Topens CF800 User manual

VER 23b
C030689
Fast Sliding Gate Opener
User’s Manual
Model:
TOPENS Website
www.topens.com
Email: [e-mail]
CF800
★Please read and follow all warnings, precautions and instructions before
installation and use.
★Periodic checks of the opener are required to ensure safe operation.
★Save this manual.

CONTACT US:
Visit: www.topens.com
Please record the product model, your email address etc.
in the spaces provided below. Refer to this list when contacting TOPENS
for technical service or assistance with your automatic gate opener.
Where did you purchase? (Amazon.com; Amazon.ca: Amazon.co.uk, Amazon.de; Other, Please
Specify)
Order#
Product Model
Purchase Date
Full Name
Phone#
Email Address (VERY
IMPORTANT)
Street Address, Apartment /Unit, City, State /Province, Zip Code
Country/Region
Approximate Gate Weight
(pounds; kg: Other. Please
Specify)
Approximate Gate Length
(feet; meter; Other. Please
Specify)
Did you purchase any
accessories? (Please list
below)
Issue Details
Email Us: [e-mail]
Call: [phone] (Toll Free USA & Canada)

Table of Contents
Check Your Gate before Installation.............................................................................................................1
General Safety ............................................................................................................................................1
Preparation for Installation...........................................................................................................................2
Parts List.....................................................................................................................................................4
Accessories Parts (Included in some models, refers to the actual package) ................................................4
Optional Accessories Parts List (Available at TOPENS Store) .....................................................................5
Replacement Parts......................................................................................................................................5
Technical Specifications & Features ............................................................................................................6
Installation Overview ...................................................................................................................................6
Installation of the Opener ............................................................................................................................7
Manual Operation........................................................................................................................................7
Installation of chain and chain brackets .......................................................................................................8
Installation of the Magnets...........................................................................................................................9
Connecting of Power Supply .....................................................................................................................10
Connecting of the Control Board................................................................................................................10
Setting of the Control Board ......................................................................................................................12
Test the Reversing Sensitivity....................................................................................................................13
How to Program or Erase the Remote .......................................................................................................13
How to Use the Remote to Operate Your Gate Opener..............................................................................14
Wireless Keypad Programming .................................................................................................................14
Troubleshooting.........................................................................................................................................15
Maintenance..............................................................................................................................................16

1
Thank you for purchasing our sliding gate opener. We are sure that the products will be greatly satisfying as
soon as you start to use it.
The product is supplied with a user ’s manual which encloses installation and safety precautions. These
should be read carefully before installation and operation as they provide important information about safety,
installation, operation and maintenance. This product complies with the recognized technical standards and
safety regulations.
CheckYourGatebeforeInstallation
GeneralSafety
WARNING! An incorrect installation or improper use of the product can cause damage to persons,
animals or properties.
• Scrap packing materials (plastic, cardboard, polystyrene etc.) according to the provisions set out by current
standards. Keep nylon or polystyrene bags out of children’s reach.
• This product was exclusively designed and manufactured for the use specified in the present
documentation. Any other use not specified in this documentation could damage the product and be
dangerous.
• The factory declines all responsibility for any consequences resulting from improper use of the product, or
use which is different from that expected and specified in the present documentation.
• Do not install the product in explosive atmosphere.
• The factory declines all responsibility for any consequences resulting from failure to observe Good
Technical Practice when constructing closing structures (door, gates etc.), as well as from any deformation
which might occur during use.
• Disconnect the electrical power supply before carrying out any work on the installation. Also disconnect
any buffer batteries, if fitted.
• Fit an omnipolar or magnetothermal switch on the mains power supply, having a contact opening distance
equal to or greater than 3,5 mm.
• Make sure a residual current circuit breaker with a 30mA threshold is fitted before the power supply mains.
• Check that earthing is carried out correctly: connect all metal parts for closure (doors, gates etc.) and all
system components provided with an earth terminal.
• Fit all the safety devices (photocells, electric edges etc.) which are needed to protect the area from any
danger caused by squashing, conveying and shearing.

