TOORX BRX RECUMBENT COMPACT User manual

Ed: 02/17 Rev : 00
INSTRUCTION

PRODUCT OVERVIEW
Back Cushion
Seat
Handle Bar
Meter
Back Support
Hand Pause
Adjustment Knob
Tension Knob
Right Pedal
Top Cover
Right Cover
Left Cover
Front Stabilizer
Rear Stabilizer
Leveling Cap
Wheel
Left Pedal
Left Crank
End cap
THEFOLLOWINGTOOLS ARE INCLUDED
Wrench:
FOR ASSEMBLY
Allen Wrench (5mm) w/ Screwdriver:

HARDWARE IDENTIFICATION CHART
Figure No.
Description Qty
D5
D8
Carriage Bolt (M8*1.25*60mm)
Carriage Bolt (M8*1.2548 mm)
4
2
D7 Bolt, Button Head (M6* 40 mm) 4
D22 Acorn Nut (M8) 4
D23 Arc Washer (M8) 6
D24 Washer (M8) 6
D25 Nut M8 2
D1 Adjustment Knob 2
D18
Pull Pin
1

A
AS SS SE EM MB BL LY Y I IN NS ST TR RU UC CT TI IO ON N
Place all parts from the box in a cleared area and position them on the floor in front of you.
Remove all packing materials from your area and place them back into the box. Do not
dispose of the packing materials until assembly is completed. Read each step carefully
before beginning.
STEP 1: Unfold the Rear Frame (A2) away from the Main Frame (A1). Locking the frame
assembly in unfold position by inserting the Pull PIN (D18) into the hole in the Rear
Frame (A2).
STEP2: Attach the Rear Stabilizer (A10), the one with Transport Wheels (B19), to the Rear
Frame (A2) with the wheels facing backward. Secure with Carriage Bolts
(M8*1.25*60mm) (D5), Acorn Nuts (M8) (D23), and Arc Washers (M8*1.25) (D22).
STEP 3: Attach the Front Stabilizer (A5) to the Main Frame (A1) with Carriage Bolts
(M8*1.25*60mm) (D22), Acorn Nuts (M8) (D23), and Arc Washers (M8*1.25) (D22).

A
AS SS SE EM MB BL LY Y I IN NS ST TR RU UC CT TI IO ON N
STEP 4: Attach the Seat (B24) to the Seat Post (A6) with Nylock Nuts (M8) (D25) and Washer
(M8) (D24). Insert the Seat Post (A6) into the Main Frame (A1) and secure with the
Adjustment Knob (D50).
NOTE:
Make sure that the pin on the Adjustment Knob (D50) is inserted into one of the holes in Seat
Post (A6).
STEP 5: Attach the Back Frame ( A7) and Seat Post (A6) by using Carriage Bolt (M8*1.25*48mm)
(D8) and Washer (M8) (D24).
Attach the Back Cushion (B25) and Back Support (A9) by using Button Head Bolt (M8*40)
(D7) and Washer (M8) (D24).
STEP 6: Attach the Handrail (A8) to the Back Frame (A7) with Button Head Bolts (M8*40) (D7)
and Arc Washer (D23). Connecting the Hand Pulse Button Line (C25) and Hand Pulse
Middle Line (C24).

A
AS SS SE EM MB BL LY Y I IN NS ST TR RU UC CT TI IO ON N
STEP7: Install Meter (C1) into the Meter Bracket (A14). Connecting the Hand Pulse Top Line
(C23) to the back of Meter (C1), And connect the Sensor (C13) and Connection
Wire( C2).
NOTE: Be careful not to damage the wires when attaching the Meter(C1).
STEP8: Lock and tight the Left Pedal (B27) and Right Pedal (B28) on the Left Crank (B29) and
Right Crank (B30) by using the Wrench.

