TOORX ERX900 User manual

Ed : Rev : Cod:
INSTRUCTION
02/22 GRLDTOORXERX900L01

Main frame
Console supporting
tube
E1 Handle bar (L)
E2 Handle bar (R)
ABFront stabilizer
Rear stabilizer
C
D
E
Central supporting tubeF
Console (G1)
&Console cover (G2)
G
Adaptor
I
Console supporting
tube cover (L&R)
L(A8) R(A9)
Pedal supporting tube
cover (L1&L2),(R1&R2)
L1(A72) L2(A73)
R1(A75)
R2(A74)
Front pedal supporting
tube cover
(A66)
(A67)
2

00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
(F4) Screw M8
(F2) Screw M8x65 (A107) Bolt Ø15x50.5
TOOL
M6x2
(F3) Washer M8
(A78) Screw M3x20
(A62) Spring washer M8
(A61) Washer M8
(A63) Screw M8x20
3

USE TOOL:6m/m
FRONT STABILIZER (B) ASSEMBLY
YLBMESSA)D(EBUTGNITROPPUSELOSNOC
Step 1. Remove the three preassembled screws (D2) from the console supporting tube (D).
Step 2. Connect console wire (K1&K2).
Step 4. Use two hands to hold small handle bar to lift up the main frame (A). then finish the
screw (D2-middle) assembly.
Step 5. Remove the bottom polyfoam pieces #5 & #6.
Step 1. Remove the four preassembled screws (B3), spring washer (B4)
and washer (B5) from the front stabilizer (B).
Step 2. Attach the front stabilizer (B) on to main frame (A) with screws (B3),
spring washer (B4) and washer (B5).
Step 3. Attach the console supporting tube (D) on to main frame (A) with screw (D2-left)
and screw (D2-right).
4
B
B3 B4
B5A
(D2-left) (D2-right)
(D2-middle)
K2
K1
A
D
(Hold here)
USE TOOL:6m/m
POLYFOAM(5&6)
( Main frame lift up then screw it)

F
A
F4
F4
USE TOOL:6m/m
USE TOOL:6m/m
A
FC
F2
F3
CENTRAL SUPPORTING TUBE (F) ASSEMBLY
REAR STABILIZER (C) ASSEMBLY
Step 1. Attach the central supporting tube (F)
onto main frame (A) with four screws
(F4).
Tighten the screws (F4) on the
central supporting tube when the unit is lifted.
Step 1. Attach the rear stabilizer (C ) onto the central supporting tube (F) with four
screws (F2) and washer (F3).
Step 2. Adjust the stabilizer feet on the bottom rear stabilizer (C ) to level the machine.
5
A
F
F4
F4

G3
G2
G
D
USE TOOL:
USE TOOL:
A78
A8
A9
CONSOLE & CONSOLE COVER ASSEMBLY
Step 1. Remove four screws (G3) from the console (G).
Step 2. Connect all wires.
Step 3. Fit the console (G) to console supporting tube (D).
CONSOLE SUPPORTING TUBE COVER (L&R) ASSEMBLY
Step 4.
Step 5.
Slide the console cover (G2) on console supporting tube (D).
Screw console, console supporting tube (D)
and console cover (G2) together using screws (G3).
Step 1. Attach the console supporting tube cover-L (A8) and console supporting tube cover-R
(A9) using screws (A78).
6

PEDAL TUBE COVER-(L&R) ASSEMBLY
FRONT CONNECTING SHAFT (A53) &
FRONT PEDAL SUPPORTING TUBE-L&R (A64&A65) ASSEMBLY
Step 1. Fit the pedal tube cover-L1 (A72) and pedal tube cover-L2 (A73) to the
front pedal supporting tube-L (A64) using the two screws (A78).
** Repeat same step to finish right side assembly.
7
A53
A64
A65
A62
A61
USE TOOL:6m/m
A107
A63
Step 1. Attach front connecting shaft (A53) and front pedal supporting
tube-L (A64) using bolt (A107), screw (A63) spring washer (A62)
and washer (A61).
** Repeat same step to finish right side assembly.
USE TOOL:6m/m
L1(A72)
A64
L2(A73)
A78
R2(A74)
R1(A75)

E4
E5
USE TOOL:
I
E1 E2
E5
E4
A66 A67
A108
A108
A
HANDLE BAR & FRONT PEDAL SUPPORTING TUBE COVER
ASSEMBLY
Step 1. Remove the six preassembled screws (E4&E5) from the handle bar (E1).
Step 2. Remove the two preassembled screws (A108) from the main frame (A).
ADAPTER ASSEMBLY
**Repeat same step to finish right side assembly.
Attach one end of the adapter into the
power socket and the other end into the input
jack on the main frame like shown.
Step 3. Mount the handle bar (E1) onto the
main frame (A) with screws (E4&E5).
Step 4. Mount the front pedal supporting
tube cover (A66&A67) onto the
main frame (A) with two screws (A108).
8

WARNING: Never attempt to lift the machine by yourself, ask for additional help if needed
and never attempt to lift the machine if you have any medical issues.
HOW TO TRANSPORT THE MACHINE
HOW TO USE TOGGLE SWITCH TO ADJUST THE RESISTANCE
If the machine needs to be transported to a different location, lift up the rear stabilizer
until the front transportation wheels engage the ground. You may now move the
machine to the desired location. After the move, gently set the machine down at its
new location and adjust the levelers on the bottom rear stabilizer to level the machine
if needed.
When the console is powered on, you may press the toggle buttons on the small handlebar
to adjust the resistance: Press “+LOAD” button on the right side to increase resistance and
press “-LOAD” button on the left side to decrease resistance.
9

22”
17”
Orange sticker
White sticker
Knob
HOW TO ADJUST THE STRIDE
**Please loosen the knob
first, then pull out and hold
the pedal at the same time
by moving pedal up/down
to adjust the desired stride
length.
Step 1. There are 2 different stride choices on the 1280ef. They are 17” and 22”.
(When you choose 17”, you will see the orange sticker on front pedal supporting tube,
when you choices 22”, you will see the white sticker on front pedal supporting tube.)
Step 2. Loosen the knob and pull out to adjust the stride length as you desire.
Step 3. After selecting the stride length, screw the knob back in tightly.
Step 4. Repeat this to adjust the stride length for the other side.
WARNING: NEVER adjust the stride length while standing on the machine.
Always adjust both the right and left stride to the same setting. Uneven
positions is never recommended and dangerous.
10