TOORX WBX300 User manual

Ed : 02/17
INSTRUCTION
Rev : 0000

PART LIST
NUMBER NAME COUNT
1 FRONT BASE FRAME 1
2 CONNECTOR PLATE(BIG) 2
3 CONNECTING BASE FRAME 1
4 BACK BASE FRAME 1
5 BACK UPRIGHT FRAME 1
6 FRONT UPRIGHT FRAME 1
7 AD USTABLE FRAME 1
8 CONNECTING FRAME 1
9 SLIDING ROD 1
10 CANTILEVER 1
11 CONNECTOR PLATE(SMALL) 2
12 SLIDE AD USTABLE FRAME 1
13 FOAM AD USTABLE FRAME 1
14 BAFFLE AD USTABLE FRAME 1
15 BAFFLE 1
16
17
NONE
RUNNING BOARD
0
1
18 ANCON CUSHION 2
19 FOAM 4
20 FOAM BAG 4
21 50x75 SQUARE END PLUG 7
22 25x50 SQUARE END PLUG 4
23 OIL BUSHING 2
24 60X50 SQUAER BUSHING 6
25 50 SQUARE END PLUG 1
26 ROUND END PLUG 2
27 FOAM COVER 4
28 HAND GRIP 2
29 HANDING WHEEL 2
30 POPPIN 3
31 PRESS LOCK KNOB 1
32 RUBBER BUSHING 2
33 RUBBER MAT 7
34 M10X65 CARRIAGE BOLT 2
35 M10X95 HEX BOLT 12
36 M10X85 HEX BOLT 4

37 M10X80 HEX BOLT 1
38 M10X75 HEX BOLT 4
39 M8X45 HEX BOLT 2
40 M10X20 HEX BOLT 2
41 M10X16 HEX BOLT 6
42 M10 WASHER 48
43 M10 LOCKNUT 21
44 M8 WASHER 4
45 M8 LOCKNUT 2
PART DRAW

(1)FRONT BASE
FRAME
(2)CONNECTOR
PLATE(BIG)
(3)CONNECTING
BASE FRAME
(4)BACK BASE
FRAME
(5)BACK UPRIGHT
FRAME
(6)FRONT
UPRIGHT FRAME
(7)ADUSTABLE
FRAME
(8)CONNECTING
FRAME
(9)SLIDING ROD (10)CANTILEVER
(11)CONNECTOR
PLATE(SMALL)
(12)SLIDE
ADUSTABLE
FRAME
(13)FOAM
ADUSTABLE
FRAME
(14)BAFFLE
ADUSTABLE
FRAME
(15)BAFFLE
(17)RUNNING
BOARD
(18)ANCON
CUSHION
(19)FOAM (21)50X75
SQUARE
END PLUG
(31)PRESS LOCK
KNOB
(26)ROUND
END PLUG
(27)FOAM COVER
(32)RUBBER BUSHING
(23)OIL BUSHING
(28)HAND GRIP
(25)50 SQUARE
END PLUG
(30)PIN(29)HANDING WHEEL
(22)25X50
SQUARE
END PLUG
(24)60X50
SQUAER
BUSHING
(34)M10X65
CARRIAGE BOLT
(20)FOAM BAG
(33)RUBBER MAT
(42)M10 WASHER (43)M10 LOCKNUT
(40)M10X20 HEX BOLT
(35)M10X95 HEX BOLT
(38)M10X75 HEX BOLT (39)M8X45 HEX BOLT (41)M10X16 HEX BOLT
(37)M10X80 HEX BOLT(36)M10X85 HEX BOLT
(44)M8 WASHER (45)M8 LOCKNUT
EXPLODED DRAW

1
3
4
5
6
7
8
9
10
12
13
14
17
18
19
19
19
21
21
21
21
21
21
21
22
22
22
22
23
23
24
24
24
24
24
25
28
28
26
26
30
30
30
31
43
32
32
27
27
33
33
33
33
24
19
27
27
33
242
42
35
42
43
43
42
42
43
43
42
33
2
35
42
39
39
42
44
29 44
45
44
44
45
29
33
34
34
41
42
42 42
42
41
41
41
42
42
41
36
38
42
43
42
35
11
42
42
35
42
42
43
43
11
42
43
36
41 42
38
42
42
37
40
15
42
42
42 43
43
42
43
43 42
42
42
38
38

STEP 1
A. ATTACH CONNETCTING BASE FRAME (3) TO FRONT BASE FRAME (1) WITH
CONNECTOR PLATE (BIG)(2) USING TWO PCS M10X65 CARRIAGE BOLT (35) , 4PCS
M10 WASHER (42) AND 2PCS M10 LOCKNUT (43) AS SHOWN
B. ATTACH BACK BASE FRAME (4) TO CONNETCTING BASE FRAME (3) WITH
CONNECTOR PLATE (BIG)(2) USING TWO PCS M10X65 CARRIAGE BOLT (35) , 4PCS
M10 WASHER (42) AND 2PCS M10 LOCKNUT (43) AS SHOWN
C. ASSEMBLE HANDLING WHEEL ( 29 ) INTO THE BRACKET OF BACK BASE FRAME (4)
BY USING 2PCS M8X45 HEX BOLT ( 39) , 4PCS M8 WASHER ( 44) AND 2PCS M8
LOCKNUT (45)
2
2
1
42
43
43
42
3
42
42
35
35
42
4
39
39
42
42
43
43
42
44
29 44
45
44
44
45
29