OPERATIONAL INSTRUCITONS
USING THE FITNESS METER
MODE: This key lets you to select and lock on to a particular
function you want
SET(IF HAVE) :To set the values of time distance and calories when
not in scan mode
RESET/CLEAR (IF HAVE): The key to reset the value to zero by
pressing the key
FUNCTIONS:
SCAN: Automatically scans each function of SPEED,
DISTANCE,TIME, ODOMETER, CALORIES and
PULSE. in sequence, display changes every six seconds.
Press and release the button until "SCAN" appears on the
display.
TIME: Displays the time from one second up to 99:59 minutes
SPEED : Displays the current speed from zero to 999.9 KM per hour.
DISTANCE : Displays the distance from zero to 999.9 KM.
CALORIES: Displays the calories burned from zero to 999.9 Kcal.
The calorie readout is an estimate for an average user. It should be used only as a
comparison between workouts on this unit.
ODOMETER : Displays the total accumulated distance you have traveled from zero to 9999 KM. The
total accumulated distance is retained when the meter is turned off.
PULSE: Displays your pulse rate in beats per minute. To display pulse, select the PULSE MODE and
grasp the pulse sensors on the Desktop, one in each hand. The heart icon will begin flashing
when the ELECTRONIC METER senses your pulse. Your pulse will be displayed approximately
five (5) seconds after the heart icon is displayed. If the heart icon does not appear, relax your
grip or change your grip on the pulse sensors.
NOTE:
1. NOTE: The meter will shut off automatically after four minutes of inactivity. All function values
will be kept. Press the button and hold it down for two seconds to reset all functions to zero, except
ODOMETER.

LOAD ADJUSTMENT
To increase the load, turn the Adjustment Knob (B32) clockwise.
To decrease the load, turn the Adjustment Knob (B32) counterclockwise.
SEAT ADJUSTMENT
Proper seat adjustment is important.
1. Turn the Adjustment Knob (D50) to loosen, then pull the
Adjustment Knob (D50) to release the pin. Slide the
Seat Post (A6) until the Seat (B24) is at the proper
height. Release the Adjustment Knob (D50) making
sure the pin catches in one of the holes of the Seat Post
(A6) and tighten the Adjustment Knob (D50).
2. Sit on the seat and place your feet on the pedals. You
should be able to move through a complete pedal stroke
without locking your knees or shifting your hips on the
seat. The seat is too close to the pedals if you have
more than as light bend in your knees at the bottom of
the pedal stroke. The seat is too far from the pedals if
you have to completely straighten your knees at the
bottom of the pedal stroke. Refer to the illustration.
CAUTION:
1. Do not attempt to adjust the seat while you are on the BIKE.
2. Always tighten the Adjustment Knob (D50) after
adjusting the seat to a new position.

STORAGE
• To store the BIKE, simply keep it in a clean dry place.
• To avoid damage to the electronics, remove the batteries before storing the BIKE for one year or more.
• Follow the illustrated process below to fold the BIKE.
Remove the Pull Pin (D18) from the Rear Frame (A2).Fold the Rear Frame (A2) close to the Main
Frame (A1) and lock it in folded position with the Pull Pin (D18). And, folding down the Back Cushion
(B25).
NOTE: Make sure the Pull Pin (D18) goes through the holes on both sides of the Rear Frame (A2)
and the tube on the Main Frame (A1).
The safety and integrity designed into the BIKE can only be maintained when the BIKE is regularly
examined for damage and wear. Special attention should be given to the following:
1. Adjust the Adjustment Knob (B32) and verify that it functions properly and the resistance changes.
2. Use a wrench to verify that the pedals are tightened securely. If tightening is required, remember that
the left pedal has left hand threads and is tightened by turning counterclockwise.
3. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.
Tighten loose nuts and bolts.
4. It is the sole responsibility of the user/ owner to ensure that regular maintenance is performed.
5. Worn or damaged components shall be replaced immediately or the BIKE removed from service
until repair is made.
6. Keep your BIKE clean by wiping it off with an absorbent cloth after use.

