TOORX MSX 60 User manual

Ed : 02/17
INSTRUCTION
Rev: 0000

11
Contents
2
3-5
6-7
8-24
25
26-28
Safety Information
Components - Parts
Components – Fixings
Assembly Instructions
esistance chart
Home Gym Exercise Guide
Home Gym Exercise Guide
Exercising Information 29-32
Before starting to exercise 29
Muscle chart 30
Warming up and cooling down
Exercises
31-32
Care and Maintenance 33
Free area and training area 34
Exploded Parts List 35-38
Guarantee 38
1

MUST read all instructions before using any fitness equipment. Argos assumes no responsibility for
personal injury or property damage sustained by or through the use of this product.
Note: Some of the smaller components may be pre-fitted to larger components. lease check carefully
before contacting Argos regarding any missing components.
Components - arts
lease check you have all parts listed below
3

Note: Some of the smaller components may be pre-fitted to larger components. lease check carefully
before contacting us regarding any missing components.
Components - arts
lease check you have all parts listed below
4

Components - arts
lease check you have all parts listed below
5

Note: Some of the smaller components may be pre-fitted to the larger components. lease check carefully
before contacting us regarding any missing components. lease prepare an adjustable spanner by
yourself when you are intend to assemble this machine.
Components - Fixings
lease check you have all fixings listed below
6

7
Components - Fixings
lease check you have all fixings listed below

Assembly instructions
(A) Insert the 2pcs guide rods (20)
into the holes of the rear
stabilizer (2) separately . and
Secure them with 2 pcs Ø10mm
Washers (67) and 2 pcs M10 x
25mm Allen Bolts (58) . Slide the
2pcs rubber bumpers (101) along
the 2 pcs guide rods from the top
to the bottom.
(B) Attach the main base frame (8) to
the rear stabilizer(2), Secure them
with 2pcs M10×70 carriage
bolts(64), one pc bracket(26),
2pcs Ø10 washers(67) and 2 pcs
M10 Aircraft nuts(69).
(C) Attach the front stabilizer(10) to
the main base frame(8), Secure
them with one pc bracket(25),
2pcs M10×70 carriage bolts(64),
2pcsØ10 washers(67) and 2 pcs
M10 aircraft nuts(69).
(D) Attach the foot palte (27) to the
front stabilizer(10), Fix them with
one pc foot plate tube(28), two
pcs M10*25 Allen bolt(58),
2pcsØ10 washer(67)
.
Step 1
8

Attach the front vertical frame (3) onto the main base frame(8) , carefully align the holes and secure them
with 2 pcs M10×70 carriage bolts(64), one pc bracket (25),2pcs 2pcs Ø10 washers (67) and 2 pcs M10
Aircraft nuts (69).
Assembly instructions
9
Step 2

10
Assembly instructions
(A)Slide the 14pcs weight plate(37) along the guide rods (20) from the top to the bottom.insert the
selector rod (13) into the hole of weight plates. and then place the last weight plate onto the selector
rod (19)
Make sure that all the grooves face front and backwards.
(B) Insert the selector pin (38) into the hole and select the desired weight when exercising.
.
Step 3
Make sure that all the grooves
face front and backwards.

lace the upper frame (4) onto the front vertical frame (3) and 2 pcs guide rods, Carefully align the holes
and secure them with 2pcs M10*25 Allen bolt (58), 2pcs Ø10 washers (67). 2pcs M10*90 Crriage
bolts(63), one pc bracket(25), 2pcsØ10 washers (67) and 2pcs M10 aircraft nuts(69).
Assembly instructions
Step 4
11

(A). Attach the front press base (11) to the upper frame (4), Secure them with one pc Ø16*M10*206
axle(41), 2pcs Ø10 washers (67) and 2pcs M10 aircraft nuts (69).
(B) Attach the upper right butterfly frame(6) through the hole of the front press base(11) as the diagram
shows and secure them with M18 Lock ring(76), 1 pc Ø10 washer (67), 1pc M10 X16 Allen bolt
(59).Insert the lower right butterfly frame(29) into the opening of upper right butterfly frame(6) and adjust
it with one pc Lock knob (39) and one pc M10*18 Allen bolt (62). ush one pc foam roll(51) from the
bottom of the lower right butterfly frame and then secure the butterfly handle (15) with 1 pc Ø10 washer
(67), 1pc M10 X25 Allen bolt (58). Install the total left butterfly frame with the same way.
(C) Fix the swivel pulley bracket support (9) with one pc M10*110 Allen bolt (54), 2pcs Ø 10 washers(67)
and one pc M10 aircraft nut (69).Install the right and left swivel pulley bracket(18) with 2 pcs M10X65
Allen bolt (56), 4pcs Ø 10 washers(67) and 2 pcs M10 aircraft nuts (69).
Step 5
Assembly instructions

