TigerTough 182103 User manual

It’s not rocket science,
but following these
instrucons will make
installing your seat covers
a lot easier.
We promise.
182103 - Bucket Set

INSTALLATION GUIDE
182103 Bucket Set
Tesla Model Y/Model 3

For assistance with installation, call us at 507.246.3545
BILL OF MATERIALS
ITEMITEM QUANTITY
Driver Seat Back Cover 1
Driver Seat Bottom Cover 1
Passenger Seat Bottom Cover 1
Passenger Seat Back Cover 1
Headrest Cover 2
General care instructions:
1. In most cases dirt, debris, spills and pet hair can be removed by wiping with a
damp cloth.
2. Seat covers can be removed and machine washed on low temperature setting
using mild detergent.
Drip dry or machine tumble dry on a no heat cycle.
Straps should be coiled and secured with rubber bands for machine washing
and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should rst be treated with a dry cleaning solvent followed
by a spray cleaner or detergent and water.
5. Do not use bleach.
Seat Backs & Bottoms have tags signifying Driver or Passenger.
Ensure airbag patch (same side as the TigerTough tag) goes on the outside edge of
the seat.
Watch the installation video at ttcovers.com/182103

For assistance with installation, call us at 507.246.3545
Your new seat covers are covered by a
two-year, unconditional, no B.S. warranty.
That means that if you manage to abuse
them to a point that they can’t perform like
they’re supposed to within two years of when
you bought them, we’ll make it right.
Depending on what is more practical, we’ll
either repair or replace the damaged cover.
Basically, you break it, we buy it.
Seriously.

For assistance with installation, call us at 507.246.3545
Install Seat Bottom Cover
Slide the seat
forward and raising
it to the highest
position to give you
the most amount of
working room.
From behind the
seat, locate the two
plastic clips holding
the factory ap to
the seat bottom.
1
2
3
4
Unhook the
plastic clips that
hold the ap to
the seat bottom
Plasce seat
bottom cover
over seat bottom
with long ap
towards the front.
Push the short
ap between the
seat back and
bottom.
Drop the string
closest to the
door between the
plastic trim and
the seat cushion
to run it on the
inside of the seat
frame. Drop the
string on the
other side down
to the oor on the
other side.
Pull the strings
tight together
underneath of
the seat and
secure the strings
tightly using the
StringLock device
(see next page.)
The tighter the
strings, the better
your cover will t.
Take the front
aps of the cover
and run them
above the metal
bar at the front
of the seat and
under the seat to
the back. This is
better shown in
the video.
Tuck the side
of the cover in
between the seat
and the plastic
trim for a clean
look.
5
6
7
8

For assistance with installation, call us at 507.246.3545
THE STRINGLOCK
Run one string through the channel on the
end of the StringLock.
Pull the string tight, pulling the StringLock
towards one edge of the seat. Press the
string into the clamp, locking it in place.
Run the second string through the
StringLock just like the other one.
Pull the loose end of the second string until
everthing is tight and lock it into place as
well.
1
3
2
4
Watch the video
ttcovers.com/stringlock

For assistance with installation, call us at 507.246.3545
Install Seat Back Cover
Undo the ap on
top of the seat back
cover. Turn cover
3/4 inside out, work
cover over headrest
and down the seat
back.
Unroll the cover
the rest of the way
down the seat back.
Push the aps
between the seat
back and bottom.
Pull the aps
that you pushed
between the back
and the bottom
tight, and secure
them to the velcro
behind the seat.
The tighter you pull
them the better the
cover will t.
Tuck the factory
seat ap up into the
seat back cover.
9
10
11
12
13
14
15
16
Fasten the
wide ap from
the seat back
cover around to
the seat bottom
cover.
Feed the ap
between the
headrest and
seat back.
Fasten velcro.
And you’re
done!
Put headrest
cover on with the
long ap in the
front. Push this
ap between the
seat back and
bottom as well.