TigerTough 55560 User manual

It’s not rocket science,
but following these
instrucons will make
installing your seat covers
a lot easier.
We promise.
ttcovers.com/55560video

INSTALLATION GUIDE
55560 Rear Bench Cover
Ford Ranger (2019)

For assistance with installation, call us at 507.246.3545
BILL OF MATERIALS
ITEM QUANTITY
Seat Back Cover 1
Seat Bottom Cover 1
Armrest Cover 1
Seat Headrest Cover 3
General care instructions:
1. In most cases dirt, debris, spills and pet hair can be removed by wiping with a
damp cloth.
2. Seat covers can be removed and machine washed on low temperature setting
using mild detergent.
Drip dry or machine tumble dry on a no heat cycle.
Straps should be coiled and secured with rubber bands for machine washing
and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should rst be treated with a dry cleaning solvent followed
by a spray cleaner or detergent and water.
5. Do not use bleach.
Seat Backs & Bottoms have tag signifying Driver or Passenger.
Ensure airbag patch (same side as the TigerTough tag) goes on the outside edge of
the seat.

For assistance with installation, call us at 507.246.3545
1 - Preparation
q 1.1 - Remove all of the headrests
q 1.2 - Press button on the sides of the bigger headrests to fold them down
q 1.3 - Push the two buttons at the base of the headrests and pull up to remove

For assistance with installation, call us at 507.246.3545
2 - Install Seat Back Cover
q 2.1 - Put the seat cover behind the seat belt.
q 2.2 - Pull up on loop and tip the seat back forward
q 2.3 - Start working the cover over the seat back.
q 2.4 - Make sure the seat back loop sticks through the cover. Line up the rubber bumpers and latches with their re-
spective holes in the back of the seat.
q 2.5 - Work the cover around the plastic headrest trims
q 2.6 - Push the aps through the space between the seat back and bottom so they come out the back of the seat
q 2.7 - Fold the seat back down and connect the Velcro aps to the velcro on the back of the seat cover. The tighter you
pull the better the cover will t

For assistance with installation, call us at 507.246.3545
q 3.1 - Slide armrest cover over armrest
q 3.2 - Pull Velcro from the bottom towards the top
q 3.3 - Push the Velcro from the top towards the bottom and connect with the other Velcro ap
q 3.4 - Make sure the release loop comes out of the hole in the from of the armrest cover
3 - Install Armrest Cover

For assistance with installation, call us at 507.246.3545
4 - Install Seat Bottom Cover
q 4.1 - Flip the seat up and slide the cover over the over the seat
q 4.2 - Pull the seat latch loops through the holes on both sides of the cover
q 4.3 - Tuck cover behind the rubber feet.
q 4.4 - Fold the seat down and push the aps through the seat back and seat bottom
q 4.5 - Pull the Velcro aps and attach them to the Velcro on the bottom of the cover.

For assistance with installation, call us at 507.246.3545
5 - Install Headrest Covers
q 5.1 - Put headrest back in seat by pressing plastic tabs and pushing down on headrest.
q 5.2 - Pull cover over head rest with “loop” Velcro in front and “hook” Velcro in rear.
q 5.3 - Fasten Velcro tabs together under headrest.