2
• Position at least one visible indication device, and fix a Warning sign to the structure.
• The factory declines all responsibility with respect to the automation safety and correct operation when
other supplier’s components are used.
• Only use original parts for any maintenance or repair operation.
• Do not modify the automation components, unless explicitly authorized by the factory.
• Instruct the product user about the control systems provided and the manual opening operation in case of
emergency.
• Do not allow persons or children to remain in the automation operation area.
• Keep radio control or other control devices out of children’s reach, in order to avoid unintentional
automation activation.
• The user must avoid any attempt to carry out work or repair on the automation system, and always request
the assistance of qualified personnel.
• Anything which is not expressly provided for in the present instructions is not allowed.
• Before installing the gate opener, check that all moving part as well as the sliding gate is in good
mechanical condition, correctly balanced and opens and closes properly.
• Save these instructions for future use.
Preparationfor Installation
Before proceeding to your opener installation, check if your gate structure is in accordance with the current
standards, especially as follows:
The gate sliding track is linear and horizontal, and the wheels are suitable，the gate should be mounted and
moving freely. Check that the structure is sufficiently strong and rigid, Make sure that the gate is plumb and
level. The fence posts must be mounted in concrete. The gate does not bind or drag on the ground.
• The opening and closing gate stops are positioned.
WARNING: Remember that control devices are intended to facilitate gate operation, but can not
solve problems due to any defects or deficiency resulting from failure to carry out correct installation or
maintenance. Take the product out of its packing and inspect it for damage. Should it be damaged, contact
your dealer. Remember to dispose of its components (cardboard, polystyrene, nylon, etc.) according to the
current prescriptions.
Refer to the following Figures for gate installation.

3
In sake of safety, a positive stop must be mounted on the two end of ground track.

4
PartsList
AccessoriesParts (Includedin somemodels,refersto the actual package)

5
OptionalAccessoriesPartsList(Available at TOPENS Store)
M12 Remote Control
ERM12 External
Receiver
TC196 Tuya WIFI remote
control
TC188 Universal
Wireless and Wired
Keypad
TKP3 Wireless Keypad
TC175P Wired Keypad
HLR01 HomeLink
Remote Control Kit
TC173 Wireless Push
Button
TC147 Wall Push Button
TC148 Waterproof Wall
Push Button
TRF3 Reflection
Photocell Sensor
TC102 Photo Eye Beam
Sensor
JD110VY / JD230VY AC
Warning Light
LT08B 20 Feet Roller
Chain
TEW3 Vehicle Sensor
Exit Wand
ReplacementParts
ACPYMJ7C Control
Board (120V)
ACPYMJ8C Control
Board (230V)
PYMJ-CKG Limit Switch
Magnet Assembly(N
pole & S pole)
WARNING: Changes or modifications not expressly specified by this user manual, TOPENS could void
the warranty of this equipment.

6
TechnicalSpecifications& Features
Specifications
CF800
Power input:
110~120V/60Hz or 220~240V/50Hz
Motor voltage:
120VAC or 230VAC
Rated power:
450W
Gate moving speed:
40cm/s (16 in/s) for 120V
35cm/s (14 in/s) for 230V
Max gate weight:
800kg (1800lbs)
Environmentalconditions:
-20℃~ +50℃ (0°F to 120°F)
Protection class:
IP44
Features:
·Midway mode.
·Quick selection for the gate open/close direction
·Reliable rolling code technology for remote control
·Emergency release key in case of power failure
·Stop in case of obstruction during gate opening
·Reverse in case of obstruction during gate closing
·Built in adjustable auto-close (1-99 seconds)
·Built in max. Motor Running Time (MRT) for multiple
safety protection (90 seconds)
·Reliable electromagnetism limit for easy adjustment
·Can be equipped with a wide range accessories
·Easy to install, and minimum maintenance
requirement
·Get the desired chain tension by adjusting the chain
bolts
InstallationOverview

7
Installationof the Opener
Caution:
*Be sure that the opener is installedin a level
and paralleledposition.Improperinstallation
could resultin propertydamage, severe injury,
and/or death.
* Before starting installation, ensure that there
is no point of frictionduring the entire
movement of the gate and there is no danger of
derailment.
* Ensure that the safety side rollers are present.
NecessaryTools: The following tools may be
necessary to install the Gate opener. You will need
screwdrivers, an electric drill, wire cutters and a
wire stripper, a socket set, and possiblyaccess to a
welder.
When install the opener,you should build a
concrete pad to support the base plate of opener in
order to maintain proper stability.
The installation proceeds are as follows:
1.Assemble the Base Plate and fix the Opener to
the Base Plate.
2.Dig a hole for a concrete pad which should be
approximately 60 x 32 x 35cm (24〞x 13〞x 14〞).
It may protrude 10 cm (4”) above ground and 25 cm (10”) in depth underground. Increase the pad height if
necessary to protect the system from flooding, heavy snow etc.
3. Prepare one or more conduits for the electrical cables before pour concrete. Remember that cable
conduits have to pass through the hole on the base.
4. Pour concrete and before it starts to harden, check that it is parallel to the gate leaf and perfectly level.
5. Mark the position of four expansion anchors according to the position of mounting hole on the base plate.
Double checkyour marking, move the base plate and drill the 4 holes using a 14mm (9/16”) masonry bit. Put
the 4 expansion anchors (provided) into the holes and firmly tighten.
6. Mount the base plate to the concrete Pad and firmly tighten, enabling the opener is firmly secured
on the concrete pad during the whole gate travel.
ManualOperation
You can open the gate by manualwhen power failure. And the opener should be put in the manual
(emergency release) position before fitting the
chain, installing the opener and limit switch. The
process is as follows:
Insert the Release Key and turn it in clockwise
90°, then pull the release handle in clockwise 90°
to disengage the clutch between the gear shaft
and motor. Now the opener is in the manual
operation.

