Teledyne T3HVD User manual

T3HVD Voltage Probe Manual
High Voltage Dierential Probes

Contents
Safety Terms and Symbols .................................................................................. 1
Voltage vs. Frequency Derating and Burn Limit .................................................. 3
Voltage Derating for combined Probe and Accessories ....................................... 5
Product Overview ................................................................................................ 6
Key Features ...................................................................................................6
Applications ......................................................................................................6
Product Description .............................................................................................. 7
Operating Instructions .......................................................................................... 7
Adjusting The Probe Offset ................................................................................... 8
Supplied Accessories ........................................................................................... 9
Specications ..................................................................................................... 10
Performance Verication ..................................................................................... 11
DC Accuracy Test ........................................................................................... 11
Rise Time Test ............................................................................................... 12
DC Common Mode Ratio Test ....................................................................... 12
Test Record Form .......................................................................................... 13
Care and Maintenance ....................................................................................... 13
Reference ........................................................................................................... 13
Certications ....................................................................................................... 14
Safety Compliance ............................................................................................. 15
Environmental Compliance ................................................................................ 15
Warranty ............................................................................................................ 17
© 2021 Teledyne LeCroy, Inc. All rights reserved.
Teledyne Test Tools is a trademark of Teledyne LeCroy, Inc. Other product or brand names are
trademarks or requested trademarks of their respective holders. Information in this publication
supersedes all earlier versions. Specications are subject to change without notice.

Page 1
Safety
To maintain the probe in a correct and safe condition, observe generally accepted safety
procedures in addition to the precautions specified in this section. The overall safety of any
system incorporating this product is the responsibility of the assembler of the system.
Symbols
These symbols appear on the probe and accessories or in this manual to alert you to important
safety considerations.
WARNING, HIGH VOLTAGE.Risk of electric shock or burn.
CAUTION of damage to probe or instrument, or WARNING of hazard to health.
Attend to the accompanying information to protect against personal injury or damage.
Do not proceed until conditions are fully understood and met.
ESD CAUTION.Risk of Electrostatic Discharge (ESD) that can damage the probe or
instrument if anti-static measures are not taken.
Precautions
WARNING.To avoid personal injury or damage due to electric shock or fire:
Do not overload; observe all terminal ratings.Do not apply any potential that exceeds the
maximum rating of the probe and/or the probe accessory, whichever is less.
Comply with the Voltage vs. Frequency Derating curve when measuring higher frequency
signals.
Connect and disconnect properly. Always connect the probe input lead to the probe
accessories before connecting to a voltage source. Ensure the connections are secure before
applying voltage. Do not disconnect leads or accessories from a live circuit.
Keep the probe body and output cable away from the circuits being measured. Only
accessory tips are intended for contact with electrical sources.
Use only accessories compatible with the probe.Use only accessories that are rated for the
application. Substituting other accessories than those specified in this manual may create a
shock /burn hazard.
Keep fingers behind the nger guard of the probe accessories.

Page 2
Do not remove the probe's casing. Touching exposed connections may result in electric
shock or burn.
CAUTION.To prevent damage to the equipment:
Use only as specified. Use of the probe and/or the equipment it is connected to in a manner
other than specified may impair the protection mechanisms.
Do not bend cables excessively.
Use only within the operational environment listed.Do not use in wet or explosive
atmospheres.
Keep product surfaces clean and dry.
Do not operate with suspected failures.Before each use, inspect the probe and accessories
for any damage such as tears or other defects in the probe body, cable jacket, accessories,
etc. If any part is damaged, cease operation immediately and sequester the probe from
inadvertent use.
Operating Environment
Temperature, Operating
0 C to 50 C
Temperature, Non-operating -30 C to 70 C
Relative Humidity, Operating
≤85% Relative Humidity
Relative Humidity, Storage
≤90% Relative Humidity
Altitude, Operating 3000 m
Altitude, Storage 12000 m
Usage Indoors

