable SYNC Connection(s) .......................................................... 21
PCIe 4 Lane DATALINK Connection(s) ............................................................ 24
SMA 72" Cables - ChannelSync Clock............................................................. 27
ChannelSync Mainframe Hub ........................................................................ 30
Power Cable and Main Power Switch ............................................................ 31
External Display Setup ................................................................................... 32
Removing and Attaching the Front Panel ...................................................... 33
LabMaster Calibration.................................................................................... 35
Probe and Signal Connection Interfaces ........................................................ 41
Probe Interfaces............................................................................................. 41
Probes ............................................................................................................ 42
Connecting to 1.85 mm Probe Interfaces ...................................................... 42
Connecting to 2.92 mm Probe Interfaces ...................................................... 43
Probe Dialog................................................................................................... 44
Basic Controls................................................................................................ 46
Front Panel Control Groupings ...................................................................... 46

LabMaster 10 Zi Oscilloscopes
ii
LM10Zi-GSM-E Rev A
Display Dashboard ......................................................................................... 52
Turning on Channels and Traces .................................................................... 69
Timebase....................................................................................................... 70
Timebase Dialog............................................................................................. 70
Combining Channels ...................................................................................... 70
Timebase Setup and Control.......................................................................... 73
Sampling Modes............................................................................................ 74
Sampling Modes Overview ............................................................................ 74
Selecting a Sampling Mode............................................................................ 74
Single-shot Sampling Mode ........................................................................... 75
Sequence Sampling Mode –Working with Segments ................................... 76
RIS Sampling Mode - For Higher Sampling Rates........................................... 84
Vertical.......................................................................................................... 85
Vertical Overview........................................................................................... 85
Channel Dialog ............................................................................................... 85
Pre-Processing Controls ................................................................................. 87
Response Optimization Modes ...................................................................... 89
LabMaster Channel Setup.............................................................................. 91
LabMaster Calibration.................................................................................... 92
Trigger........................................................................................................... 98
Trigger Overview............................................................................................ 98
Trigger Types.................................................................................................. 99
Trigger Settings ............................................................................................ 103
Trigger Setup................................................................................................ 104
TriggerScan .................................................................................................. 110
Viewing Waveforms .................................................................................... 114
Display.......................................................................................................... 114
Persistence................................................................................................... 118
WaveStream Display Mode.......................................................................... 120
Zooming Waveforms ................................................................................... 122
Zooming Waveforms Overview ................................................................... 122
Zooming a Single Channel............................................................................ 123

Getting Started Guide
LM10Zi-GSM-E Rev A
iii
Touch-and-Drag Zooming ............................................................................ 125
Quickly Zooming Waveforms and Multiple Waveforms .............................. 126
Cursors ........................................................................................................ 127
Cursors Overview......................................................................................... 127
Cursors Setup............................................................................................... 127
Measurements ............................................................................................ 131
Measurement Parameters Overview........................................................... 131
Parameter Setup .......................................................................................... 132
Measure Modes ........................................................................................... 134
Help Markers................................................................................................ 135
Math ........................................................................................................... 138
Math Setup .................................................................................................. 138
Math and Measurement Analysis................................................................ 141
Track vs. Trend ............................................................................................. 142
Viewing Histograms ..................................................................................... 143
Viewing Trends ............................................................................................ 147
Viewing a Track ............................................................................................ 148
Pass/Fail Parameter Testing......................................................................... 149
Mask Testing ................................................................................................ 158
WaveScan Overview .................................................................................... 162
Customization Overview .............................................................................. 164
Documenting Work with LabNotebook ....................................................... 166
LabNotebook Overview ............................................................................... 166
Using LabNotebook...................................................................................... 167
Save/Recall.................................................................................................. 173
Save/Recall Overview .................................................................................. 173
Saving and Recalling Setups......................................................................... 173
Saving and Recalling Waveforms ................................................................. 175
Utilities........................................................................................................ 181
Utilities Setup............................................................................................... 181
Disk Utilities ................................................................................................. 195
Preferences Setup........................................................................................ 196

LabMaster 10 Zi Oscilloscopes
iv
LM10Zi-GSM-E Rev A
System Recovery ......................................................................................... 203
Reference .................................................................................................... 204
Warranty ...................................................................................................... 204
Specifications ............................................................................................... 205
Certifications................................................................................................ 205
Contact Teledyne LeCroy ............................................................................. 210
End-User License Agreement for Teledyne LeCroy®X-Stream Software ..... 211
Windows®License Agreement ..................................................................... 222
Index ........................................................................................................... 223