8
Installationof chainandchainbrackets
1. Chain Brackets
1). Please refer to below chain brackets figure,
which shows “U”bolt, “L”bracket and chain bolt.
Use the “U”bolts (square or round) to attach the
chain brackets to gate frame.
2). If Both the square bolts and round bolts are not
fit for the gate frame, use the appropriate bolts to
attach the chain brackets to gate frame.
2. How to install the chain
1). Place the chain around the top of the idler
wheels and under the drive sprocket in chain box.
2). Connect a chain bolt to one end of chain from
chain box by using master link. Then insert the
chain bolt to the L bracket and fix them each other
by washers and nuts temporarily. (Nuts will be
further adjusted for a proper chain tension later)
3). Connect second chain bolt with another end of chain from chain box, then attach bolt to the L bracket on
opposite end of gate using the washers and nuts.
4). Make sure that the chain is line up exactly with the position where
the chain on the chain idler wheel.
5). Remove the unwanted length of chain. Set appropriated chain
tension by adjusting two chain bolts of the both end.
6). The chain brackets must be mounted tothe same height asthe
chain on the idler wheels.

9
7). Make sure there is 1”distance at least between the wheel cover and the gate after you position the base
plate.
Installationof the Magnets
Before install limit switch, make sure the gate opener is put in manual operation. (the clutch connected with
gear shaft is disengaged) and the mains power supply is disconnected. Position the two Magnet
Components approximately on the gate and move the gate by hand to fix them in place.
Fit magnets bracket
Push the gate fully closed by hand. Locate and install the magnet bracket so that the opener will stop at the
desired close position when the close limit switch approaches it.
Push the gate fully open by hand. Locate and install the magnet bracket so that the opener will stop at the
desired open position when the open limit switch approaches it.
The magnet component with S pole must be installed at left side and the magnet component with N
pole must be installed at right side from the view inside of property.
Ensure magnet center to align with the marked line above !
The magnets should be 25~30mm (1-1.2”) away from the Limit Switch Box. If it is too near or too far, the
switches will fail to work. Adjust the position of the magnets until the positions of the opening and closing
meet the requirement.
Warning: Improper magnets installation may cause the gate crash into end barrier,
which is very dangerous !

10
Connecting of Power Supply
WARNING: NEVER connect the gate opener to the power
outlet before all the installations have been done.
The power supply cord should be at least 3×0.75mm2 (3C×18AWG).
Connect the live wire and neutral wire to the “L” (1) and “N” (2)
terminal of the control board respectively; and connect the earth wire
to “PE”.
Connectingofthe ControlBoard
1. Motor
The BLACK wire of the motor should be connected into the “3” terminal.
The YELLOW wire of the motor should be connected into the “4” terminal.

