Tennant 9015013 Training manual

IB 9015087 (04- 2017) 1
INSTRUCTION BULLETIN
No. 9015087
Machine: M17
Published: 04- 2017
Rev. 00
NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the
Parts List in the appropriate place in the machine manual for future
reference. Retaining the Parts List will make it easier to reorder
individual parts and will save the cost of ordering an entire kit.
NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
Installation instructions for kit number 9015013
SYNOPSIS:
This kit contains the parts needed to replace the hydraulic pump on M17 sweeper- scrubbers.
Please follow step-by-step instructions.
SPECIAL TOOLS / CONSIDERATIONS: NONE
(Estimated time to complete: 1 hour)
When assembling / disassembling hydraulic components:
1. Thoroughly clean outside of hydraulic components before disconnecting hydraulic hoses or fittings
and flush hoses and fittings with air, solvent, or hydraulic fluid and cap disconnected hoses or open
ports to prevent contaminants from entering system.
2. Mark hydraulic hoses with locations of where they are attached. Markings make it easier to reconnect
hoses to proper locations.
3. Discard all hydraulic fluid drained from the system. Use only new approved hydraulic fluid to replenish
hydraulic reservoir. Hydraulic fluid is potentially dangerous to the environment. Obey all federal, state,
and local laws/regulations governing the disposal of environmentally hazardous materials when
disposing hydraulic fluid.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials, used machine components
such as batteries and fluids in an environmentally safe way according
to local waste disposal regulations.
Always remember to recycle.
PREPARATION:
FOR SAFETY: Before leaving or servicing
machine, stop on level surface, turn off
machine, and remove key.
1. Disconnect the battery cable from the
machine.
WARNING: Always disconnect battery
cables from machine before working on
electrical components.
2. Remove the hopper cover from the hopper.
Sett he hopper cover aside.
INSTALLATION:
1. Disconnect the wire harness from the
hydraulic pump.
2. Disconnect the hydraulic hoses from the
hopper lift cylinder from the hydraulic pump.
Plug the disconnected hoses. Note hose
locations on the hydraulic pump. (Fig. 1)
3. Remove the hydraulic pump from the pump
mounting bracket. Set the M10 hex screws
and flat washers aside. Discard the removed
hydraulic pump. (Fig. 1)
4. Install the Deutsch connector (2) onto the new
hydraulic pump (1). (Fig. 2)

IB 9015087 (04- 2017)2
5. Install the hydraulic pump (1) onto the pump
mounting bracket. (Fig. 1)
6. Connect the hoses from the hopper lift
cylinder to the hydraulic pump (1). (Fig. 1)
7. Connect the wire harness to the hydraulic
pump (1).
8. Fill the hydraulic pump (1) with hydraulic fluid
until the hydraulic fluid is at the correct level.
(Fig. 1)
9. Reconnect the battery cable to the machine.
10. Turn on the machine, raise and lower the
hopper several times, lower the hopper, and
turn off the machine. Check the hydraulic
pump / hydraulic hose connections for leaks.
11. Check the hydraulic level in the hydraulic
pump (1). Add hydraulic fluid as necessary
until the hydraulic fluid is at the correct level.
The hopper must be completely lowered
before checking hydraulic level / adding
hydraulic fluid.
1
FRONT
Hopper lift cylinder
Set M10 hex screws
(Qty. 2) / flat washers
(Qty. 2) aside
Pump mounting
bracket
Check hydraulic fluid level in hydraulic pump (1).
Hopper must be completely lowered before checking
hydraulic level / adding hydraulic fluid.
FIG. 1

IB 9015087 (04- 2017) 3
Deutsch connector (2)
FIG. 2
Bill Of Materials For Pump Kit, Hyd, Cyl, NA/CE, Afmkt [M17] - 9015013
Ref.
Tennant
Part No. Description Qty.
o19015013 )Pump Kit, Hyd, Cyl, NA/CE, Afmkt [M17] 1
Y2 1222705 Connector, Ele [Deutsch, Dtp, 4M, Kit] 1
Y31225464 Label Set, Info/Hzrd, Pyc [T17/M17] - (Labels already installed) 1
TENNANT COMPANY
P. O. Box 1452
Minneapolis, MN 55440-1452