TonerRefillKits ReChargX RX217 User manual

TonerRellKits.com  RechargX™RX217
Mon-Fri8am-5pmET©1995-2011ReChargX™,EmptyX,TonerRellKitsandTonerRellKits.com,theTonerRellKitslogo,the 2011.06.27
800.527.3712or352.343.7533ReChargX™andEmptyXlogosaretrademarksownedbyTonerRellkits,LLC.Allrightsreserved. Page1of8
ReChargX™ RX217 Instructions
For use in the Samsung SCX-4725F toner cartridge
ThisisthetonercartridgeusedintheSamsung
SCX-4725Fandothermachinesusingthesame
underlyingengine.
These cartridges are quite easy to rell using
our ReChargX™ RX217 Premium Print Toner
RellKit.
Thiscartridgeisunusualindesign(gure1)with
averylong“handle”usedtoinstallthecartridge
intotheprinter.
Step 1: Locate the Imaging Drum
Theimagingdrumcanbefoundontheunderside
ofthetonercartridge,simplyipthecartridge
over so that the blue/green imaging drum
(shownbythearrowsingure2)isfacingup
andthebaseofthehandleistowardyourbody.
Step 2: Cover the Imaging Drum
The imaging drum is completely exposed and
easytodamagebyscratchingorcontaminating
withngerprints.
Beforewestartworkingwiththecartridgewe
willuseapieceofpapertoprotecttheimaging
drumwhichrunsalongthecartridgefront.
Takeasheetofpaperandtapeittothebottom
ofthecartridge(asshowningure3),thenfold
thepaperdownandovertheimagingdrumon
theleadingedgeofthecartridge.
Figure 1:SamsungSCX-4725Ftonercartridge
è
è
Figure 2: Locatetheimagingdrum
Figure 3:Tapeapieceofpapertothebottomofthe 
 tonercartridge

TonerRellKits.com  RechargX™RX217
Mon-Fri8am-5pmET©1995-2011ReChargX™,EmptyX,TonerRellKitsandTonerRellKits.com,theTonerRellKitslogo,the 2011.06.27
800.527.3712or352.343.7533ReChargX™andEmptyXlogosaretrademarksownedbyTonerRellkits,LLC.Allrightsreserved. Page2of8
Tocompletetheprotectionofthedrum,turnthe
cartridgeoverandtapethepieceofpapertothe
topofthecartridge,aswell(gure4).
(Thisstepisnecessarysincethedrumcanbe
scratchedorngerprintscanleaveweakspots
ontheimagingdrum,affectingitsabilitytopick
uptoner.)
Step 3: Locate the Cartridge End Cap
Next,standthecartridgeupsotherighthand
sideofthecartridgeisfacingup(gure5).
Step 4: Remove the Screws Holding the
End Cap in Place
Wewillremovethescrews(highlightedbythe
arrowsingure6)sowecanremovetheend
capfromthecartridge.
Figure 4: Tapethepieceofpapertothetopofthetoner
 cartridge.
Figure 5: Rightsidefacingup
è
è
Figure 6:Removethesescrews

TonerRellKits.com  RechargX™RX217
Mon-Fri8am-5pmET©1995-2011ReChargX™,EmptyX,TonerRellKitsandTonerRellKits.com,theTonerRellKitslogo,the 2011.06.27
800.527.3712or352.343.7533ReChargX™andEmptyXlogosaretrademarksownedbyTonerRellkits,LLC.Allrightsreserved. Page3of8
Step 5: Remove the End Cap
To remove the end cap most easily, lay the
cartridgeupsidedownonthetable(sothetop
ofthecartridgeisonthetabletop).
Next,useasmallatbladescrewdrivertogently
prytheendcapawayfromthebodyofthetoner
cartridge(gure7).
Step 6: Remove the End Cap Completely
Whentheendcaphasbeenwedgedawayfrom
the body of the cartridge, wiggle the end cap
whilepullingitoffofthecartridgetoremoveit
completely(gure8).
Step 7: Locate the Toner Hopper Plug
Withtherighthandsideofthecartridgefacing
up, the toner hopper plug can be found just
underthehingeofthehandleasshownbythe
arrowingure9.
Figure 7: Gentlyprytheendcapawayfromthebodyof
 thetonercartridge
Figure 8: Pulltheendcapcompletelyoffthebodyof 
 thetonercartridge
ç
Figure 9:Locatethetonerhopperplug

