TigerTough T62213 User manual

T62213 Tactical Driver’s Seat Cover
It’s not rocket science,
but following these
instrucons will make
installing your seat covers
a lot easier.
We promise.

Your new seat covers are covered by a
two-year, unconditional, no B.S. warranty.
That means that if you manage to abuse
them to a point that they can’t perform like
they’re supposed to within two years of when
you bought them, we’ll make it right.
Depending on what is more practical, we’ll
either repair or replace the damaged cover.
Basically, you break it, we buy it.
Seriously.

INSTALLATION GUIDE
T62213 Tactical Driver’s Seat Cover
Chevrolet Tahoe SSV/PPV (2021-2022)

For assistance with installation, call us at 507.246.3545
BILL OF MATERIALS
ITEMITEM QUANTITY
Driver Seat Back Cover 1
Driver Seat Bottom Cover 1
Seat Headrest Cover 1
General care instructions:
1. In most cases dirt, debris, spills and pet hair can be removed by wiping with a
damp cloth.
2. Seat covers can be removed and machine washed on low temperature setting
using mild detergent.
Drip dry or machine tumble dry on a no heat cycle.
Straps should be coiled and secured with rubber bands for machine washing
and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should rst be treated with a dry cleaning solvent followed
by a spray cleaner or detergent and water.
5. Do not use bleach.
Ensure airbag patch (same side as the TigerTough tag) goes on the outside edge of
the seat.

For assistance with installation, call us at 507.246.3545
q 1.1 - Unhook both elastic straps from under the seat bottom to release the seat back ap.
q 1.2 - Lean seat back forward.
q 1.3 - Turn seat back cover 3/4 of the way inside out and pull over seat back.
q 1.4 - Work cover over the headrest.
q 1.5 - Continue pulling the cover down over the seat, unrolling it as you go.
q 1.6 - Tip factory seat ap up and tuck into seat cover.
q 1.7 - Push front ap between seat back and seat bottom.
q 1.8 - Pull front ap as tight as possible and fasten to Velcro on seat back.
q 1.9 - Pull ap tight under headrest and tuck into seat back cover, fastening the Velcro.
1 - Install Seat Back Cover

For assistance with installation, call us at 507.246.3545
2 - Install Seat Bottom Cover
q 2.1 - Put cover over seat bottom.
q 2.2 - Tuck cover behind plastic trim around seat. The seams in the cover will line up with seat seams.
q 2.3 - Tuck outside string between seat bottom and trim, where the back and bottom meet. Inside string goes under
seat bottom, in front of rear seat mount.
q 2.4 - Push top ap between seat back and seat bottom. Pull tight to line cover up with seat bottom.
q 2.5 - Pull strings tight. Secure using StringLock (see next page). The tighter, the better - this is what keeps your cover
from shifting.
q 2.6 - Run front aps over all seat adjustment levers, wires, and brackets.
q 2.7 - Pull front aps as tight as possible and fasten to Velcro on top ap.
q 2.8 - Fasten long ap from seat back under seat bottom.
Seat
cover
string
between
seat
bottom
and plastic
trim,
where
back and
bottom
meet.

For assistance with installation, call us at 507.246.3545
THE STRINGLOCK
Run one string through the channel on the
end of the StringLock.
Pull the string tight, pulling the StringLock
towards one edge of the seat. Press the
string into the clamp, locking it in place.
Run the second string through the
StringLock just like the other one.
Pull the loose end of the second string until
everthing is tight and lock it into place as
well.
1
3
2
4
Watch the video
ttcovers.com/stringlock

For assistance with installation, call us at 507.246.3545
3 - Install Headrest Cover
q 3.1 - Put headrest back in seat by pressing it back into place.
q 3.2 - Pull cover over head rest with “loop” Velcro in front and “hook” Velcro in rear.
q 3.3 - Fasten Velcro tabs together under headrest.
q 3.4 - Tuck cover behind plastic trim around button.