Assembly instructions
(A) Attach the sest pad support (1) to the front vertical frame(3) with one pc L shape lock pin(47) and one
pc M10X85 Lock knob(46).
(B) Insert the leg developer holder (24) into the front opening of seat pad support (1).You would select the
desired position with Lock knob (39).
(C) Attach the leg developer (7) to the bracket as the diagram shows, Secure them with one pc
Ø16*M10*57 axle (42),2 pcs M12*20 Allen bolt(65) and 2pcs Ø12 washers (71) .
Step 6
12

Assembly instructions
14

(A) Attach the upper cable (31) through the first bracket and make sure that the ball stopper should be
underneath the upper frame(4). lace one pc pulley (52) below the cable and secure the pulley with
one pc M10*45 allen bolt (57) , 2 pcs Ø 10 washers (67) and one pc M10 aircraft nut (69).
(B) Draw the cable backwards and place one pc pulley as the diagram shows, secure the pulley with 2 pcs
cable retainers(102) , 2pcs cable retainer bushings(103)with one pc M10*50 allen bolt (61) , 2 pcs Ø 10
washers (67) and one pc M10 aircraft nut (69).
(C) Draw the cable and place one pc pulley as the diagram shows ,Seucre them with one pc M10*180
allen bolt(53),2 pcs Ø10 washers (67), and one pc M10 aircraft nut (69).
(D) Draw the cable around the pulley and backwards and go through the opening of front vertical frame,
secure the pulley,2 pcs cable retainer(102) , 2pcs cable retainer bushing(103) with one pc M10*50
allen bolt (61) , 2 pcs Ø 10 washers (67) and one pc M10 aircraft nut (69).
(E) Draw the cable downwards and place one pc pulley onto the cable, secure the pulley with 2pcs double
floating pulley brackets (16),2 pcs cable retainers(102), 2pcs cable retainer bushings (103) with one pc
M10*50 allen bolt (61) , 2 pcs Ø 10 washers (67) and one pc M10 aircraft nut (69).
(F) Draw the cable around the pulley and upwards and go through the last opening of the upper frame, Fix
two pcs pulley as the diagram shows with 2pcs M10X50 Allen bolt(61), 2 pcs cable retainers(30), 4 pcs
Ø 10 washers (67) and 2 pcs M10 aircraft nuts (69).Draw the cable onto the 2pcs pulleys and then go
downwards through the central hole .
(G) Insert the selector pin (38) into the hole to select the desired weight when exercising . lace the ring of
the lock pin through the top of the select rod.
(H) Draw the cable downards ,Attach the end bolt to the top of selector rod, Thread at least 5 laps to
ensure the safety.
15
Step 7

Assembly instructions
16
14

(A). Attach one end of the butterfly cable (33) to the post of the upper right butterfly frame (6), Draw the
cable backwards and place one pc pulley below the cable. secure the pulley,2 pcs cable retainer(102) ,
2pcs cable retainer bushing(103) with the swivel pulley bracket (18) together with one pc M10*50 allen
bolt (61) , 2 pcs Ø 10 washers (67) and one pc M10 aircraft nut (69).
(B) Draw the cable downwards and place one pc pulley onto the cable.Secure the pulley,2 pcs cable
retainer(102) and angled floating pulley bracket(17) together with the same way in A.
(C) Draw the cable upwards and repeat the procedure B and A to fix another end of cable to the post of
upper left butterfly frame (5).
Step 8
Assembly instructions
17

Assembly instructions
18
AB
C
D
E
F

(A) Draw the lower cable (32) through the first bracket,make sure that the ball stopper should be in front of
the bracket. lace one pc pulley onto the lower cable, Secure the pulley , one pc cable retainer(102) ,
one pc cable retainer bushing(103) with one pc M10*50 allen bolt(61), 2 pcs Ø10 washers (67) and
one pc M10 aircraft nut(69) .
(B) Draw the cable backwards and go through the opening of the front vertical frame, lace one pc pulley
onto the cable and secure the pulley with the same method in A.
(C) Draw the cable around the pulley and upwards and place one pc pulley below the cable. Secure the
cable , 2 pcs cable retainer(102) , 2 pcs cable retainer bushing(103) with the same way in A.
(D) Draw the cable downwards and place one pc pulley onto the cable, Secure the pulley with the same
way in C.
(E) Draw the cable upwards and place one pc pulley below the cable.Secure the pulley with the doubel
floating pulley bracket with the same way in C.
(F) Draw the cable dowmwards and fix the end of the cable as the diagram shows with one pc M10*28
Allen bolt (55), 2 pcs Ø10 washers (67) and M10 aircraft nut(69).
Step 9

Assembly instructions
19