Getting Started Guide
LM10Zi-GSM-E Rev A
1
Welcome
Thank you for purchasing a Teledyne LeCroy product. We're certain
you'll be pleased with the detailed features so unique to our
instruments.
About this Manual
This manual contains information needed to set up and operate the
oscilloscope including Hardware Overview and Set Up, Probe and Signal
Connection Interfaces, Basic Controls, Core Oscilloscope Functions, and
Reference (certifications and contact information).
The Teledyne LeCroy website at teledynelecroy.com always maintains
the most current specification information. The website should be
checked for frequent updates.
Support
When your product is delivered, verify that all items on the packing list
or invoice copy have been shipped to you. Contact your nearest
Teledyne LeCroy customer service center at the address listed in this
manual or your national distributor if anything is missing or damaged. If
you do not contact us immediately, we cannot be responsible for
replacement.
Thank You
We truly hope these materials increase your enjoyment and
understanding of your Teledyne LeCroy product.
Sincerely,
David C. Graef
Vice President and Chief Technology Officer
Teledyne LeCroy

LabMaster 10 Zi Oscilloscopes
2
LM10Zi-GSM-E Rev A
Safety Requirements
This section contains information and warnings that must be observed
to keep the instrument operating in a correct and safe condition. You
are required to follow generally accepted safety procedures in addition
to the safety precautions specified in this section.
The overall safety of any system incorporating this instrument is the
responsibility of the assembler of the system.
Safety Symbols
These symbols on the instrument's front or rear panels, or in this
manual, alert you to important safety considerations.
This symbol is used where caution is required. Refer to the
accompanying information or documents in order to protect against
personal injury or damage to the instrument.
This symbol warns of a potential risk of electric shock.
This symbol is used to denote the measurement ground
connection.
This symbol is used to denote a safety ground connection.
This symbol indicates the power switch located on the front of
the oscilloscope. Pressing this button toggles the oscilloscope's state
between operating and Standby mode. This switch is not a disconnect
device. The instrument can only be placed in a complete Power Off
state by disconnecting the power cord.
This symbol is used to denote Alternating Current.

Getting Started Guide
LM10Zi-GSM-E Rev A
3
The word CAUTION indicates a potential hazard. It calls attention to a
procedure, practice or condition which, if not followed, could possibly
cause damage to equipment. If a CAUTION is indicated, do not proceed
until its conditions are fully understood and met.
The word WARNING indicates a potential hazard. It calls attention to a
procedure, practice or condition which, if not followed, could possibly
cause bodily injury or death. If a WARNING is indicated, do not proceed
until its conditions are fully understood and met.
CAT denotes the Installation (Overvoltage) Category rating per EN
61010-1:2010 safety standard. CAT I rated terminals (e.g., measurement
inputs on front of the oscilloscope) must only be connected to source
circuits where measures are taken to limit transient voltages to an
appropriately low level.
Operating Environment
The instrument is intended for indoor use and should be operated in a
clean, dry environment. Before using this product, ensure that its
operating environment is maintained within these parameters:
Temperature: 5 to 40 °C.
Humidity: Maximum relative humidity 80 % for temperatures up to
31° C decreasing linearly to 50 % relative humidity at 40° C (or at the
upper operational temperature limit).
Altitude: Up to 10,000 ft (3,048 m) at or below 25° C.
NOTE: Direct sunlight, radiators, and other heat sources should be taken
into account when assessing the ambient temperature.
WARNING The oscilloscope must not be operated in explosive,
dusty, or wet atmospheres.
CAUTION Protect the oscilloscope's display touch screen from
excessive impacts with foreign objects.

LabMaster 10 Zi Oscilloscopes
4
LM10Zi-GSM-E Rev A
CAUTION Do not exceed the maximum specified front panel
terminal voltage ratings. Refer to Specifications for more details. The
specifications for maximum allowable voltages are located on a label on
the front of the oscilloscope.
Safety Certification
The design of the instrument has been verified to conform to safety
standards EN 61010-1:2010, EN 61010-2-030:2010, UL 61010-1 Third
Edition, and CAN/CSA C22·2 No·61010-1-12. See Certifications on page
205 for details.
Cooling
The instrument relies on forced air cooling with internal fans and
ventilation openings. Care must be taken to avoid restricting the airflow
around the apertures (fan holes) on any side of the oscilloscope. For
sides and rear apertures, ensure adequate ventilation by leaving the
required 15 cm (6 inches) minimum gap around the sides and rear of
the instrument. For bottom apertures, the oscilloscope feet (up or
down) provide adequate clearance. Ensure at least the minimum feet
clearance is achieved as paper or light objects can be drawn to and
obstruct the opening(s).
CAUTION Do not block oscilloscope ventilation holes. Always
keep items like sheets of paper clear of the oscilloscope bottom.
The instrument also has internal fan control circuitry that regulates the
fan speed based on the ambient temperature. This is performed
automatically after start-up with no manual intervention required.
CAUTION Do not allow any foreign matter to enter the
oscilloscope through the ventilation holes, etc.