Page 3
Voltage vs. Frequency Derating and Burn Limit
T3HVD1500-70 and T3HVD1500-200 Derating and Burn Limit
The maximum input voltage curve (solid line) shows the maximum voltage that can be
applied to the probe inputs without risking damage to the probe.
The lower Burn Limit curve (dashed line) shows the maximum voltage that can be applied to
the probe inputs while the operator is handling the inputs. Handling the inputs while
connected to active signals above this burn limit could result in injury to the operator.
WARNING. To avoid risk of electric shock or re, comply with the burn limit when
measuring high-frequency signals with hand-held accessories. Do not exceed the
voltage or category rating of the probe or accessories (whichever is less). Keep
your ngers behind the nger gaurd of the probe. Keep the probe body and output
cable away from the circuts being measured. Use only the specied accessories.
0
200
400
600
800
1000
1200
1 kHz 10 kHz 100 kHz 1 MHz 10 MHz 100 MHz
Voltage (Vrms)
Frequency Vmax Burn Limit

Page 4
T3HVD7000-100 Derating and Burn Limit
0
500
1000
1500
2000
2500
1 kHz 10 kHz 100 kHz 1 MHz 10 MHz 100 MHz
Voltage (Vrms)
Frequecny Vmax
Burn Limit

Page 5
* See "IEC/EN 61010-031 Denitions" on p.13.
**
Alligator Clip type depends on probe model, see accessory diagrams on page 9.
CAUTION. The operating altitude of the probe is derated to 2000 m (6560 ft) when
used with the above accessories.
WARNING. Each accessory has a dierent measurement (overvoltage)
category(CAT) rating. The voltage and CAT rating of the probe are derated to the
values in the table above when used with the corresponding accessory.
WARNING. While all probes may be used with the T3HVD accessories (alligator
clips, pincer clips, etc.), the voltage and CAT ratings of the probe are derated to the
values in the table above when used with the corresponding accessory.
WARNING. To avoid risk of electric shock or re, do not exceed either the voltage
rating or category rating. Keep your ngers behind the nger guard of the probe.
Keep the probe body and output cable away from the circuits being measured. Use
only the specied accessories.
Voltage Derating for combined Probe and Accessories
Derated Max. Input Voltage for combined Probe & Accessory (either input to ground)*
Accessory T3HVD1500-70 T3HVD1500-200 T3HVD7000-100
Alligator Clips** CAT II 1000V / CAT III 600V CAT III 1000V
CAT IV 600V
Pincer Clips CAT III 1000V
Hook Clips CAT III 1000V
Extender Leads CAT III 1000V

Page 6
PRODUCT OVERVIEW
T3HVD1500-70: 1500 V peak, 70 MHz
T3HVD1500-200: 1500 V peak, 200 MHz
T3HVD7000-100: 7000 V peak, 100 MHz
Key Features
●Accurate and easy voltage measurements.
●Wide 200 MHz bandwidth.
●Differential signal input of up to +7000V (DC + Peak
AC) depending on model.
●High differential input impedance of up to 40 MΩ /
<2.5pF depending on model.
●Maximum common mode voltage of +7000V.
●Combined single ended and differential
measurement capability.
●Use with any scope with a 1MΩ input and BNC
connector.
●Over-Voltage alarm with dual indicators.
●Switchable bandwidth limit to reduce noise.
Teledyne Test Tools new T3HVD range of high voltage dierential probes are wide bandwidth active
dierential voltage probes, featuring models with bandwidths up to 200 MHz bandwidth, voltages up
to +7000V (DC + Pk AC), fast and accurate waveform capture, measurement accuracy of +2% and
low test circuit loading.
These probes can be used with any oscilloscope having a 1MΩ BNC input.
Applications
●Power electronics.
●Multi-phase motor drives (electric vehicles, etc).
●Inverters and power conversion.
●Domestic and industrial photo-voltaic (PV) system
design.
●General vehicle electronics.
●Power supply design.
●Floating voltage measurements.
●Domestic appliances (washing machines, induction
hobs, etc).
●Research and development.
●Universities, general electronics and education.

