TigerTough 32201 User manual

It’s not rocket science,
but following these
instrucons will make
installing your seat covers
a lot easier.
We promise.
32201 Gramag
High Back Bucket Seat

Your new seat covers are covered by a
two-year, unconditional, no B.S. warranty.
That means that if you manage to abuse
them to a point that they can’t perform like
they’re supposed to within two years of when
you bought them, we’ll make it right.
Depending on what is more practical, we’ll
either repair or replace the damaged cover.
Register your seat covers at:
ttcovers.com/RegisterMyCovers
Basically, you break it, we buy it.
Seriously.

INSTALLATION GUIDE
32201 Gramag High Back Bucket Seat
Peterbilt

For assistance with installation, call us at 507.246.3545
BILL OF MATERIALS
ITEMITEM QUANTITY
Driver Seat Back Cover 1
Driver Seat Bottom Cover 1
General care instructions:
1. In most cases dirt, debris, spills and pet hair can be removed by wiping with a
damp cloth.
2. Seat covers can be removed and machine washed on low temperature setting
using mild detergent.
Drip dry or machine tumble dry on a no heat cycle.
Straps should be coiled and secured with rubber bands for machine washing
and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should rst be treated with a dry cleaning solvent followed
by a spray cleaner or detergent and water.
5. Do not use bleach.

For assistance with installation, call us at 507.246.3545
1 - Preparation
q 1.1 - Raise seat to the highest position and slide forward.
q 1.2 - Remove seat bottom.
q 1.2.1 - Using a small pick, release the driver’s side of the seat bottom by inserting a small pick near the front
of the seat and pushing up to release the reataining clip. Pull the seat bottom forward.
q 1.2.2 - Repeat on the passenger’s side of the seat bottom.
q 1.2.3 - Note - If you are doing this alone, you will need to use a small at screwdriver to keep the seat
adjustment lever from latching. When the seat is slid forward, push the screwdriver in to the last hole of
the adjustment mechanism, above the latch peg.
q 1.3 - Slide the seat bottom forward and lift o󰀨 the frame.
Seat bottom release tab on front of seat.
Two per seat bottom.

For assistance with installation, call us at 507.246.3545
2 - Install Seat Bottom Cover
q 2.1 - Place cover over seat bottom, making sure buttons on front of seat line up with the cutout in the front of the
cover.
q 2.2 - Pull strings tight, and secure using the StringLock device (see next page). The tighter, the better. This is what
keeps your cover from shifting.
q 2.3 - Pull fabric straps from front of seat across seat bottom. Pull front and rear straps as tight as possible and fasten
Velcro together. When running straps across seat bottom, ensure that the four mounting holes (circled in red
above) are not covered by the straps.
q 2.4 - Put the seat bottom back on the frame, lining the four mounting holes up with the plastic tabs on the seat frame.
q 2.5 - Press down on the seat bottom and slide back while pulling up on the seat adjustment lever. This will mount the
seat back on the frame.
q 2.6 - Press the bottom of the seat cover behing the plastic trim of the seat. You may use a at screwdriver to do this
without damaging the cover.

For assistance with installation, call us at 507.246.3545
THE STRINGLOCK
Run one string through the channel on the
end of the StringLock.
Pull the string tight, pulling the StringLock
towards one edge of the seat. Press the
string into the clamp, locking it in place.
Run the second string through the
StringLock just like the other one.
Pull the loose end of the second string until
everthing is tight and lock it into place as
well.
1
3
2
4
Watch the video
ttcovers.com/stringlock

For assistance with installation, call us at 507.246.3545
3 - Install Seat Back Cover
q 3.1 - Remove two “Christmas Tree” fasteners holding fabric ap to seat frame. Pull out of ap and stick back into seat
frame for safekeeping.
q 3.2 - Fold cover 3/4 of the way inside out and pull down tight against the headrest. The TigerTough tag should be on
the side toward the door.
q 3.3 - Pull the cover down over the seat back, unrolling it as you go. The seams in the cover should be lined up with
the seams on the seat.
q 3.4 - Tuck the seat back ap up into the seat cover.
q 3.5 - Fasten Velcro tabs together armrests.
q 3.6 - Push fabric ap from front of seat between the seat back and bottom.
q 3.7 - Pull the front ap as tight as possible and fasten to Velcro on back of cover.