STEP 2
A. ATTACH BACK UPRIGHT FRAME (5) TO AD USTABLE FRAME ( 7) USING 1PCS M10X75
HEX BOLT (38) , 2 PCS M10 WASER ( 42) AND 1PCS M10 LOCKNUT (43). INSERT
SLIDING ROD (9) THROUGH THE HOLE OF BACK UPRIGHT FRAME (5) USING 1PCS
M10X16 HEX BOLT (41) , 1 PCS M10 WASER ( 42) AS SHOW . ATTACH CONNECTING
FRAME ( 8) TO BACK UPRIGHT FRAME (5) USING 2PCS M10X85 HEX BOLT (36) , 2
PCS M10 WASER ( 42) AS SHOW
B. SLIDE AD USTABLE FRAME (12) THROUGH AD USTABLE FRAME ( 7) AND SLIDING
ROD (9) THE SAME TIME , SCREW ON THE POPPIN (30) AND PRESS LOCK KNOB (31)
C. ATTACH FRONT UPRIGHT FRAME ( 6) TO THE PARTS OF AD USTABLE FRAME ( 7),
CONNECTING FRAME ( 8) AND SLIDING ROD (9) USING 1PCS M10X75 HEX BOLT (38) ,
2PCS M10X85 HEX BOLT (36), 1PCS M10X16 HEX BOLT (41) , 5 PCS M10 WASER ( 42)
AND 1PCS M10 LOCKNUT (43)
5
42
43
38
36
41
12
30
31
7
9
8
6
42
42
42
43
41
36
42
42
38
42
42

STEP3
A. ATTACH THE WHOLE PART FROM STEP 2 (5, 6..) INTO THE BRACEKT OF BASE
FRAME (1, 4) USING 4PCS M10X95 HEX BOLT (35) , 8 PCS M10 WASER ( 42) AND
4PCS M10 LOCKNUT (43)
B. ASSEMBLE RUNNING BOARD ( 17) ONTO THE AD USTABLE FRAME (8) USING 2PCS
M10X75 HEX BOLT (38) , 4PCS M10 WASER ( 42) AND 2PCS M10 LOCKNUT (43) AS
SHOW
35 42
42
43
43
42
42 35
42
43
8
6
5
3
2
2
1
4
17
43 42
42
42
38
38

STEP4
A. SLIDE BAFFLE AD USTABLE FRAME (14) AND THEN FOAM AD USTABLE FRAME (13)
ONTO SLIDE AD USTABLE FRAME (12). SCREW POPPIN ( 30) TO ITS POSITION ON
BAFFLE AD USTABLE FRAME (14) AND FOAM AD USTABLE FRAME (13). SLIDE 4PCS
FOAM (19) ONTO THE ROUND TUBING AND THEN ATTACH FOAM COVER (27) AT
THEIR END.
THEN TO FIX THE STOP POSITION USING 1PCS M10X80 HEX BOLT (37) , 2PCS
RUBBER BUSHING ( 32) AND 1PCS M10 LOCKNUT (43) AS SHOW
B. ATTACH BAFFLE (15) TO BAFFLE AD USTABLE FRAME (14) USING 2PCS M10X20 HEX
BOLT (40) , 4PCS M10 WASER ( 42) AND 2PCS M10 LOCKNUT (43) AS SHOW
C. ATTACH CANTILEVER (10) TO FRONT UPRIGHT FRAME (6) 2PCS M10X65 CARRIAGE
BOLT (34) , 2PCS M10 WASER ( 42) AND 2PCS M10 LOCKNUT (43) AS SHOW
D. TO FIX THE PARTS OF CANTILEVER (10) AND FRONT UPRIGHT FRAME (6) BY USING
2PCS CONNECTOR PLATE(SMALL) (11) , 4PCS M10X95 HEX BOLT (35) , 8PCS M10
WASER ( 42) AND 4PCS M10 LOCKNUT (43) AS SHOW
E. ASSEMBLE ANCON CUSHION (18) TO CANTILEVER (10) USING 4PCS M10X16 HEX
BOLT (41) AND 4PCS M10 WASER ( 42)

35
11
10
34
34
18
14
19
19
19
19
43
37
32
32
30
30
13
40
15
41
42
43
27
27
27
42
43
6
42
42
42
42
42
42
41
41
41
35
42
42
43
43
11
27
42
42
42 43
43
12