TonerRellKits.com  RechargX™RX217
Mon-Fri8am-5pmET©1995-2011ReChargX™,EmptyX,TonerRellKitsandTonerRellKits.com,theTonerRellKitslogo,the 2011.06.27
800.527.3712or352.343.7533ReChargX™andEmptyXlogosaretrademarksownedbyTonerRellkits,LLC.Allrightsreserved. Page4of8
Step 8: Remove the Toner Hopper Plug
Werecommendusingthetipofasmallat-blade
screwdrivertowedgeupandundertheplug.
Keep working your way around the lip of the
plug,wedginguponit,slowlymovingtheplug
upandoutofthehole(gure10).
We normally move around the plug until we
haveitalmostallofthewayupandoutofthe
hole,theneitherusethescrewdriveragainstthe
plasticrimofthehole,usingitasafulcrumto
wedgetheplugupandoutuntilitisfreedfrom
thehole,grabitwithapairofpliers,orifloose
enough,itcanbepulledoutwithyourngers.
Step 9: Add ReChargX™ RX217 Premium
Print Toner to the Toner Hopper
Now we will ll the toner hopper with the
ReChargX™RX217PremiumPrinttoner .
Toensurethetonerowsfreelyfromthebottle
duringlling,makecertainthecapisscrewed
tightlyonthebottle,thengentlyrock/shakethe
bottletofreeupthetonerthatmayhavesettled
duringshipping.
Next,removetheoriginalcapfromthebottleand
replaceitwiththeplasticdispenserspoutfrom
theReChargXRX217TonerRellKit.
To make the adding of the toner to the toner
hopperaseasyanddust-freeaspossible,tiltthe
endofthecartridgewiththeholeinitupata
45degreeangleandslowlyanglethedispenser
spoutonthebottleoftonertomeetupwiththe
hole,asshowningure11.Tiltingthebottle
upalittlemorewillstartthetonerowinginto
thetonerhopper.
NOTE:Ifatanypointthetonerstopsowing,
simply stand the bottle upright to loosen the
tonerandstartthepouringprocessoveragain
(resisttemptationtosqueezethebottleasitwill
makeaspillormessmorelikely).
Fillthehopperuntilitappearstobefulloruntil
itappearstonernolongerowseasilyintothe
hopper(anytonerleftinthebottlecaneasily
beaddedinthe future after youhavedonea
considerableamountofprinting).
Figure 10: Useaatbladescrewdrivertoremovethe
tonerhopperplug
Figure 11:Fillthetonerhopper

TonerRellKits.com  RechargX™RX217
Mon-Fri8am-5pmET©1995-2011ReChargX™,EmptyX,TonerRellKitsandTonerRellKits.com,theTonerRellKitslogo,the 2011.06.27
800.527.3712or352.343.7533ReChargX™andEmptyXlogosaretrademarksownedbyTonerRellkits,LLC.Allrightsreserved. Page5of8
Step 10: Install the New Toner Hopper Plug
WhenyouhavenishedpouringtheReChargX™
toner into the hopper, insert the replacement
plug,foundinyourReChargX™RX217RellKit,
intotheholeandpushitdownrmlyuntilitsnaps
intoplaceandsitsushagainstthesideofthe
tonerhopper(gure12).
Once you have completed this step, place
cartridgeaside
In the Following steps you will be working
on the cartridge end cap rather than the
cartridge itself.
Step 11: Locate the Old Reset Chip
TheSamsungSCX-4725Fhasaresetchiplocated
onitsendcap,asshownbythecircleingure13,
whichneedstobereplacedbeforethemachine
willrecognizethecartridgeasbeing“new”.
Turningtheendcapoveryouwillnoticeaplastic
coveroverthechipheldinplacebytwosnap-in
plasticprongs,asshownbythewhitearrowsin
gure14.
Figure 12:Installthenewtonerhopperplug
Figure 13: Locatetheoldresetchip
ç
ç
Figure 14:Theresetchipisheldinplacebytwo 
plasticprongs