Page 7
T3HVD Product Description
Measurement voltage input leads
Maximum measurable differential voltage
Maximum input voltage to earth
Overload indicator
Attenuation / range Indicator
Bandwidth indicator
Audible range overload indicator
Attenuation / range switch
Audible range overload
on / o switch
Output BNC
Bandwidth limit switch
Operating Instructions
●DUT measurement input leads: The integral input test leads extend 26cm from the probe body. Connect
the integral test leads directly to your DUT or use the extender leads and other accessories if necessary.
For best measurement signal integrity it is better not to extend the integral input test leads if possible. If
the extender leads are used then it is recommended to use the bandwidth limit.
●If possible it is good practice to wind the DUT measurement input leads together to improve noise
immunity and give the best frequency response. If the extender leads are used then these should also be
twisted together if possible.

Page 8
●The Attenuation / Range Switch is used to select between the two voltage ranges supported by the probe,
see the table below. The oscilloscope vertical range scale can be set to the range ratio below for correct
oscilloscope vertical scaling. Note that the probe can be damaged if too high a voltage is applied to it,
therefore always check the voltage range before connecting to a DUT.
●The bandwidth selection button allows selection between the probes’ default setting of Full bandwidth or 5
MHz. An alternative is to use a bandwidth limit setting within the measurement oscilloscope. Most
oscilloscopes have a bandwidth limit capability. Limiting the bandwidth will reduce the noise in
environments where the full bandwidth of the probe is not needed.
●The audible range overload switch will turn on or o a buzzer that indicates when the probe is being used
beyond its maximum voltage. Immediately reduce the measurement voltage to avoid damage to the
probe, or switch to the higher voltage range if the probe is being used on its lower voltage range.
●The probe output BNC connector can be connected to any oscilloscope with a BNC and 1MΩ input
impedance using the supplied BNC to BNC cable. If the oscilloscope input impedance is set to 50Ω then
the measured oscilloscope voltage will be incorrect.
●Power for the T3HVD probes can be supplied from the included USB power supply or from a USB socket
built into the oscilloscope. The probe has a standard USB type B interface.
●The probe default settings are: High voltage range, full bandwidth and audible over voltage alarm on. The
probe will automatically save its state before power off.
●To setup the probe to make a measurement rst connect it to the oscilloscope using the BNC to BNC
cable. Attach the power to the probe. Select the correct voltage measurement range (low / high)
depending on the DUT. Set the oscilloscope vertical scale attenuation ratio according to the probe voltage
range selected, and set the oscilloscope measurement range. Connect the probe measurement cables to
the DUT using the supplied accessories.
●After measuring remove the probe from the DUT and power o the probe by removing the USB power
supply.
Adjusting the probe oset
If the output offset drifts from zero then it can be adjusted using the following method.
●Allow the probe 30 minutes to warm up. Connect the measurement probe tips together and check to see
if the oscilloscope is showing the probe output on the zero volts line. Note when making the probe offset
measurement that the oscilloscope should also be allowed time to warm up and that there should be NO
vertical offset set on the oscilloscope.
●Momentarily power off the T3HVD probe. Hold down the ATTENUATION and BANDWIDTH buttons on
the probe, and power the probe on.
T3HVD1500-70
50 x +150 V
500 x +1500 V
T3HVD1500-200
50 x +150 V
500 x +1500 V
T3HVD7000-100
100 x +700 V
1000 x +7000 V

Page 9
●The probe will be in test mode when the power is reapplied. This is indicated by the overload indicator light
being lit. Release the ATTENUATION and BANDWIDTH keys.
●The probe is now ready to have the high voltage range offset adjusted. Press the ATTENUATION key to
increase the voltage offset value, and press the BANDWIDTH key to decrease the voltage offset value.
Adjust the keys until the offset is at zero.
●Now switch the probe to the low voltage range by pressing the AUDIBLE OVERRANGE button. Press the
ATTENUATION key to increase the voltage offset value, and press the BANDWIDTH key to decrease the
voltage offset value. Adjust the keys until the offset is at zero.
●Pressing the AUDIBLE OVERRANGE button again will exit the voltage offset adjustment mode and return
the probe to normal operating mode.
Supplied Accessories
●The T3HVD probe kit also includes a USB power supply (not pictured) that the T3HVD USB A to B Power
Cable can connect to.
●The T3HVD Extender Leads and the T3HVD BNC to BNC Cable are 1m long each
●The T3HVD USB A to B Power Cable is 1.5m long
T3HVD1500-70 and T3HVD1500-200
Alligator Clips x 2
T3HVD7000-100 Alligator Clips x 2
T3HVD Pincer Clips x 2
1m T3HVD Extender Leads x 2
1m T3HVD BNC to BNC Cable x 1
T3HVD Hook Clips x 2
1.5m T3HVD USB A to B Power Cable x 1

