Teletek electronics CA62 Assembly instructions

Alarm Control Panel
CA62
Installation and Programming
Manual
WARNING
This manual contains information on limitations regarding product use and function and information
on the limitations as to liability of the manufacturer. The entire manual should be carefully read.
The information in this manual is a subject to change without notice!
C

Guarantee
During the guarantee period the manufacturer shall, at its sole discretion, replace or repair any defective product when it is returned
to the factory. All parts replaced and/or repaired shall be covered for the remainder of the original guarantee, or for ninety (90) days,
whichever period is longer. The original purchaser shall immediately send manufacturer a written notice of the defective parts or
workmanship, which written notice must in all cases be received prior to expiry of the guarantee.
International Guarantee
Foreign customers shall enjoy the same guarantee rights as those enjoyed by any customer in Bulgaria, except that manufacturer
shall not be liable for any related customs duties, taxes or VAT, which may be payable.
Guarantee Procedure
This guarantee will be granted when the appliance in question is returned. The manufacturer shall accept no product whatsoever, of
which no prior notice has been received.
Conditions for waiving the guarantee
This guarantee shall apply to defects in products resulting only from improper materials or workmanship, related to its normal use. It
shall not cover:
• Damages resulting from transportation and handling;
• Damages caused by natural calamities, such as re, oods, storms, earthquakes or lightning;
• Damages caused by incorrect voltage, accidental breakage or water; beyond the control of the manufacturer;
• Damages caused by unauthorized system incorporation, changes, modications or surrounding objects:
• Damages caused by peripheral appliances (unless such peripheral appliances have been supplied by the manufacturer:
• Defects caused by inappropriate surrounding of installed products;
• Damages caused by failure to use the product for its normal purpose; Damages caused by improper maintenance;
• Damages resulting from any other cause, bad maintenance or product misuse.
In the case of a reasonable number of unsuccessful attempts to repair the product, covered by this guarantee, the manufacturer’s lia-
bility shall be limited to the replacement of the product as the sole compensation for breach of the guarantee. Under no circumstances
shall the manufacturer be liable for any special, accidental or consequential damages, on the grounds of breach of guarantee, breach
of agreement, negligence, or any other legal notion.
Waiver
This Guarantee shall contain the entire guarantee and shall be prevailing over any and all other guarantees, explicit or implicit (includ-
ing any implicit guarantees on behalf of the dealer, or adaptability to specic purposes), and over any other responsibilities or liabilities
on behalf of the manufacturer. The manufacturer does neither agree, nor empower, any person, acting on his own behalf, to modify
or alter this Guarantee, nor to replace it with another guarantee, or another liability with regard to this product.
Unwarranted Services
The manufacturer shall repair or replace unwarranted products, which have been returned to its factory, at its sole discretion under
the conditions below. The manufacturer shall accept no products for which no prior notice has been received.
The products, which the manufacturer deems repairable, will be repaired and returned. The manufacturer has prepared a price list
and those products, which can be repaired, shall be paid for every repaired appliance.
The closest equivalent product, available at the time, shall replace the products manufacturer deems unrepairable. The current mar-
ket price shall be charged for every replaced product.

Installation and Programming Manual - СА62 Alarm Control Panel 3
CONTENTS
SECTION 1: INSTALLATION
1. Introduction............................................................................................................................................................ 4
2. Installation.............................................................................................................................................................. 5
2.1 General Information ................................................................................................................................. 5
2.2 CA62 Installation Steps............................................................................................................................ 5
2.3 СА62 Alarm Control Panel Metal Box ...................................................................................................... 6
2.4 CA62 Alarm Control Panel Plastic Box .................................................................................................... 7
2.5 CA62 Alarm Control Panel Inputs and Outputs........................................................................................ 8
2.6 Connecting of Detectors to CA62 Alarm Control Panel............................................................................ 9
2.7 Connecting of Peripheral Devices to СА62 Alarm Control Panel ............................................................. 11
2.7.1 Connecting LED and LCD Keyboards to CA62 Alarm Control Panel ........................................ 11
2.7.2 Connecting of Proxi Reader PR62 to CA62 Alarm Control Panel.............................................. 13
2.8 Using of PGM1, PGM2 and PGM3 Programmable Outputs .................................................................... 14
2.9 Using of SIREN Programmable Output.................................................................................................... 14
2.10 Connecting the CA62 Built-in Digital Communicator.............................................................................. 15
2.11 Installing of VD60 voice dialer to CA62 Alarm Control Panel ................................................................. 15
2.12 Installing of AJAX LAN Module in CA62 Alarm Control Panel ............................................................... 16
2.13 Connecting of UWE432 Universal Wireless Expander to CA62 Alarm Control Panel ........................... 16
2.14 Powering up the CA62 Alarm Control Panel .......................................................................................... 17
2.14.1 Technical Trouble Indication..................................................................................................... 17
SECTION 2: Programming
1. Programming the Software Parameters of СА62 Alarm Control Panel ............................................................ 18
2. The symbols used in this manual........................................................................................................................ 18
3. Programming of CA62 via LED or LCD Keyboard.............................................................................................. 18
4. Remote Programming of CA62 ............................................................................................................................ 19
5. Programming of Default Congurations in the CA62 Alarm Control Panel..................................................... 19
Menus for Programming the Software Parameters of CA62:
0. Engineer Parameters and Common Settings............................................................................................. 20
1. User and Manager Codes Programming ................................................................................................... 26
2. Programming of Zones............................................................................................................................... 28
3. PGM and SIREN Outputs Programming.................................................................................................... 35
4. PARTITIONS Programming ....................................................................................................................... 40
6. Programming of Communication Devices.................................................................................................. 42
6.1 General parameters .......................................................................................................................... 42
6.2 Remote programming ....................................................................................................................... 46
7. Programming of Peripheral Devices .......................................................................................................... 47
7.1 Programming of Keyboards .............................................................................................................. 47
7.2 Programming of Proxi Readers......................................................................................................... 49
SUPPLEMENTS
SUPPLEMENT А - Default Programming Tables (after RESET procedure):
TABLE 1 - Engineer Programming................................................................................................................. 50
TABLE 2 - Manager Programming ................................................................................................................. 58
TABLE 3 - User Programming........................................................................................................................ 61
SUPPLEMENT B - Examples for Security Application with CA62 ........................................................................ 62
SUPPLEMENT C - Additional Information:
Coding recordings in log events..................................................................................................................... 65
Table of protocol Contact ID transmitted codes from CA62........................................................................... 67
Table of protocol SIA transmitted codes from CA62 ...................................................................................... 68
Hexadecimal table.......................................................................................................................................... 69
SUPPLEMENT D - Algorithms for Operation of ZONES with Key-Switch Type.......................................................... 70
SUPPLEMENT E - Algorithm for Recording and Listening of Voice Messages.......................................................... 72
SUPPLEMENT F - General Connection Diagram....................................................................................................... 74
Solving of Technical Problems During Powering up of CA62............................................................................... 75