TonerRellKits.com  RechargX™RX217
Mon-Fri8am-5pmET©1995-2011ReChargX™,EmptyX,TonerRellKitsandTonerRellKits.com,theTonerRellKitslogo,the 2011.06.27
800.527.3712or352.343.7533ReChargX™andEmptyXlogosaretrademarksownedbyTonerRellkits,LLC.Allrightsreserved. Page6of8
Step 12: Remove the Plastic Cover
Toexposetheresetchipwewillpryupon
eachplasticprongtodisengageitfromthe
postitissnappedinunder.
Weuseasmallat-bladescrewdriver(oryou
could use the tip of a small knife) wedged
undertheprongandthentwistthebladeto
pop the prong up and out from under the
catch(gure15).
Step 13: Remove the Old Reset Chip
Usingaatbladescrewdriver,gentlypryupon
theresetchipusingthesideoftheendcapas
afulcrum(gure16).
Step 14: Install the New Reset Chip
Toinsertthenewchip,makesurethemetal
contacts are located on the right of the
undersideofthe replacementresetchip,
slideitundertheplasticange(markedby
thearrowingure17),thenitispressed
rmlyinplaceintotheendcap.
(Note: Thereset chipshouldtsnugglyinto
theendcap.)
Figure 15:Removetheplasticcover
Figure 16:Removetheoldresetchip
ç
Figure 17:Installthenewresetchip

TonerRellKits.com  RechargX™RX217
Mon-Fri8am-5pmET©1995-2011ReChargX™,EmptyX,TonerRellKitsandTonerRellKits.com,theTonerRellKitslogo,the 2011.06.27
800.527.3712or352.343.7533ReChargX™andEmptyXlogosaretrademarksownedbyTonerRellkits,LLC.Allrightsreserved. Page7of8
Step 15: Reinstall the Plastic Cover
Slidethecoverinatanangleunderthesame
plasticangeontheleftandthenwilllowerit
downontherightsotheholeinittsoverthe
plasticpost(gure18).
Withthepostalignedinthehole,pressdownon
theplasticcoveruntilitsnapsintoplace.
Step 16: Reinstall the End Cap
Standthecartridgeupagainsothattheright
sideisfacingup(gure19)andreinstalltheend
capontothesideofthecartridge.
Youshouldseethebrasscontactsonthereset
chipthroughtheholeintheendcap.
Wiggletheendcapdownintoplace,making
certain it sits ush against the side of the
cartridgebeforereinstallingthescrewsinthe
nextstep.Reinstallthetwosmallphilips-head
screwsinto theholes markedbythearrows
(gure20).
ç
Figure 18:Reinstalltheplasticcover
Figure 19: Standthecartridgeupagainsothatthe 
 rightsideisfacingup
è
è
Figure 20:Reinstallthescrews

TonerRellKits.com  RechargX™RX217
Mon-Fri8am-5pmET©1995-2011ReChargX™,EmptyX,TonerRellKitsandTonerRellKits.com,theTonerRellKitslogo,the 2011.06.27
800.527.3712or352.343.7533ReChargX™andEmptyXlogosaretrademarksownedbyTonerRellkits,LLC.Allrightsreserved. Page8of8
Completion
Congratulations!Youhavesuccessfullyrelled
yourSamsungSCX-4725Ftonercartridgeand
replacedtheresetchip.
Enjoyyoursavings.
-EndofReChargX™RX217Instructions-
Technical Support
Tofurtherhelp yourReChargX™RX217Toner
Rell procedure, we are always ready, willing
andhappytoansweranyofyourquestionsor
commentsviatechnicalsupport.
Please contact us at 352.343.7533 or
800.527.3712M-F8am-5pmET.
Additionally, you may also chat with us using
LiveHelponourwebsite(M-F8am-5pmET)or
submitatechnicalsupportticketat 
www.TonerRellKits.com/Tech_Support.php