Page 10
Alligator Clips(1) x 2 CAT III 1000V / CAT IV 600V
Pincer Clips x 2 CAT III 1000V
Hook Clips x 2 CAT III 1000V
Extender Leads x 2 1 m, CAT III 1000V
BNC to BNC Cable x 1 1 m
USB Power Cable x 1 1.5 m
Power Adapter x 1 USB 5V / 1A
Probe Dimensions 195mm x 65mm x 28mm
Probe Weight 216g
Input Lead Length 28cm 17cm 28cm
1) Alligator Clip type depends on probe model, see accessory diagrams on page 6.
Specications
Bandwidth (-3dB) T3HVD1500-70 70 MHz 100 MHz
T3HVD1500-200 200 MHz
Rise Time T3HVD1500-70 <5 ns <3.5 ns
T3HVD1500-200 <1.75 ns
Accuracy +2 % +2 %
Attenuation / Range Selection
*CAT I per IEC/EN 61010-031/A1:2008. No Rated Measurements Category per IEC/EN 61010-031:2015 + AMD1:2018.
50 x / 500 x 100 x / 1000 x
Maximum Differential Voltage
(DC + Peak AC)
50 x +150 V 100 x +700 V
500 x +1500 V 1000 x +7000 V
Common Mode Voltage (DC +
Peak AC) +1500 V +7000 V
Maximum Input Voltage To Earth
(V rms) CAT II 1000 V / CAT III 600 V CAT I* 2300 V / CAT III 1000 V
Input Impedance
Single Ended To
Ground 5MΩ, < 4pF 20MΩ, 5pF
Between Inputs 10MΩ, < 2pF 40MΩ, 2.5 pF
CMRR
DC > 80dB > 80dB
100 kHz > 60dB > 60dB
1 MHz > 50dB > 50dB
Noise (V rms) 50 x < 50 mV 100 x < 200 mV
500 x < 300 mV 1000 x < 1.2 V
Differential Overvoltage Detection
Level
50 x >150 V 100 x >700 V
500 x >1500 V 1000 x >7000 V
Propergation
Delay
Probe Approximately 9 ns
1m BNC to BNC
Cable Approximately 5 ns
Bandwidth Limit Filter >-3dB at 5 MHz
Probe Termination Load >100 kΩ
Power Supply USB 5V / 1A Wall Socket Adapter
Safety Standard IEC/EN 61010-031:2015 + AMD1:2018
EMC Standard EN61326-1: 2013

Page 11
Performance Verication
The table below lists the test instruments required for the performance verication process.
Operating Temperature 0oC - 50oC
Storage Temperature -30oC - 70oC
Operating Humidity <85% Relative Humidity
Storage Humidity <90% Relative Humidity
Operating Altitude 3000 m
Storage Altitude
Pollution Degree
12000 m
2, Indoor Use Only
Oscilloscope Accuracy <1.5%, e.g. Teledyne LeCroy WaveSurfer
4000HD or HDO4000A Series Displays probe output
Signal Generator /
Calibrator
Amplitude Accuracy <0.75%, Rise Time <3ns, e.g.
Fluke / Wavetek 9100
Bandwidth, AC
Accuracy, CMRR
Digital Multimeter 6.5 digits minimum, e.g. Teledyne LeCroy
T3DMM6-5, Keithley 2000 DC Accuracy
Pincer Clips Supplied in probe accessories General Testing
BNC Adapters
BNC Male to BNC Female T Piece, BNC Male to
Dual Binding Posts, BNC Female to Dual Binding
Posts, BNC Male to 50Ω Termination
General Testing
●Connect power to the probe and allow 30 minutes warm up time.
DC Accuracy Test
●Connect the T3HVD probe BNC output to the Digital Multimeter input using the Male BNC to Binding
Posts adapter. Connect the male BNC connector to the T3HVD female BNC output. Connect the
Multimeter test leads to the binding posts.
●Connect the T3HVD input leads to the calibrator output directly or using the pincer clips.
●Set the probe sensitivity to the lower voltage range, apply the DC voltage from the calibrator according to
the table below, and record the output voltage on the DMM. Repeat for the higher voltage range.
T3HVD1500-70,
T3HVD1500-200
50 x 5 V 100 mV +2 mV
500 x 50 V 100 mV +2 mV
T3HVD7000-100
100 x 10 V 100 mV +2 mV
1000 x 100 V 100 mV +2 mV

