TigerTough T52217 User manual

INSTALLATION GUIDE
T52217 Tactical Driver’s Bucket
FORD INTERCEPTOR UTILITY (2020)

For assistance with installation, call us at 507.246.3545
BILL OF MATERIALS
ITEMITEM QUANTITY
Driver Seat Back Cover 1
Driver Seat Bottom Cover 1
Headrest Cover 1
General care instructions:
1. In most cases dirt, debris, spills and pet hair can be removed by wiping with a
damp cloth.
2. Seat covers can be removed and machine washed on low temperature setting
using mild detergent.
Drip dry or machine tumble dry on a no heat cycle.
Straps should be coiled and secured with rubber bands for machine washing
and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should rst be treated with a dry cleaning solvent followed
by a spray cleaner or detergent and water.
5. Do not use bleach.
Seat Backs & Bottoms have tags signifying Driver or Passenger.
Ensure airbag patch (same side as the TigerTough tag) goes on the outside edge of
the seat.
Watch the installation video at ttcovers.com/t52217video

For assistance with installation, call us at 507.246.3545
Your new seat covers are covered by a
two-year, unconditional, no B.S. warranty.
That means that if you manage to abuse
them to a point that they can’t perform like
they’re supposed to within two years of when
you bought them, we’ll make it right.
Depending on what is more practical, we’ll
either repair or replace the damaged cover.
Register your seat covers at:
ttcovers.com/RegisterMyCovers
Basically, you break it, we buy it.
Seriously.

For assistance with installation, call us at 507.246.3545
Install Seat Bottom Cover
Slide the seat
forward and
raising it to the
highest position
to give you the
most amount of
working room.
Unhook the ap
behind seat that
runs under bot-
tom of the seat
1
2
3
4
Place cover over
seat bottom
Push the three
aps with velcro
on them between
the back and the
bottom of the
seat. Tuck the
sides of the cover
between the
plastic trim on the
side of the seat.
Tuck the sides of
the cover be-
tween the plastic
trim on the side
of the seat.
Drop the string
closest to the
door between the
plastic trim and
the seat cush-
ion to run it on
the inside of the
seat frame. Drop
the string on the
other side down
to the oor.
Reach around
from the back
of the seat and
secure the strings
tightly using the
StringLock device
(see next page.)
The tighter the
strings, the better
your cover will t.
Take the front
aps of the cover
and run them be-
tween the plastic
trim on the front
of the seat and
under the seat to
the back, making
sure it is above
the seat mecha-
nisms.
From behind the
seat, fasten the
aps from the
top and the aps
from the bottom
together.
5
6
7
8

For assistance with installation, call us at 507.246.3545
THE STRINGLOCK
Run one string through the channel on the
end of the StringLock.
Pull the string tight, pulling the StringLock
towards one edge of the seat. Press the
string into the clamp, locking it in place.
Run the second string through the
StringLock just like the other one.
Pull the loose end of the second string until
everthing is tight and lock it into place as
well.
1
3
2
4
Watch the video
ttcovers.com/stringlock

For assistance with installation, call us at 507.246.3545
Install Seat Back Cover
Undo the ap on top of the seat back cover.
Turn cover 3/4 inside out, work cover over
headrest and down the seat back.
Tuck the edges of the gap at the top of the seat
cover under the plastic trim of the headrest
mounts.
Fasten the velcro between the headrest
mounts.
Tuck the aps at the bottom of the seatback
between the seat back and seat bottom.
Reach behind the seat to tuck the seat ap
(that you released before putting on the bottom
cover on) up into the seat back cover.
Pull the aps that you pushed between the
back and the bottom tight, and secure them to
the velcro behind the seat. The tighter you pull
them the better the cover will t.
Pull the aps that you pushed between the
back and the bottom tight, and secure them to
the velcro behind the seat. The tighter you pull
them the better the cover will t.
Slide the headrest cover over the headrest and
fasten the velcro at the bottom.
9
10
11
12