Getting Started Guide
LM10Zi-GSM-E Rev A
5
AC Power Source
100 to 240 VAC (±10%) at 50/60 Hz (± 10%).
Manual voltage selection is not required because the instrument
automatically adapts to line voltage.
Power Consumption
MCM-Zi Master Control Module
≤450 watts (450 VA) (depending on accessories installed –PC
port plug-ins etc.).
Acquisition Modules
25-36 GHz Models - ≤1100 watts (1100 VA) for 25-36 GHz
LabMaster 10 Zi series models (depending on accessories
installed - probes, serial trigger option, etc.).
50-65 GHz Models - ≤1150 watts (1150 VA) for 30-45 GHz
LabMaster 10 Zi series DBI models (depending on accessories
installed - probes, serial trigger option, etc.).
Power and Ground Connections
The MCM-Zi Master Control Module is provided with a 10A/250V rated
grounded cord set containing a molded three-terminal polarized plug
with a standard IEC-60320 (Type C13) connector. The connector mates
to a compatible power inlet on the Master Control Module for making
line voltage and safety ground connections.
The 10-xxZi Acquisition Module is provided with a 16A/250V or
15A/125V rated grounded cord set containing a molded three-terminal
polarized plug and a specific IEC-60320 (Type C19) connector. The
connector mates to a compatible power inlet on the Acquisition Module
for making line voltage and safety ground connections.
For both modules, power inlet ground terminal is connected directly to
the frame of the respective instrument. For adequate protection

LabMaster 10 Zi Oscilloscopes
6
LM10Zi-GSM-E Rev A
against electrical shock hazard, the power cord plug must be inserted
into a mating AC outlet containing a safety ground contact.
WARNING Only use the power cord provided with your
instrument. Any interruption of the protective conductor inside or
outside of the oscilloscope, or disconnection of the safety ground
terminal creates a hazardous situation. Intentional interruption is
prohibited.
In Standby mode, the oscilloscope is still connected to the AC supply.
The instrument can only be placed in a complete Power Off state by
removing the power cord.
CAUTION Do not place the instrument so that it is difficult to
reach the power cord inlet to disconnect the instrument.
CAUTION Always use the Power Switch or File →Shutdown
command in the software to properly shut down your instrument.
Never substitute this practice by pulling the instrument power cord
from the socket or shutting down a connected power strip.
Standby (Power) Switch and Oscilloscope
Operational States
For the MCM-Zi Master Control Module, the Standby (Power) switch
controls the operational state of the oscilloscope. This toggle switch is
activated by momentarily pressing and releasing it.
The oscilloscope's factory settings result in only two basic oscilloscope
states: On or Standby. In the case of Standby, the oscilloscope is
powered off with the exception of some housekeeping circuitry. The
oscilloscope can only be placed in a complete power off state by
unplugging the power cord from the primary power source (AC outlet).
It is recommended that the power cord be unplugged from the AC
outlet if the oscilloscope is not being used for an extended period of
time.

Getting Started Guide
LM10Zi-GSM-E Rev A
7
CAUTION Hibernate mode is not supported by the Power button.
Therefore, Windows® Power Options must not be changed from the
default Never setting to System Standby or System Hibernate modes.
CAUTION Always use the Power Switch or File →Shutdown
command in the software to properly shut down your instrument.
Never substitute this practice by pulling the instrument power cord
from the socket or shutting down a connected power strip.
Oscilloscope Calibration
The recommended calibration interval is one year. Calibration should be
performed by qualified personnel only.
Cleaning
Clean only the exterior of the instrument, using a damp, soft cloth. Do
not use harsh chemicals or abrasive elements. Under no circumstances
allow moisture to penetrate the instrument.
Avoid electrical shock hazard by unplugging the power cord from the AC
outlet before cleaning.
WARNING There are no operator serviceable parts inside. Do not
remove covers. Refer servicing to qualified personnel.
Lifting and Moving
Components housed in the OC910 oscilloscope cart may be wheeled
from place to place as a unit. If components must be removed from the
cart or other mounting, disconnect and move components separately.
We recommend using two persons, one at each end, to lift and stack
components.

