TOORX WLX80 User manual

Ed : 02/17
INSTRUCTION
Rev : 0000

PART LIST
NUMBER NAME COUNT
1 LEFT BASE FRAME 1
2 RIGHT BASE FRAME 1
3 CONNECTING BASE FRAME 1
4 UPRIGHT FRAME 2
5 UPPER CONNECTING ROD 1
6 LEFT BEARING TUBE 1
7 RIGHT BEARING TUBE 1
8 LEFT HOOK 1
9 RIGHT HOOK 1
1 PLATE PIN 2
11 SQUARE END PLUG 2
12 PLASTIC PLATE(LONG) 2
13 PLASTIC PLATE(SHORT) 2
14 PLASTIC PLATE 2
15 RUBBER(LONG) 2
16 RUBBER(SHORT) 2
17 M1 X9 HEX BOLT 4
18 M1 X85 HEX BOLT 4
19 M1 X8 HEX BOLT 8
2 M1 X25 HEX BOLT 4
21 M6X1 BOLT 14
22 M1 ARC WASHER 8
23 M1 WASHER 32
24 M1 LOCKNUT 12

PART DRAW

(1)LEFT BASE FRAME (2)RIGHT BASE FRAME (3)CONNECTING BASE FRAME (4)UPRIGHT FRAME
(5)UPPER CONNECTING ROD (6)LEFT BEARING TUBE (7)RIGHT BEARING TUBE (8)LEFT HOOK
(9)RIGHT HOOK (1 )PLATE PIN (11)SQUARE END PLUG (12)PLASTIC PLATE (LONG)
(13)PLASTIC PLATE (SHORT) (14)PLASTIC PLATE (15)RUBBER(LONG) (16)RUBBER(SHORT)
(23)M1 WASHER (24)M1 LOCKNUT
(19)M1 X8 HEX BOLT (2 )M1 X25 HEX BOLT(18)M1 X85 HEX BOLT
(21)M6X1 BOLT
(17)M1 X9 HEX BOLT
(22)M1 ARC WASHER
EXPLODED DRAW

5
1
2
3
4
6
7
8
9
1
1
11
11
12
12
13
13
14
14
15
16
15
17
18
18
17
19
19
19
19
2
2
21
21
21
21
21
21
21
23
24
23
24
24
24
23
23
23 23
24
23
22
21
21
22
23
27
16
22
23
23
23
STEP 1

A. ATTACH THE LEFT BASE FRAME ( 1 ) TO THE CONNECTING BASE
FRAME ( 3 ) USING 2PCS M1 X9 HEX BOLT (17) ,2PCS M1 WASHER
( 23) AND 2PCS M1 ARC WASHER (22) AS SHOWN.
B. USING 2PCS M1 X25 HEX BOLT (2 ) , 2PCS M1 WASHER ( 23) AND
2PCS M1 ARC WASHER (22) FROM THE TOP TO FIX THE POSITION
C. ATTACH THE RIGHT BASE FRAME ( 2 ) TO THE CONNECTING BASE
FRAME ( 3 ) IN THE SAME WAY
1
2
3
17
17 23
23
23
22
22
2
22 23
23
23
22
22
2
23
22
23 22
22
STEP 2
A. INSERT UPRIGHT FRAME (4 ) INTO THE BRACKET OF THE LEFT
BASE FRAME ( 1 ) BY USING 2PCS M1 X8 HEX BOLT (19 ) , 4PCS

M1 WASHER (23 ) AND 2PCS M1 LOCKNUT ( 24 ) . REPEAT THE
RIGHT SIDE AS THIS WAY
B. THEN USING 2PCS M1 X85 HEX BOLT (18 ) , 4PCS M1 WASHER
(23 ) AND 2PCS M1 LOCKNUT ( 24 ) TO TIGH THEM FROM CROSS
SIDE AS DRAWING SHOW. REPEAT IT IN RIGHT SIDE .
C. ATTACH UPPER CONNECTING ROD ( 5 ) TO THE UPRIGHT FRAME (4)
USING 4PCS M1 X8 HEX BOLT (19 ) , 8PCS M1 WASHER (23 ) AND
4PCS M1 LOCKNUT ( 24) .
24
23
23
23
24
5
23
24
23
23
23
23
24
19
19
19
18
23
18
19
23
23
24
23
24
23
23
23
23
24
23
23
23
4
4
STEP 3

A. INSERT LEFT HOOK (8) INTO ONE OF THE HOLE FROM THE
UPRIGHT FRAME (4) , REAT IT AS FOR RIGHT HOOK ( 9 )
B. INSERT LEFT BEARING TUBE (6 ) INTO ONE OF THE HOLE FROM
THE UPRIGHT FRAME (4) AND USE 1PCS PLATE PIN (1 ) TO FIX IT
FROM THE LOWER HOLE AS SHOW IN THE PICTURE . REAT IT AS
FOR RIGHT BEARING TUBE ( 7)
1
8
9
6
7
1
4
4

GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
www.toorx.it - [e-mail]