4 Installation and Programming Manual - СА62 Alarm Control Panel
SECTION 1: INSTALLATION
1. Introduction
The СА62 alarm control system is an upgraded version of СА60plus and is designed for security and protection of resi-
dential and ofce buildings. The system is based on a modular principle.
The programming of CA62 can be done by two types of keyboards (LED or LCD) or remotely via ProsTE software.
The security control is managed by means of a keyboard or a proxi reader.
General specications of СА62 alarm control panel:
Inputs: • 6 inputs for connecting detectors (5 inputs on the panel and 1 in the keyboard).
Zones: • From 6 to 12 zones with freely programmable parameters.
• Doubling the zone number in the panel by means of specic connection of the detectors.
• Individually settings for the balancing type of each input - one or two balancing resistors or zone doubling.
Partitions: • Two fully independent partitions in the system.
• Arming modes:
- Full (Arming of all zones in the system);
-Instant (Partial arming - the user is allowed to stay in some zones; the entry zone is secured and any intru-
sion will starts the alarm immediately;
- Stay (Partial arming - the user is allowed to stay in some zone; the entry zone is secured, an entry time
will start up in case of an intrusion).
• Security control by means of Proximity cards reader PR62.
• Auto Arming mode for arming the security areas in preprogrammed time.
Outputs: • 3 weak current and 1 power current programmable outputs type ОС (open collector).
• Same options for programming of all outputs.
Codes: • 4 or 6 digits access codes.
• 20 User codes, 4 Manager codes, 1 Engineer code.
• Programmable function “Ambush code” - generates a "silent" panic alarm, when the user is forced to
disarm the system.
• Supervised access of the Engineer to the programmed parameters in the system.
Events LOG: • Memory LOG for 256 events with time and date - can be viewed by a keyboard or via ProsTE software.
Report to a
Monitoring
Station:
• Built-in digital communicator for central station monitoring via telephone line. “Contact ID” and “SIA” stand-
ard protocols are supported.
• AJAX - LAN (TCP/IP) communication module.
• VD60 - Voice dialer.
Peripheral
Devices:
• Up to 4 keyboards - LED and/or LCD models.
• Up to 2 proximity cards readers - PR62.
• Supported keyboards for CA62:
- LED61 - Keyboard with LED display up to 6 zones.
- LED62 - Keyboard with LED display up to 12 zones, supports operation with 2 Partitions (A and B).
- LED63 VG SE - Keyboard with LED display up to 12 zones, supports operation with 2 Partitions (A and B).
- LCD62 - Keyboard with icon LCD display up to 6 zones.
- LCD62В - Keyboard with icon LCD display up to 6 zones (blue backlight of the display).
- LCD63 - Keyboard with icon LCD display up to 6 zones with option for voice messages.
- LCD63SE - Keyboard with icon LCD display up to 12 zones with option for voice messages, supports
operation with 2 Partitions (A and B).
- LCD64 - Keyboard with icon LCD display up to 12 zones, supports operation with 2 Partitions (A and B).
• All keyboards have 1 built in zone and quick access buttons.
• Flexible programming of the buttons functions for arming and disarming the partitions in the system.
Programming: • The alarm panel parameters can be programmed from every keyboard (LED or LCD) in the system.
• Programming via PC with ProsTE software (RS232 serial bus) or via telephone line.
• 4 default congurations of the system parameters, used for basic programming of 3 typical and 1 general
system congurations.
Technical
Specications:
• Transformer - 17 VAC, 17 VA.
• Accumulator charger - 13.8 V, 1A, electronic overload protection.
• Back-up power supply - accumulator 12 V, 7,2 Ah.
• Current consumption - up to 100 mA for the control panel.
• Power supply for detectors - 13.8 V, 1A, electronic overload protection.
• Power supply for additional devices - 13.8 V, 1A, electronic overload protection.
• Operating temperature - from 0°C to +50°C.
• ABS Plastic box - dimensions: 315 х 260 х 80 mm.
• Weight - 2.42 kg.