Page 12
Rise Time Test
●Set the Calibrator output to give a fast rise time. Attach the BNC T piece to the calibrator output. Attach the
50Ω Termination to one arm of the T piece, attach the BNC Male to binding posts adapter to the other arm
of the T piece. Plug the probe measurement leads into the binding posts.
●Set the Calibrator output voltage to a suitable level to make a measurement on the probe, but not high
enough to damage the 50Ω Termination. Typically a 50Ω 1 Watt Termination should have no more than 7
Vrms applied.
●Connect the probe output to the oscilloscope and measure the rise time of each voltage range according
to the measurement table. Note: An oscilloscope of sucient bandwidth is required to make this
measurement, see recommended oscilloscope bandwidth in the table below.
●After measuring remove the probe from the DUT and power o the probe by removing the USB power
supply.
DC Common Mode Ratio Test
●Set the T3HVD probe to its lower voltage range and connect the probe inputs to the DC voltage source or
calibrator.
●Set the multimeter to DC Volts, connect the multimeter cables together, then auto-zero the multimeter.
T3HVD1500-70 50 x >350 MHz <5ns
500 x >350 MHz <5ns
T3HVD1500-200 50 x >1 GHz <1.75ns
500 x >1 GHz <1.75ns
T3HVD7000-100 100 x >500 MHz <3.5ns
1000 x >500 MHz <3.5ns
●Connect the T3HVD probe output BNC to the multimeter using the BNC male to binding posts adapter and
the multimeter cables.
●Set the DC voltage source or calibrator output to 500V DC. Enable the DC voltage source or
calibrator output. Record the probe output voltage, as measured by the multimeter, in the table
below.
●Disable the DC voltage source or calibrator output and remove the probe.
T3HVD1500-70,
T3HVD1500-200 50 x 500 V DC <1 mV
T3HVD7000-100 100 x 500 V DC <1 mV
●Note: High voltage 500 V DC is used during this test. Please pay attention to personal safety. Do
not turn on the 500 V DC output until the completion of all test connections. Turn off the 500 V DC
output before disconnecting the probe.