LabMaster 10 Zi Oscilloscopes
8
LM10Zi-GSM-E Rev A
Abnormal Conditions
Operate the instrument only as intended by the manufacturer. Carefully
read all instructions and labels.
WARNING Using the oscilloscope in a manner not specified by
the manufacturer may impair the instrument's safety protection.
The oscilloscope's protection is likely to be impaired if, for example, the
instrument shows visible damage or has been subjected to severe
transport stresses.
Other indications of impairment due to hazardous electrical quantities
might include obviously incorrect measurement behaviors.
If you suspect the oscilloscope's protection has been impaired,
disconnect the power cord and secure the instrument against any
unintended operation. Contact Teledyne LeCroy immediately regarding
repair.

Getting Started Guide
LM10Zi-GSM-E Rev A
9
LabMaster 10 Zi Hardware
Overview
LabMaster 10 Zi is a unique modular oscilloscope solution that allows a
configuration of more channels at higher bandwidths than conventional
four channel oscilloscopes. It is ideally suited for test situations where
there are many lanes of serial data to be captured and analyzed
simultaneously, crosstalk analysis or for capturing four or more channels
at the highest-possible bandwidths for optical coherent modulation
applications. Each LabMaster consists of a single Master Control
Module, additional Acquisition Modules, and a ChannelSync Mainframe
Hub in systems where more than five acquisition modules are required.
Acquisition Modules can be added at any time for easy channel
upgrades. Bandwidth upgrades are available for future scalability.
Unique ChannelSync™ architecture ensures precise synchronization
between all oscilloscope channels located in different acquisition
modules. A single 10 GHz distributed clock signal is generated in the
MCM-Zi Master Control Module, and then used in or distributed to as
many as twenty 10-xxZi Acquisition Modules. The 10 GHz clock
frequency - 1000 times faster than the 10 MHz reference clocks
commonly used to synchronize lab equipment - ensures precise
synchronization and high-timebase accuracy between all acquisition
modules. The system ensures Acquisition Modules are automatically
identified to the Master, and software calibration routines allow for fast
calibration and correction for any static acquisition skew between all
acquisition modules.
Detailed steps explaining how to configure hardware are covered in
Connecting LabMaster Components on page 21.

LabMaster 10 Zi Oscilloscopes
10
LM10Zi-GSM-E Rev A
MCM-ZiMaster Control Module with up to five10-xxZi Acquisition Modules

Getting Started Guide
LM10Zi-GSM-E Rev A
11
The 10-xxZi Acquisition Modules are available in a variety of bandwidths
and channel density configurations. The example above contains a mix
of 36 GHz and 65 GHz models. Refer to specifications on the product
datasheet maintained at www.teledynelecroy.com for more
information.
NOTE: If your LabMaster system runs multiple Acquisition Modules, for
optimal channel access and convenience, Teledyne LeCroy recommends
stacking the modules on top of each other on your bench, inside
Teledyne LeCroy's available OC910, or inside of your own rack (modules
must be specifically ordered for rack mounting from the Teledyne
LeCroy factory).

LabMaster 10 Zi Oscilloscopes
12
LM10Zi-GSM-E Rev A
Front of MCM-Zi Master Control Module
The MCM-Zi Master Control Module includes Controls, Display, CPU,
and ChannelSync Clock Architecture. All acquisition capability is
contained in separate Acquisition Modules.
Number and Description
1. Power
Button
2. Fast Edge
Output
3. Host USB Ports
4. Detachable Front Panel
Control
5. Front Panel Control
Release Switch

Getting Started Guide
LM10Zi-GSM-E Rev A
13
Back of MCM-Zi Master Control Module
Number and Description
1. ChannelSync Outputs -
SMA 10 GHz Clock and
PCIe 1 Lane Control
Connections (for
corresponding
Acquisition Modules)
2. 10 MHz Reference
Clock Output
3. 10 MHz Reference
Clock Input
(Grounded EMI
Shield required when
port is not in use)
4. Removable Storage
Drive
5. AC Power Inlet
6. The I/O Panel
7. DVI-D Video
Output
8. PCIe 4 Lane Data
Inputs (from
corresponding
Acquisition
Modules.
PLEASE NOTE THE FOLLOWING:
Cap-off unused ChannelSync SMA sockets (item number 1 on the
back of your Master Control Module) using the provided chain-
linked 50 Ωterminations (not shown).
10 MHz Reference Clock Inputs are specifically intended for
synchronization with other instruments; not between Master
Control Module and Acquisition Modules.
DVI-D Video Output is for use with an additional external
monitor for Extended Desktop mode.