Installation and Programming Manual - СА62 Alarm Control Panel 5
2. Installation
2.1 General Information
The CA62 Alarm control panel was designed and tested in compliance with electromagnetic compatibility standards.
The following recommendations need to be observed for the proper performance of the alarm station:
➢ Ensure the alarm system is properly earthed (grounded).
➢Insulate the high and low voltage cables and use different input openings on the box.
➢Avoid any loops of connecting wires within the very box and in their passage over or under the printed-
circuit boarding.
➢Additional relays MUST NOT be placed in the CA62 Alarm control panel box as these may generate
electromagnetic interference when switched.
- Use only relays with good insulation between contacts and the winding.
- Relays, connected to outputs with an open commutator, must be designed to accommodate
a 12 V DC driving voltage and an impedance at the winding greater than 400Ω.
➢The cable connecting the control panel and the keyboard is quadruple.
It is strongly recommended not to: use this cable to make other connections - connect to a telephone
line, Flash-lamps control signals, sirens or relays.
➢Avoid channels or cable forms that contain high voltage cables when placing the connecting shielded ca-
bles. This is very important in cases where such cables are being used to power electric motors, uorescent
lamps or triple-phase voltage. Where the above is not possible, use only shielded cables, where the shield is
grounded only in the alarm system box.
2.2 СА62 Installation Steps
We recommend during the installation of СА62 to follow the next installation steps:
➢ Carefully plan the security system - the type, number and location of detectors, the location of all peripheral
devices, communication modules and the control panel, the type and length of connection wires and cables,
etc.
➢ Mount all system elements - СА62 control panel, detectors, peripheral devices - keyboards and proximity
card readers, indoor or outdoor sirens. During the mounting follow the described in item 2.6 connection
diagrams and choose the type of zone balancing - with 1, 2 or 3 resistors.
Attention: The numeration of the keyboards sequence is important, you have to follow strictly the order 1 to 4.
The different keyboard models supported by CA62 and their connection to the control panel are described in
details in item 2.7.
➢ Power up the system as follow the steps in item 2.14. Check the normal system operation - there is
communication between the control panel and the keyboards, and the LED indication of the detectors in the
system is working.
➢Program the default conguration type 0, 1, 2 or 3 - the most suitable for your alarm system installation.
Details for default congurations are described in SECTION SUPPLEMENTS of this manual.
➢Program all other necessary parameters concerning your alarm system installation, as follow the order:
peripheral devices, zones, partitions, programmable outputs (PGM), communicator, dialer, user and manager
access codes and attributes.
➢ Test the efciency of your system installation.

6 Installation and Programming Manual - СА62 Alarm Control Panel
2.3 СА62 Alarm Control Panel Metal Box
Figure 1. Situation of СА62 alarm panel in metal box.
Figure 2. Side view and mounting of universal metal box.
CA62 Control panel

Installation and Programming Manual - СА62 Alarm Control Panel 7
2.4 СА62 Alarm Control Panel Plastic Box
Figure 3. Opening the CA62 plastic box and template for wall mounting.
Figure 4. Situation of СА62 control panel in plastic box.
1 - Central support opening (behind PCB)
2 - Support openings
3 - CA62 Control panel
4 - Mains power supply terminal
5 - Main cable opening
6 - Additional cable openings
7 - Mains power supply opening
8 - Tamper button for box self-protection

8 Installation and Programming Manual - СА62 Alarm Control Panel
2.5 CA62 Alarm Control Panel Inputs and Outputs
Figure 5. CA62 control panel inputs and outputs.
Terminals description of СА62 control panel:
• AC - Power supply from 17V / 17VA mains transformer
• - “EARTH”
• AUX - Power supply -PGM for detectors with consumption up to 1А
• +PGM - Power supply for additional devices with consumption up to 1А
• PGM1, PGM2, PGM3 - Programmable outputs
• SIREN - Siren programmable outputs (PGM4 by default)
• Z2, Z3, Z4, Z5, Z6 - Zone inputs (Z1 zone is in the keyboard))
• COM - Common mass of the zones
• A, В - Terminals for telephone line connection
• А1, В1 - Terminals for connecting a telephone set
• RED, BLACK - Keyboard power supply
• GREEN, YELLOW - Interface between the panel and the keyboard
• F1 BATT - Battery fuse 0.75А, Resettable (PTC)
• F2 PGM - Additional device 0.5А mains fuse, Resettable (PTC)
• F3 AUX - Fuse for powering sensors, programmable outputs and keyboards 0.5А, Resettable (PTC)
• BATT - Battery cables for accumulator with parameters 12V / 7.2 Ah
• JPRG - Jumper for hardware RESET and default parameters recovery
• GPIO - Interface connector for programming
• EXPAND - Terminal for expander modules (Voice dialer VD60)