Page 13
Test Record Form
Care and Maintenance
●Keep the probe clean and dry.
●To clean wipe with a soft dry cloth. Do not use chemicals or liquids.
●Keep the probe in the case provided when not in use. This will help to keep the probe clean.
●Do not drop the probe since this can cause shock and damage the probe.
●Do not use force, excessively twist, excessively bend or pull on the input cables. This can cause damage
to the input cables and reduce the life of the probe.
Product Serial Number: Test Temperature:
Test Date: Test Humidity:
Test Model: Lower Limit Test result Upper Limit
DC Accuracy
T3HVD1500-70 50 x 98 mV 102 mV
500 x 98 mV 102 mV
T3HVD1500-200 50 x 98 mV 102 mV
500 x 98 mV 102 mV
T3HVD7000-100 100 x 98 mV 102 mV
1000 x 98 mV 102 mV
Rise Time
T3HVD1500-70 50 x - 5 ns
500 x - 5 ns
T3HVD1500-200 50 x - 1.75 ns
500 x - 1.75 ns
T3HVD7000-100 100 x - 3.5 ns
1000 x - 3.5 ns
DC Common
Mode Rejection
Ratio
T3HVD1500-70 50 x - 1 mV
T3HVD1500-200 50 x - 1 mV
T3HVD7000-100 100 x - 1 mV
Reference
IEC/EN 61010-031:2015 Denitions
Measurement Category III (CAT III) applies to test and measuring circuits connected to the distribution part
of the building’s low-voltage mains installation.
Measurement Category II (CAT II) applies to test and measuring circuits connected directly to utilization
points (socket outlets and similar points) of the low-voltage mains installation.
No Rated Measurement Category applies to other circuits that are not directly connected to the mains
supply.
Pollution Degree 2 refers to an operating environment where normally only dry nonconductive pollution
occurs. Conductivity caused by temporary condensation should be expected.
Note: The 2015 version of the standard eliminates the Measurement Category I (CAT I) rating for test and
measuring circuits that are not intended to be directly connected to the mains supply. However, this change
in rating designation does not reduce the measurement capability or the level of protection oered by the
new probe design when compared to the probes that were originally certied per the 2008 version of the
standard.

Page 14
Certications
Teledyne LeCroy certifies compliance to the following standards as of the date of publication. As
standards evolve,these may no longer be current. See the Declaration of Conformity shipped with
your product for current certifications.
EMC Compliance
EC Declaration of Conformity - EMC
The probe meets the intent of EC Directive 2014/30/EU for Electromagnetic Compatibility.
Compliance was demonstrated to the following specifications as listed in the Oicial Journal of the
European Communities:
EN 61326-1:2013, EMC requirements for electrical equipment for measurement, control,
and laboratory use.1, 2, 3
1. This product is intended for use in nonresidential areas only. Use in residential areas may cause EM interference.
2. Emissions exceeding the levels required by this standard may occur when product is connected to a test object.
3. To ensure compliance with the applicable EMC standards, use high quality shielded interface cables.
EUROPEAN CONTACT:*
Teledyne GmbH – LeCroy Division
Im Breitspiel 11c
D-69126 Heidelberg
Germany
Tel: [phone]
Australia & New Zealand Declaration of Conformity - EMC
The probe complies with the EMC provision of the Radio Communications Act per the following
standards, in accordance with requirements imposed by the Australian Communication and Media
Authority (ACMA):
AS/NZS CISPR 11:2009/A1:2010, EN 55011:2009/A1:2010 Radiated and Conducted Emissions,
Group 1, Class A.
AUSTRALIA / NEW ZEALAND CONTACTS:*
RS Components Pty Ltd.
Suite 326 The Parade West
Kent Town, South Australia 5067
RS Components Ltd.
Unit 30 & 31 Warehouse World
761 Great South Road
Penrose, Auckland, New Zealand
* Visit teledynelecroy.com/support/contact for the latest contact information.

Page 15
Safety Compliance
EC Declaration of Conformity – Low Voltage
The probe meets the intent of EC Directive 2014/35/EU for Product Safety.
Compliance was demonstrated to the following specications as listed in the Ocial Journal of the
European Communities:
IEC/EN 61010-031:2015 Safety requirements for electrical equipment for measurement, control, and
laboratory use – Part 31: Safety requirements for hand-held probe assemblies for electrical
measurement and test.
Environmental Compliance
End-Of-Life Handling
The probe is marked with this symbol to indicate that it complies with the applicable
European Union requirements to Directives 2012/19/EU on Waste Electrical and
Electronic Equipment (WEEE).
The probe is subject to disposal and recycling regulations that vary by country and
region. Many countries prohibit the disposal of waste electronic equipment in standard
waste receptacles. For more information about proper disposal and recycling of your
Teledyne LeCroy product, visit teledynelecroy.com/recycle.
Restriction of Hazardous Substances (RoHS)
The product and its accessories conform to the 2011/65/EU RoHS2 Directive inclusive of any further
amendments or modications of said Directive.
See package inserts for other environmental certications.