11
The RED wire of the motor should be connected into the “5” terminal.
2. Limit Switches
The YELLOW wire of the limit switches should be connected into the “8” terminal.
The BLACK wire of the limit switches should be connected into the “9” terminal.
The RED wire of the limit switches should be connected into the “10” terminal.
3. Warning Light (Included in some models, refers to the actual package)
One wire of the warning light should be connected into the “6” terminal, another should be connected into
the “7” terminal.
4. Start Capacitor
The two wires of the start capacitor should be connected into the “4”terminal and “5” terminal.
5. Photocell Beam System (PBS) (Included in some models, refers to the actual package)
Use a 2-core cable to connect the “+ ~” terminal of the photocell’s emitter to the “11” terminal, the “- ~”
terminal to the “13” terminal. Also the “+ ~” and “- ~” terminals of the photocell’s receiver should be
connected to the “11” and “13” terminals in parallel.
Use another 2-core cable to connect the “COM” terminal of the receiver to the “13” terminal, the “NC”
terminal to the “12” terminal.
6. Reflection Photocell Sensor (optional)
The “AC10-25V/DC12-30V” terminals of the reflection photocell sensor should be connected to the “11” and “13”
terminals, no matter the polarity.
The “NC” terminal should be connected to the “12” terminal.
The “COM” terminal should be connected to the “13” terminal.
7. Wired Keypad (12VDC) (Optional)
The RED wire of the wired keypad should be connected into the “11” terminal.
The BLACK wire of the wired keypad should be connected into the “13” terminal.
The PURPLE wire of the wired keypad should be connected into the “13” terminal.
The BLUE wire of the wired keypad should be connected into the “14” terminal.
8. Push Button (Optional)
The push button should be wired to the “13” and “14” terminals. The gate operator works alternately by
pushing the button (open-stop-close-stop-open).
9. External receiver (optional)
The RED wire of the external receiver should be connected into the “11” terminal.
The BLACK wire of the external receiver should be connected into the “13” terminal.
The BROWN wire of the external receiver should be connected into the “14” terminal.
10. HomeLink Remote Control Kit (optional)
The “1” terminal should be connected to the “13” terminal.
The “2” terminal should be connected to the “14” terminal.
The “DC+” terminal should be connected to the “11” terminal.
The “DC-” terminal should be connected to the “13” terminal.

12
11. Exit Wand (optional)
The BLACK wire of the exit wand should be connected into the “15” terminal.
The BLUE wire of the exit wand should be connected into the “16” terminal.
The RED wire of the exit wand should be connected into the“11” terminal.
The GREEN wire of the exit wand should be connected into the“13” terminal.
The sensitivity adjustment board should be wired to the GREEN wire and the YELLOW wire of the wand. No
matter the polarity.
Settingof the ControlBoard
WARNING: Ensure the gate opener is Power Off when you make any adjustment of the gate
opener. Keep away from the gate during you set the gate opener system in case of the unexpected
gate moving. Carefully adjust the DIP switches to avoid the risk of machine damage and injury or
death. Always ask the help of professional technician /electrician if you have any question .
1. DIP Switches
The DIP switches are used to set the running
time of the motor in pedestrian mode,
enable/disable auto close function of the gate
operator and fast change the open/close
direction which is determined by the position
of the gate operator installed.
DIP Switch #1–#2: Running time of the
motor in Midway Mode
DIP Switch #1: ON – 2 Seconds OFF – 0
DIP Switch #2: ON – 4 Seconds OFF – 0
NOTE: The midway mode function would be disabled if both DIP switches are turned off. Factory
default setting is disabled. The midway mode could be activated by pressing button B of the remote
control when the gate is in the full closed position.
DIP Switch #3: Auto close function enabled/disabled
DIP Switch #3: ON – auto close function enabled
OFF –auto close function disabled
Important Note: When the auto close function is enabled, the photocell sensor is highly
recommended to be installed with the gate opener for safety.
E.g. Running time of the operator in midway mode is 2 seconds.
E.g. Auto close function of the opener has been enabled. Factory default setting is disabled.

13
DIP Switch #4: Left/Right open
2. Potentiometers
Potentiometer A and B are used to adjust the stall force and auto close time of the gate operator separately.
Turn potentiometer A clockwise to increase the stall force, and turn it counter-clockwise to decrease the
stall force.
WARNING: Photocell is highly recommended to be installed with the gate opener as entrapment
protection for safety when you set stall force to maximum.
Turn potentiometer B clockwise to increase the auto close time, and turn it counter-clockwise to decrease
the auto close time, the auto close time could be adjusted gradually from 1 to 99 seconds.
Testthe ReversingSensitivity
For the sake of safety, it is very important to test the reversing sensitivity as soon as the control board set is
finished.
The reversing sensitivity adjustment is inverse correlation with stall force adjustment in potentiometer A. In
other word, the stall force level is higher; the reversing sensitivity level is lower.
Put an immobile object along the gate path, and then operate the gate to strike it during the close cycles.
The gate must reverse as soon as object is struck with it. If the gate doesn’t reverse, please increase the
reversing sensitivity by turning the potentiometer A in counter-clockwise direction. (Turning the stall force
potentiometer toward to MIN position to increase the reversing sensitivity)
Note 1: If the sensitivity setting is too higher, the gate will stop or reverses very easy by itself while
there is little obstruction or resistance such as strong wind or heavy snow sometimes.
Note 2: Always check the gate reversing function every each time of control board set or restart after
power off.
How to ProgramorErasethe Remote
The remote MUST be programed to the opener BEFORE OPERATING. Please follow the steps to
program the remote.
Activate the opener only when gate is in full view, free of obstruction and properly adjusted. No