Installation and Programming Manual - СА62 Alarm Control Panel 9
2.6 Connecting of Detectors to CA62 Alarm Control Panel
The security system is mounted with detectors with relay contacts.
Fire alarm detectors supplied with relay outputs can also be used.
There are three possible options for connecting of detectors to the CA62 zone inputs. The type of balancing for each
input is programmed separately at ADDRESSES 2zz6, where "zz" is the zone number - from 02 to 06.
The possible options for connecting the detectors and for balancing the zones are shown on Figure 6: a) Connecting
Detectors with One Balancing Resistor, b) Connecting Detectors with Two Balancing Resistors and c) Connecting De-
tectors with Three Balancing Resistors (zone doubling with connecting two groups of detectors/ zones to one input).
The zone doubling allows to the zones with numbers 2, 3, 4, 5 and 6 of СА62 control panel to be connected two groups
of detectors, as the rst group is terminated with 1 kΩ resistor, and the second - with 2.2 kΩ. When a zone doubling
is realized in the system, the number of the zone for the second group of detectors, represents the number of related
zone + 6.
Use the supplied 1 kΩ resistors to balance the zones. The balancing resistors are installed on the last detector of the
circuit. The zones, which shall not be used, are terminated with one 1 kΩ resistor at the terminals of the CA62 Control
Panel, irrespective of the chosen type of zone balancing. A second way for temporary termination of the unused zones
is as program them as 0.Unused on the respective address - see the description of ADDRESS 2010.
After the initial power up of the control panel, the zone balance type has to be programmed. By default only 1 balancing
resistor is used.
The hardware implementation of Zone 4 of the panel permits performance in pulse count mode, suitable for connecting
a rolling shutters detector. This mode counts short pulses - 2 to 4 ms for a period of 20 seconds. The rst pulse starts a
20-second countdown during which pulses are expected to be received. Their number is assigned at ADDRESS 2047 of
the engineer program. An alarm signal is emitted when this number is reached within the time of 20 seconds. Otherwise
the pulse counter will be zeroed after the time of 20 seconds expires.
Activating the pulse count mode will automatically start when a number other than 0 is keyed in at ADDRESS 2047 of
the engineer program. The connection option of a rolling shutters detector to ZONE 4 is shown on Figure 6 d).
The possible options for connecting re detectors and balancing the zones are shown on Figure 7.
а) Connecting Detectors with
One Balancing Resistor
Connecting up to n detectors Connecting up to 4 detectors
b) Connecting Detectors with Two Balancing Resistors
c) Connecting Detectors with Zone Doubling
d) Connecting of rolling shutters detector to Zone 4, in zone doubling mode.
Figure 6. Options for connecting detectors to the CA62 control panel.

10 Installation and Programming Manual - СА62 Alarm Control Panel
Connecting a re detector with one balancing resistor
Connecting a re detector with two balancing resistors
a) Connecting a re detector with a relay in the base
b) Connecting of two re detectors to a doubling zone.
Figure 7. Connecting a re detector to CA62 alarm control panel.
The programmable output
must be programmed
as and the active
status must be +12 VDC.
Fire Reset
Fire
detector
base
*
* You can use also
two R=510Ω (one R is
connected to every fire
detector), instead of
one R=1k.

Installation and Programming Manual - СА62 Alarm Control Panel 11
2.7 Connecting of Peripheral Devices to СА62 Alarm Control Panel
2.7.1 Connecting LED and LCD Keyboards to CA62 Alarm Control Panel
Two types of keyboards can be used to control and program the СА62 alarm panel:
• LED keyboards -models LED61, LED62, LED63VG SE
• LCD keyboards - models LCD62, LCD62B, LCD63, LCD63SE, LCD64
Figure 8. Basic view of LED and LCD keyboards.
Symbols to Figure 8:
. Status LED indication.
. Buttons for programming and controlling of CA62 control panel.
. Protective cover (open).
. Microphone.
. LCD display.
Attention: The LCD display is different for the listed keyboard models:
Models: LCD62, LCD62B, LCD63VG Model: LCD63SE, LCD64
For detailed description for indication and operation of all keyboard models refer to their individual manuals.
LED61
LED62
LCD62
LCD62B / LCD64
LCD63, LCD63SE
LED63VG SE

12 Installation and Programming Manual - СА62 Alarm Control Panel
All keyboard models are factory equipped with 4 terminals for connecting to СА62 control panel and two other terminals
for connecting to ZONE 1. Note: At LED61 keyboard, the input for ZONE 1 is equipped with two 10-cm long wires - black
and white for the bus connection. These terminals are marked with the respective colors.
The colors must be observed when connecting the keyboards to the СА62 Control Panel (see Figure 9). Note:
The connection in the connection below is principled. Note that in some keyboards the terminals for connecting to
ZONE 1 could be situated above the terminals for connecting to the control panel.
The zone cables are white and black in color. The zone in the keyboards HAS NOT to be balanced (except LED62
and LED63VG SE keyboards - the keyboard zone can be balanced with setting the ZONE EOL jumper, see the
jumpers explanation on Figure 10b). The zone in all model keyboards HAS NOT to be programmed as double
zone also. When more than one keyboard are connected to the control panel, each keyboard have to be assigned with
individual zone number - 1 or 7. Activating any keyboard zone shall be regard as an activation of ZONE 1 or ZONE 7,
according the individual programming.
No more than 4 keyboards (irrespective of their type) can be connected to one control panel. Each keyboard must be
assigned an individual address, by placing the jumper on the keyboard at its respective place (see Figure 10а). The
individual address ensures TAMPER event identication, whenever the TAMPER switch of the respective keyboard is
turned on.
The individual address of each keyboard is assigned with the help of a jumpers. Following the table (see Figure 10а)
the respective address could be programmed. The individual address of each keyboard in the system can be checked
at ADDRESS 7000 from the Engineer menu (see page 47).
The JT jumper must be placed where only one keyboard has been connected. Where more than one keyboards are
connected, the JT jumper should be placed on the most distant one. The JT jumper is set by default.
The cable connecting the LED61 Keyboards to the CA62 Control Panel must be no longer than 250m and have a cross-
section of no less than 0.25mm.
Keyboard:
ZONE 1
DETECTORS WIRES
CA62 control
panel terminals
LCD64
(SE)
Figure 9. Connecting keyboards to CA62 control panel.
NOTE: The JT jumper must be set in the most far unit in the bus.
1234
J0
J1
J2
Address
Jumper
Jumper location for
keyboard models:
LED61, LCD62,
LCD62B, LCD63,
LCD63SE, LCD64
Legend:
- The jumper is removed;
- The jumper is set
Figure 10a. Table for keyboard address programming.
Jumper location
for keyboard
models:
LED62
LED63VG SE
NOTE: The JT jumper
must be set in the most
far unit in the bus.
The LED keyboard zone is not balanced.
The jumper Zone EOL is removed.
The zone has two states:
• zone closed (the switch is closed)
• zone open (the switch is open)
The LED keyboard zone is balanced.
The jumper Zone EOL is set.
The zone has three states:
• zone closed (the switch is closed) - item 1
• zone open (the switch is open) - item 1
• tamper - items 2 and 3
1)
2) 3)
Figure 10b. Jumper location and zone balancing of LED62 and LED63VG SE keyboards.
The parameters and the functions of the buttons for each keyboard can be programmed at ADDRESSES 70xx, accord-
ing to the set with jumper address of the keyboard.

