Tennant T12 Training manual

IB 9010947 (05- 2013) 1
INSTRUCTION BULLETIN
No. 9010947
Machine: T12
Published: 05- 2013
Rev. 00
NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the
Parts List in the appropriate place in the machine manual for future
reference. Retaining the Parts List will make it easier to reorder
individual parts and will save the cost of ordering an entire kit.
NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
Installation instructions for kit number 9009817
SYNOPSIS:
This kit contains the parts needed to replace the rear squeegee assembly on T12 scrubbers.
Please follow step-by-step instructions.
SPECIAL TOOLS / CONSIDERATIONS: NONE
(Estimated time to complete: 15 - 30 minutes)
PROTECT THE ENVIRONMENT
Please dispose of packaging materials, old machine components,
and hazardous fluids in an environmentally safe manner according
to local waste disposal regulations.
Always remember to recycle.
PREPARATION:
1. Park the machine on a clean level surface,
turn off the machine, and remove the key.
FOR SAFETY: Before leaving or servicing
machine, stop on level surface, turn off
machine, and remove key.

IB 9010947 (05- 2013)2
INSTALLATION:
1. Disconnect the vacuum hose from the rear
squeegee assembly. (Fig. 1)
FIG. 1
2. Loosen both squeegee mounting handles.
(Fig.2/Fig.3)
FIG. 2
FIG. 3
3. Pull the rear squeegee assembly from the
machine. Discard the removed squeegee
assembly. (Fig. 4)
FIG. 4
4. Install the new rear squeegee assembly onto
the machine.
5. Connect the vacuum hose to the rear
squeegee assembly.
6. Level the rear squeegee assembly and set the
rear squeegee deflection. Refer to LEVELING
THE REAR SQUEEGEE and ADJUSTING
THE REAR SQUEEGEE BLADE
DEFLECTION in the MAINTENANCE section
of the Operator Manual for instructions how to
level rear squeegee and set the rear
squeegee deflection.

IB 9010947 (05- 2013) 3
1
2
3
4
5
6
7
8
8
4
5
6
7
8
8
9
10
11
12
13
9
10
11
12
13
14
15
14
15
16
17
Note: Rear squeegee assembly is shown
disassembled to better show locations of parts. The
rear squeegee assembly is ready for installation
and Does Not need to be disassembled before
being installed onto machine.
FIG. 5

IB 9010947 (05- 2013)4
Bill Of Materials For Squeegee Kit, Rear, CI [T12] - 9009817
Ref.
Tennant
Part No. Description Qty.
o9009817 Squeegee Kit, Rear, CI [T12] 1
Y1 1200219 Frame, Sqge, Outer 1
Y2 1200218 Frame, Sqge, Inner 1
Y3 1200466 Clamp Wldt, Retainer, Sqge 1
Y4 363162 Wheel, 04.0d 0.89w 0.64b 2
Y5363301 Sleeve, P/M, 0.34b 0.63d 1.2l, Bnz 2
Y6 49694 Screw, Hex, M8 X 1.25 X 50, SS 2
Y7 08713 Nut, Hex, Lock, M8 X 1.25, Nl, SS 2
Y8 1017218 Washer, Flat, 0.32b 1.00d .12, SS 4
Y9 1052532 Grip, Lock 2
Y10 1055396 Pin, 0.63d, 02.0l [W/Cbore, M8 Screw] 2
Y11 07786 Nut, Hex, Std, M8 X 1 2
Y12 1057407 Rod, Thrd, 2end, M8x1.25/ M10x1.5 04.7l 2
Y13 1055506 Ring, Mtg, Sqge, .38l 2
Y14 1064770 Spring, Cmpr, 0.98od .13wir 01.3l, SS 2
Y15 391345 Nut, T, M10 X 1.50 X 0.62od X 0.5l 2
Y16 1200383 Blade, Sqge, Front, 42.59l [Linard] 1
Y17 1200384 Blade, Sqge, Rear, Linatex 1
TENNANT COMPANY
P. O. Box 1452
Minneapolis, MN 55440-1452