TigerTough PETERBILT 32504 User manual

INSTALLATION GUIDE
32504 PETERBILT BUCKET SEAT
PASSENGER AIR RIDE, INSIDE ARMREST

Your new seat covers are covered by a
two-year, unconditional, no B.S. warranty.
That means that if you manage to abuse
them to a point that they can’t perform like
they’re supposed to within two years of when
you bought them, we’ll make it right.
Depending on what is more practical, we’ll
either repair or replace the damaged cover.
Register your seat covers at:
ttcovers.com/RegisterMyCovers
Basically, you break it, we buy it.
Seriously.

CONTENTS IN PACKAGE
INSTALLATION INSTRUCTIONS
q 1 - Install Seat Back Cover.
q 1.1 Turn seat back cover 3/4 of the way inside out.
q 1.2 Pull cover over seat back, pulling ght against top of seat.
q 1.3 Connue pulling the cover over the seat back, unrolling it as you go.
q 1.4 Aach Velcro aps under arm rest. You may need to work the arm rest back and forth to get the seam
to meet up.
q 1.4.1 Push front ap of cover between seat back and seat boom.
q 1.4.2 Pull ap ght and fasten to Velcro on seat back.
q 2 - Install Seat Boom Cover.
q 2.1 Place seat boom cover over boom of seat.
q 2.2 Push ap on top of cover between seat back and seat boom.
q 2.3 Tip front of seat boom up.
q 2.3.1 Pull up on plasc handle in center of front of seat boom.
q 2.3.2 Pull forward.
q 2.4 Work plasc handle through square hole in seat cover.
q 2.5 Return seat boom to original posion
q 2.6 Push front ap under seat boom. Flap must go over round seat bracket.
q 2.7 Tip seat boom up.
q 2.7.1 Pull up on plac handle in center of front of seat boom.
q 2.7.2 Pull forward.
q 2.7.3 Li up on back of seat cushion.
q 2.8 Secure string behind seat with StringLock.
q 2.8.1 Pull strings ght, and secure using the StringLock device (see page 3). The ghter, the
beer. This is what keeps your cover from shiing.
q 2.9 Pull ap from front of seat cover ght and fasten to Velcro on back of seat boom.
q 2.10 Return seat boom to original posion.
q 3 - Install Armrest Cover.
q 1.1 Turn the armrest cover 1/2 way inside out and pull it over the armrest.
q 1.2 “Unroll” the armrest cover and wrap it around the back of the armrest.
q 1.3 Fasten the Velcro tabs together.
q 1.4 Repeat for the other armrest.
For Assistance Call Us At 507.246.3545
q 1 - Seat Back Cover
q 1 - Seat Boom Cover
q 1 - Armrest Cover

For Assistance Call Us At 507.246.3545
1.2- Cover inside out and on 1.3- Pull cover over seat back
2.6 - Push ap over round bar2.4- Work handle through hole2.3 - Front of boom pped up
2.2 - Push ap through to back2.1 - Put cover on seat boom1.6 - Fasten ap to back of seat1.5 - Push ap through to back
1.4 - Fasten aps under arm rest1.4 - Fasten aps under arm rest
2.10 - Put seat boom down2.9 - Fasten ap from front2.9 - Pull ap from front ght
2.8.2 - Fasten string with
String-Lock (see page above)
2.7 - Tip seat boom up
3.1 - Put armrest cover on 3.2 - “Unroll” armrest cover 3.3 - Fasten Velcro Strips

THE STRINGLOCK
Run one string through the channel on the
end of the StringLock.
Pull the string tight, pulling the StringLock
towards one edge of the seat. Press the
string into the clamp, locking it in place.
Run the second string through the
StringLock just like the other one.
Pull the loose end of the second string until
everthing is tight and lock it into place as
well.
1
3
2
4
Watch the video
ttcovers.com/stringlock