Installation and Programming Manual - СА62 Alarm Control Panel 13
2.7.2 Connecting of Proxi Reader PR62 to CA62 Alarm Control Panel
The PR62 proximity card reader was designed to control security in the systems integrated within the CA62 Control
Panel. The excellent card reading distance, the triple color indications, supplemented by the sound indicator, the inte-
grated output, as well as the ne design, all make the PR62 any attractive supplement to the security system.
The PR62 can be connected to the terminals RED, GREEN, YELLOW and BLACK of the CA62 together with the
mounted keyboards. Up to two proximity readers can be included within one security system. Programming the various
addresses onto the readers will provide identication by the TAMPER of each of these. The Table for Address Program-
ming is provided on Figure 11.
The proximity-card enables to arm and disarm the system, as well as to control the electric lock (key-switch) via inte-
grated output. The internal structure, and the permissible output currents, are provided in Fig. 11.
It is possible that only proximity-card readers be included in a system without having an installed keyboard. In such
systems this would hinder current programming of parameters and cards, as well as Log Review and Technical Trouble
indications. Portable LED or LCD type keyboards can be used to accomplish such tasks.
Up to 24 cards can be assigned to one security system - one card for each of the 20 users and 4 cards for the Managers
in the system.
The Managers in the system are allowed to program the performance of the cards.
Arming and/or disarming rights must be assigned for the respective user code.
The user may not be designated a code combination. In such case the only means to control the security system would
be the proximity-card.
The parameters of the proximity card readers in the system can be programmed at ADDRESSES 71хх, according to the
set with jumper address of the proxi reader.
Figure 11. PR62 Proximity card reader installation and connection diagram.
* The JT jumper must be set in
the most far unit on the bus.
LED indication:
- green - the card is recognized or
required action is done,
- red - the card is not recognized or
required action is rejected,
- yellow (LED blinks) - ready.
Internal structure of built-in PGM
PGMx terminal
Permissable currents:
- from +12 V - up to 10 mA
- towards GND - up to 100 mA
The output activates for 2
seconds after the recognised
card is drown back.
Two color LED indicator
Lock
Mounting openings
Signal cables
openings
1 2
J1
J2
Address
Jumper
Setting the address of PR62
Legend: - The jumper is removed;
- The jumper is set
PPPProxi CA62

14 Installation and Programming Manual - СА62 Alarm Control Panel
2.8 Using of PGM1, PGM2 and PGM3 Programmable Outputs
The СА62 Alarm panel PGM1, PGM2 and PGM3 outputs have a programmable active level. This allows them to be used
to transmit control signals towards external devices (e.g. a block siren input) or to directly control low-powered external
devices (e.g. relays, LED, etc.).
The internal structure of all PGMs is the same and is shown on Figure 12 a).
Figure 12 b) shows the connection of the relay and a light-emitting diode to the PGM. The active level of this connection
is low.
Figure12. а) Internal structure of Figure12. b) Controlling light-emitting diode and
programmable PGMx output relay using PGM1 and PGM2 outputs
2.9 Using SIREN Programmable Output (PGM4)
The СА62 Alarm panel SIREN output has a programmable active level. With the default conguration the output is
with SIREN and POLARITY set attributes, which can be programmed at ADDRESS 3041. The output is activated in
case of alarm event in the system.
The internal structure is identical to the one shown in Figure 12 a) and we should point out that the transmitter can pass
through to GND electricity of up to 1 A.
Figure 7 shows how to connect SR110, SR120, SR200 and SR300 sirens using the SIREN output.
a) Connecting SR110 using a double-wire b) Connecting SR120/SR200
using a double-wire
c) Connecting SR120/SR200/SR300 using triple-wire.
Figure 13. Controlling sirens using SIREN output.
PGMx terminal
Permissible current:
- from +12 V - up to 10 mA
- towards GND - up to 100 mA
For SIREN output the
current supplied to GND
is up to 1A.
The BLOCK jumper
in SR120 (BL in SR200)
must be set on.
The BLOCK jumper
in SR120 (BL in SR200)
must be removed.
The jumper BlockA -/+ determines the level of
the block signal: set jumper - high level (12V);
removed jumper - low level (GND)