T
OCO
N
T
ACTCUS
T
OMERSERVICE
14
PRODUCT PARTS DRAWING

T
OCO
N
T
ACTCUS
T
OMERSERVICE
15
PARTS LIST
A. Welding Parts
No.
Description
QTY
A1 Main Frame 1
A2 Rear Frame 1
A5 Front Stabilizer 1
A6 Seat Support 1
A7 Back Frame 1
A8 Handrail 1
A9 Back Support 1
A10 Rear Stabilizer 1
A12 Mangetic Bracket 1
A13 Shaft 1
A14 Meter Bracket 1
B. Plastic Parts
No.
Description
QTY
B1 Left Chain Cover 1
B2 Right Chain Cover 1
B3 Top Cover 1
B12 Sensor Bracket 1
B13 Bushing 1
B14 Plastic Bushing 6
B15 Oval Plug (20mm*40mm) 2
B16 Plastic Washer Φ8.5*Φ20*2.0T 2
B18 Leveling Cap 2
B19 Wheel 2
B20 Inner Plug 2
B21 Tube Bushing S30*30 1
B22 Tube Bushing S15*30 4
B24 Seat 1
B25 Back Cushion 1
B26 Foam Grip 400 2
B27 Left Pedal 1
B28 Right Pedal 1
B29 Left strap 1
B30 Right strap 1
B31 Crank Cap 2
B32 Adjustment Knob 1
B35 Plastic WasherΦ10.2*Φ14 2
B37 Stopper 1
B38 Endcap 2
B39 Bearing Housing 2
B40 Hand grip 2
B41 Rubber 1
B42 Square Plug S25*25 1
B43 Grommet Plug 3
B44 Plug 1
C. Electrical parts

T
OCO
N
T
ACTCUS
T
OMERSERVICE
16
No.
Description
QTY
C1 Meter 1
C2 Connection Wire 1
C5 Left Crank 1
C6 Right Crank 1
C7 Flywheel 1
C8 V-Ribbed Belt (230J) 1
C9 V-Ribbed Belt(240J) 1
C10 Pulley w/ Shaft 1
C11 Pulley Shaft 1
C12 Pulley 1
C13 Sensor 1
C14 Ball Bearing (6000ZZ) 2
C15 Ball Bearing (6200ZZ) 1
C16 Ball Bearing (6003ZZ) 2
C17 Idler Shaft 1
C18 Magnet 6
C19 Idler Shaft 1
C20 Magnet 1
C21 Hand Pulse 4
C23 Hand Pulse Top Line 620L 1
C24 Hand Pulse Middle Line 320L 2
C25 Hand Pulse Button Line 620L 2
D. Hardware
No.
Description
QTY
D4 Allen Wrench 1
D5 Carriage Bolt M8*60 4
D6 Hex Head Bolt M6*45 2
D7 Bolt, Button Head M8*40 6
D8 Carriage Bolt M8*48 2
D9 Bolt, Button Head M8*75 1
D10 Bolt, Button Head M8*20 2
D11 Eye Bolt M6 2
D15 Screw, Round Head ST4.2*16 6
D17 Bolt, Round Head (M6*12mm) 8
D18 Ball Pin 1
D19 Wave Washer S10 1
D20 Screw, Round Head ST4.2*25 1
D21 Flange Nu M10*1.25 2
D22 Acorn Nut M8 4
D23 Arc Washer M8 6
D24 Washer M8 12
D25 Nylock Nut M8 7
D26 Nut M10 2
D27 U-Shape Bracket 2
D28 Nylock Nut M6 2
D29 C Ring Φ17.0 6
D30 C Ring Φ10 2
D31 Wave Washer S17 1

T
OCO
N
T
ACTCUS
T
OMERSERVICE
17
D32 Spring Washer M8 1
D33 Large Washer(ø8.2*ø25*2mm) 2
D34 Nut M10 1
D35 Carriage Bolt M4X10 1
D36 Nylock Nut M10 1
D39 Nylock Nut M6 2
D41 Bearing Housing Cover 2
D42 Spring 1
D46 Bolt, Button Head ST5.0*15 1
D47 Wrench 13-15 1
D48 Bolt, Button Head M8*50 1
D49 Screw, Round Head ST4.0*20 2
D50 Adjustment Knob 1
D51 Screw, Round Head Self-Tapping ST4.2*16 2

GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
www.toorx.it - [e-mail]