Page 16
CHINA RoHS 2
Unless otherwise specied, all the materials and processes are compliant with the latest requirements
of China RoHS 2. The hazardous substances contained in the instrument are disclosed in accordance
with the standards SJ/T 11364-2014 (Marking for the restricted use of hazardous substances in
electronic and electrical products) and GB/T 26572-2011 (Requirements on concentration limits for
certain restricted substances in electrical and electronic products). The instrument is marked with an
appropriate Environmental Friendly Use Period (EFUP) symbol. The packaging materials include the
appropriate recycling labels. The below substance disclosure tables (in Chinese and English languages)
provide the required compliance information.

Page 17
Warranty
Teledyne LeCroy warrants this oscilloscope accessory for normal use and operation within specication
for a period of one year from the date of shipment. Spare parts, replacement parts and repairs are
warranted for 90 days. In exercising its warranty, Teledyne LeCroy, at its option, will either repair or
replace any assembly returned within its warranty period to the Customer Service Department or an
authorized service center. However, this will be done only if the product is determined by Teledyne
LeCroy’s examination to be defective due to workmanship or materials, and the defect is not caused by
misuse, neglect, accident, abnormal conditions of operation, or damage resulting from attempted repair
or modications by a non-authorized service facility.
The customer will be responsible for the transportation and insurance charges for the return of products
to the service facility. Teledyne LeCroy will return all products under warranty with transportation
charges prepaid.
This warranty replaces all other warranties, expressed or implied, including but not limited to any
implied warranty of merchantability, tness or adequacy for any particular purposes or use. Teledyne
LeCroy shall not be liable for any special, incidental, or consequential damages, whether in contract or
otherwise.

© 2020 Teledyne Test Tools is a brand and trademark of Teledyne LeCroyInc. All rights reserved.Specifications,prices,availability and deliverysubject to changewithout notice.
Product brand or brand names are trademarks or requested trademarks of their respective holders.
T3 stands for TeledyneTest Tools.
teledynelecroy.com
Company Profile
Teledyne LeCroyis a leading provider of oscilloscopes, protocol
analyzers and related test and measurement solutions that
enable companies across a wide range of industries to design
and test electronic devices of all types. Since our founding
in 1964,we have focused on creating products that improve
productivity by helping engineers resolve design issues
faster and more effectively. Oscilloscopes are tools used by
designers and engineers to measure and analyze complex
electronic signals in order to develop high-performance
systems and to validate electronic designs in order to improve
time to market.
The Teledyne Test Tools brand extends the Teledyne LeCroy
product portfolio with a comprehensiverange of test
equipment solutions. This new range of products delivers
a broad range of quality test solutions that enable engineers
to rapidly validate product and design and reduce time-to-
market. Designers, engineers and educators rely on Teledyne
Test Tools solutions to meet their most challenging needs for
testing, education and electronics validation.
Location and Facilities
Headquartered in Chestnut Ridge,New York, Teledyne
Test Tools and Teledyne LeCroy has sales, service and
development subsidiaries in the US and throughout
Europe and Asia. Teledyne Test Tools and Teledyne LeCroy
products are employed across a wide variety of industries,
including semiconductor, computer, consumer electronics,
education, military/aerospace, automotive/industrial, and
telecommunications.
Teledyne LeCroy
(US Headquarters)
700 Chestnut Ridge Road
Chestnut Ridge, NY. USA10977-6499
Phone: [phone] or 845-425-2000
Fax Sales: 845-578-5985
Phone Support: 1-800-553-2769
Email Sales: [e-mail]
Email Support: [e-mail]
Web Site: http://teledynelecroy.com/
Teledyne LeCroy
(European Headquarters)
Teledyne LeCroy GmbH
Im Breitspiel 11c
D-69126 Heidelberg, Germany
Phone: [phone]
Fax: [phone]
Phone Service: [phone]
Phone Support: [phone]
Email Sales: [e-mail]
Email Service: [e-mail]
Email Support: [e-mail]
Web Site: http://teledynelecroy.com/germany
World wide support contacts can be found at:
https://teledynelecroy.com/support/contact/#
ABOUT TELEDYNE TEST TOOLS
Distributed by:
934618-00 RevA