Installation and Programming Manual - СА62 Alarm Control Panel 15
2.10 Connecting the CA62 Built-in Digital Communicator
2.11 Installing of VD60 voice dialer to CA62 Alarm Control Panel
The “VD60” Voice Telephone Dialer module supplements the СА62 Alarm Control Panel, which serves to transmit alarm
event messages to the user, under the form of eight pre-recorded voice messages, of up to 4 sec. each. Two message
types are supported - by zone or by event (see description of ADDRESS 6035).
Turn off the power supply in order to connect the PCB of the voice telephone dialer to the EXPAND socket of the CA62
Control Panel (1). Fix the PCB onto the pre-mounted plastic spacers (2). The telephone line should be connected to
terminals A and B of the СА62 Control Panel. Polarity need not be observed.
The telephone device can be connected to terminals A1 and B1 of the СА62 Control Panel with no need of observing
polarity.
The voice dialer can simultaneously operate with the built-in digital communicator.
The dialer has one LED status indicator - PLAY/RECORD and BUSY, and one single digit LED display indicating the
number of the current message. Use the MSG key to switch-over between messages. Use the PLAY key to reproduce
messages when the REC jumper is turned off, or to record when it is turned on. You can record voice messages at AD-
DRESS 6030, as use the detailed working algorithm described at APPENDIX Е. A speaker (8-16 ohms) for listening to
recorded messages can be connected to the SP socket.
The voice dialer parameters can be programmed in the engineering menu at ADDRESSES 603х.
Figure 15. Installing the VD60 Voice Telephone Dialer.
Telephone line
Telephone device
Figure 14. Connecting the CA62 built-
in communicator
The telephone line is connected to A and B terminals on the
CA62 Control Panel with no requirements to observe polarity
(Figure 14). The telephone device is connected to A1 and B1
terminals on the CA62 Control Panel with no requirements
to observe polarity (Figure 14). The parameters of the digital
communicator are engineer programmed. It is not necessary
to install additional components if the built-in communicator
is not to be used.
You can test the Built-in Digital Communicator working ef-
ciency at ADDRESS 0023 described on page 23.

16 Installation and Programming Manual - СА62 Alarm Control Panel
2.12 Installing of AJAX LAN Module in CA62 Alarm Control Panel
AJAX Module is an additional accessory for built-in installation in CA62 or any other security or re control system. It
transmits the system status to Monitoring centre or to the User via Internet. The AJAX module enables easy monitoring
and transmitting of alarm events occurring in the security system to existing Monitoring centre using standard monitor-
ing software.
For more information please refer to the distributor of this equipment.
For the installation of AJAX LAN module in the CA62 universal plastic box
refer to sequence shown in Figure 16 as follow the steps:
- Break off the pins from the plastic box.
- Fix the mounting holes to the respective pins and carefully push down.
- Fix the module to the plastic box with the screw from the spare parts kit.
Figure 16. Installing of AJAX LAN Module.
For the connection between AJAX LAN mod-
ule and CA62 alarm control panel refer to
Figure 17, as follow the steps:
 - With Power supply OFF, connect the
AJAX module to the CA62 by means the
interface cable (Note: the interface cable is
not included in the spare parts kit for CA62.)
 - Connect LAN cable for Internet connec-
tion.
 - Place a reset jumper.
 - Turn the Power supply ON and wait
for 5 seconds in order to congure and to
obtain the default factory parameters.
 - Remove the RESET jumper.
Figure 17. Connecting of AJAX LAN
module to CA62.
2.13 Connecting of UWE432 Universal Wireless Expander to CA62 Alarm Control Panel
UWE432 is a universal device for expanding existing wired alarm security systems. UWE432 communicates by means
of two-way radio connection with the AVA series wireless devices. The UWE432 supports up to 32 AVA series wireless
devices. Attention: The panel should be programmed to operate in double zone connection mode (at addresses
20х6, х - from 2 to 7, "4. Doubling" parameter is set). It is obligatory to set a jumper on connector MODE at
UWE432 main board!
Figure 18. Connecting UWE432 universal expander to CA62 alarm control panel.
ATTENTION: The connecting between AJAX LAN module and
CA62 alarm control panel MUST BE done only with power
supply OFF and set RESET jumper on the AJAX module!

Installation and Programming Manual - СА62 Alarm Control Panel 17
In1 - Input for resetting wireless re detectors (time for reset ≥ 2 seconds), the active state towards GND is 0V; In2 -
Input for wireless siren control (time for reset ≥ 2 seconds), the active state towards GND is 0V; In3 - Used only in case
RC102TE remote control is enrolled to UWE432 receiver module; this is an input for monitoring of the control panel
status; Out1 - Relay output (NO) for Low Battery and Lost Device state of wireless devices; Out2 - Relay output (NC) for
TAMPER state of wireless devices and the UWE432 box; Connect to a TAMPER type zone of the control panel.
More information about UWE432 functions and programming you can nd in its installation instructions.
2.14 Powering up the CA62 Alarm Control Panel
The system should be powered-up only after it is installed and all necessary devices have been connected - control
panel, keyboard, detectors, etc.
Follow the next installation procedure when power-up the CA62 system for the rst time:
➢Set the JPRG jumper (Figure 5) on CA62 control panel, in order to congure the control panel default pa-
rameters (the factory settings).
ATTENTION: The CA62 alarm control pane supports 4 different default congurations. With every full hardware
system reset (jumper JPRG is set) the parameters for default conguration 0 will be set. The special of the
default conguration 0 is that all zones in the system are disabled (the 0.Unused type is set for all), the zone
balancing is with one resistor in the circuit and so on. For details for settings of the default system congura-
tion 0, see SECTION 2 - Programming.
➢Supply 220V mains power. The keyboard emits a short sound signal or series of short beeps according
the used model. In case of a LED keyboard the light-emitting diodes on the display blink. When a LCD
keyboard is used the display will light up in blue or orange.
➢Remove the JPRG jumper. In normal operation mode - all detectors in the security system are inactive
and there are no violated anti-TAMPER chains - the RDY LED lights up in green. The station now has been
programmed with the default conguration 0.
If you operate with LCD keyboard the display is looking different according the model:
Models: Model:
LCD62, LCD63SE
LCD62B, LCD64
LCD63
➢Use the red (+) and black (-) cables to connect the battery to the station.
All light-emitting diodes will blink and a sound signal will be heard where the keyboard is open or incorrectly connected.
Where there is an open zone or an open TAMPER for any zone, the LED for the respective zone (at LCD keyboards the
zone number is enclosed in brackets) together with the MEMORY or TAMPER LEDs on the display will light up (at LCD
keyboards lights up TRBL LED and symbol "wrench" is blinking).
ATTENTION! An open anti-sabotage chain (TAMPER) in the security system will sound the siren. To stop the
siren enter Manager code 0000. The respective zone LED remains permanently lit whereas the TAMPER LED will
blink. Remove the failure - the TAMPER LED remains permanently lit. Enter code 0000 again to clear the alarm
event from the memory.
2.14.1 Technical Trouble Indication
Any technical trouble in the panel will light up the Trouble indicator (blinking TRBL LED and/ or symbol “wrench” accord-
ing of the keyboard model). To view these problems enter the 0000 manager code and single-press ENTER. The display
will indicate a list of current problems. The indications and their meaning are shown in the table below:
LED Keyboard
LED lighting up
LCD Keyboard
Digit enclosed in brackets
Technical trouble
(LED or symbol is blinking)
B(1) No 220 V power supply
C(2) Battery low
D(3) Fuse burned
E(4) No telephone line
F(5) No communication available
G(6) Active TAMPER within the system
Trouble mode indication (Technical Trouble)

18 Installation and Programming Manual - СА62 Alarm Control Panel
SECTION 2: PROGRAMMING
Programming the Software Parameters of СА62 Alarm Control Panel
The system can operate with 4 or 6 digit codes. If a 6 digit code is set at ADDRESS 1001 at the end of every valid code
an extension "00" is automatically added. Next a new 6 digit code combination can be programmed.
The respective parameters can be congured from a LED or LCD keyboard or remotely by means of connected to the
system a personal computer via a telephone using the ProsTE Software.
Symbols used in this manual
For more clear presentation of the programming with the two types (LED and LCD) keyboards and for easy perform-
ance of the information in this manual, the following symbols for indicating of active (enabled) and inactive (disabled)
parameters in the engineering programming menus are used:
Indicator Parameter state LED LCD
ZONES Active (enabled parameter) B - Lights on (1) - Number enclosed in brackets
Inactive (disabled parameter)  - Lights off 1 - Number without brackets
Keyboard programming
Entering the system engineer code will initiate the CA62 Alarm System programming mode for the engineer param-
eters. After restoring the default parameters (system RESET) the engineer code will remain 7777.
When you enter the engineer programming menu the indication of the used keyboards will be as follows:
- LED Keyboards - the LEDs RDY (green), ARM (red), TRBL (yellow) and BPS (red) are blinking together. At LED62
keyboard the symbols “lighting”, “wrench” and “sheet” are blinking together.
- LCD Keyboards - the LEDs RDY (green), ARM (red) and TRBL (yellow) are blinking together. The symbol
blinks together with symbol . At LCD63SE keyboard the symbol is blinking, and at the middle tower of the castle
the symbol is steady.
At LCD type keyboards, after entering engineer programming mode the symbol starts blinking at the place of the
clock. Every entered digit of the ADDRESS stop blinking and stays steady, the symbol next to it will be continue blink-
ing, which means, that the system is waiting for entering the next digit of the 4 digit ADDRESS.
After entering 4 digit number of a valid ADDRESS a conrmation sound signal will be heard.
After entering of a 4 digit ADDRESS the engineer can program the respective system parameter. Use the provided in
this section tables with detailed descriptions of all available ADDRESSES in the system. You can use also the tables in
SUPPLEMENT A for quick reference. All entered parameters have to be conrmed with pressing the ENT button. When
reviewing the programmed parameters it is recommended to exit any given address by single pressing the CLEAR
button. This function will leave the introduced parameters unchanged. In case the programmer is disoriented in the en-
gineer menu, it is recommended to exit the menu by double clicking the CLEAR button and to begin programming the
station parameters from the start.
ATTENTION: The CA62 Alarm System engineer parameters programming mode can begin only when the sys-
tem is in disarmed mode! When there are several (up to 4) keyboards connected to the control panel in the sys-
tem you can program parameters only from this one where the engineer code has been entered. The indication
of all other keyboards will show that the system is in engineer programming mode, but you can not program
parameters with them.
How to read the information in the tables below:
ADDRESS 0001 - HARDWARE RESET ENABLE
Reset
Enable
Disables or enables the hardware RESET of the alarm station. Specialized service is
required where the hardware RESET is disabled and the engineer code is obscure.
The parameter status can be changed with pressing of random button of the keyboard.
NO The hardware RESET is disabled.
Indication
LED

LCD
1 2 3 4 5 6
YES The hardware RESET is enabled.
Indication
LED

LCD
(1) (2) (3) (4) (5) (6)
Default settings - YES
Default conguration settings for that programming menu
Programming
menu param-
eters
ADDRESS
Number
Name of the pro-
gramming menu
Description of the pro-
gramming menu

Installation and Programming Manual - СА62 Alarm Control Panel 19
For easy nding the information in the programming tables, the ADDRESSES are organized in 7 separate sections:
The rst digit of the ADDRESS structure describes:
0 - Programming the engineer and common system parameters;
1 - Programming the access codes in the system;
2 - Programming the zone parameters in the system;
3 - Programming the PGM outputs in the system;
4 - Programming the partitions in the system;
6 - Programming the parameters of the communication devices in the system;
7 - Programming the parameters of the peripheral devices in the system.
The second and the third digit in the ADDRESS structure logically separate the unit number for every sec-
tion - for example 01, 02 and so on are zone numbers. The same principle is right for the sections for program-
ming the parameters of access codes, zones, PGM outputs, partitions, communication and peripheral devices
in the system.
The forth digit in the ADDRESS structure is the number of a parameter for a specic system resurse.
Example for ADDRESS structure reading:
Besides the information for activating and deactivating of the system parameters, for some menus are shown and con-
crete examples for the status and indication of the LCD keyboards.
Basic sequence in operation when programming the Engineer menu:
Remote programming of CA62
To access a ProsTE software program system requires an ID number and a station ID number. After restoring the default
parameters these numbers will be the same and are 1234. In order to provide access to the system from the central
station enter the correct number of the central station at ADDRESS 6901 (PC ID).
A 24-hour period automatically begins after default parameters are restored during which the UDL communication with
the system is enabled even when the "ring number" parameter is zeroed at ADDRESS 6904 (with set 0 number, the
UDL communication will starts after receiving of 7 rings). After the initial 24-hour period, the UDL communication with the
system will enabled only if the "ring number" parameter set at ADDRESS 6904 is different from zero.
If during the 24-hour period the system is power off (together the main power supply and the battery), at the next power
on the started already 24-hour period will be disabled and the UDL communication will be enabled only if the "ring
number" parameter set at ADDRESS 6904 is different from zero.
If during the 24-hour period the engineer enters the ADDRESS 6903 and exit it by pressing the ENT button (with conr-
mation), then the 24-hour time period and this case will be disabled.
Detailed working instructions for the ProsTE software program are provided in the built-in Help les. The connection
between the local computer and the CA62 control panel is via a specialized module (the module is not included in the
CA62 equipment and is sold as a separate product.)
The details listed in this manual apply to all parameters for remote system programming.
Programming of Default Congurations in the CA62 Alarm Control Panel
The system supports 4 separate default congurations with set parameters. Enter a number of default conguration
(0-3) at ADDRESS 1000 in the engineer programming menu - see item 1. User and Manager Codes Programming. At
SUPPLEMENT B are shown examples for using the default congurations in the system.
ATTENTION: With realizing full hardware reset, in the system automatically will be set the
default conguration 0 parameters!
The default conguration 0 parameters are described in details in Table 1 (SUPPLEMENT
A) and they are described in ADDRESSES tables below.
Section for zone
programming
Parameter for
programming the
zone type
Zone number

20 Installation and Programming Manual - СА62 Alarm Control Panel
0. ENGINEER PARAMETERS AND COMMON SETTINGS
ADDRESS 0000 - CHANGING THE ENGINEER CODE
Engineer
code
A new access code to the alarm station engineer parameters can be assigned at this address.
Note: If the 6-digit long access code is set, the combination "00" automatically will be added at the end
of all valid codes in the system (see also the description of ADDRESS 1001).
Indication
LED

LCD
1 2 (3) (4) (5) (6)
The light-emitting diodes 3, 4, 5 and 6 on the keypad display light up. These go out one by one as the
new code is entered. The new code has to be entered a second time.
Default settings - 7777
ADDRESS 0001 - HARDWARE RESET ENABLE
Reset
Enable
Disables or enables the hardware RESET of the alarm station. Specialized service is required where
the hardware RESET is disabled and the engineer code is obscure.
The parameter status can be changed with pressing of random button of the keyboard.
NO The hardware RESET is disabled.
Indication
LED

LCD
1 2 3 4 5 6
YES The hardware RESET is enabled.
Indication
LED

LCD
(1) (2) (3) (4) (5) (6)
Default conguration - YES
ADDRESS 0002 - RESTORING DEFAULT PARAMETERS (SOFTWARE RESET)
Default
settings
Restoration of default settings of the station. The buttons 1, 2, 3, 4, 5, 6 are pressed in succession and
conrmed with the ENTER button.
ADDRESS 0003 - RESTORING DEFAULT MANAGER CODE (PARTIAL SOFTWARE RESET)
Partial reset
Restoration of the default manager code. Buttons 1, 2, 3, 4, 5, 6 are pressed in succession and con-
rmed with the ENTER button.
The station restores the default 0000 manager user code.
ADDRESS 0010 - AUTHORITY TO ARM USING A ONE PUSH-BUTTON (QUICK ARM)
Quick ARM
Enable
A quick Arming mode using one button, without need to enter a valid user code is assigned at this ad-
dress. The assigning can be done for PARTITION A, PARTITION B or for both partitions.
The parameter is activated with pressing a digit number corresponding to the partition number - 1 for
PARTITION A and 2 for PARTITION B. Next pressing of the button will deactivate the parameter.
PARTITION
A
Quick Arming of PARTITION A without legal user
code.
Indication
LED

LCD
(1) 2 3 4 5 6
PARTITION
B
Quick Arming of PARTITION B without legal user
code.
Indication
LED

LCD
1 (2) 3 4 5 6
Default conguration - PARTITION A, PARTITION B