14
one should enter or leave gate area while gate is in motion. DO NOT ALLOW CHILDREN to
operate push button or remote. DO NOT ALLOW CHILDREN TO PLAY NEAR THE GATE.
If you purchase additional remote controls, the gate opener must be programmed to accept the
new remote code.
If you lose one of any remote control, please
erase and reprogram all other remote controls
to have a new code for safety.
Program the remote
Press and release the LNSW button, the LEARN LED
light will be on, then press the key A or B on the
remote two times in 2 seconds, between the two
times HOLD ON FOR A MOM ENT, the LEARN LED
light will flash for 4 seconds. Now the remote has
been programmed successfully.
Erase all the remote codes
Press and hold the learn button until the LEARN light is off. Now all remote codes have been erased.
Max. 8 remotes can be programmed for the opener. An External Receiver (optional) allows up to
250pcs remotes to be programmed for the opener. TOPENS ERM12 Universal External Receiver is
available at TOPENS Store.
TOPENS ERM12 Universal External Receiver is also compatible with other brand swing gate
opener, sliding gate opener and garage door opener.
How to Use the Remote to OperateYourGateOpener
Each remote has four buttons, from top to bottom are separately A, B, C and D. You may use this remote to
operate as many as 4 sets TOPENS swing gate openers or 1 set TOPENS sliding gate opener and 2 sets
TOPENS swing gate openers.
1. Use this remote to only operate TOPENS swing gate opener A, B, C and D four
buttons share same function once they are programmed with
TOPENS swing gate opener. You may choose any button to program it with our
swing gate opener. Every press of the button is able to active the gate opener to
work alternately (open-stop-close-stop-open).
2. Use one remote to operate TOPENS swing gate opener & sliding gate opener
at the same time
All of TOPENS sliding gate opener have midway mode. Button B is designed to
realize midway function (refer to more details in our TOPENS sliding gate opener
manual). So it is must program button A with sliding gate opener, while you may program either C button or
D button with TOPENS swing gate opener.
WirelessKeypad Programming
You can follow the below steps to program wireless keypad to the opener. Press the LNSW button until the
LEARN LED is ON, and then releases the button. Then press "OK" button on keypad and LEARN LED will
flash for 3 seconds and then be OFF which indicates the keypad has been programmed successfully. You
can use the default password “888888” to operate the opener after programming. You can press “PIN” “8 8 8
8 8 8” and then press “OK” to confirm to operate the opener.
Also you can change the password of the keypad follow the below steps. Press “PIN” and then input the six

15
digits old password and then press ”PIN” again, the LEARN LED will be ON. Input the six digits new
password and then press the “PIN” to confirm the new setting, LEARN LED will flash for 3 seconds and then
be OFF which indicates the password has been changed successfully. You can press “PIN” “6 digits new
password” and then press “OK” to confirm to operate the opener.
NOTE: Every step for pressing button during program must be finished within 1 second to ensure successful
programming.
Troubleshooting
Have a multimeter to check voltage and continuity. Use caution when checking high voltage terminals.
Symptom
Possible Solution(s)
The opener does not
run.
1. Check the input voltage of the control board. It should be local AC
electricity.
2. Check the fuse in the control board. Replace the fuse if it was burnt out.
3. Ensure the remote control has been programmed to the control board
before operating.
4. The thermal protector is working because the high temperature after long
working time. Please wait for 20 minutes to let the motor become cold.
5. Check the installing position of the limit magnets. The opener would not
run if both of the limit switches are activated by one magnet.
6. Check the limit switch. Remove the wire connection of the limit switch
which is connected to the 8#, 9#, and 10# terminals of the control board and
then use a jumper wire to short the 3 terminals together to try it again.
Replace the limit switch if the motor could run in both directions.
7. Check the control board. Replace the control board as necessary.
Remote control does
not work.
1. The indicator light of remote control is not on. Check the battery in your
remote control. Replace the battery as necessary.
2. The distance you use the remote is too far away from the opener. Try it
again closer.
3. Remote control is not suitable for receiver. After making sure the codes are
correct, erase remote controls and then re-program the codes in the device.

16
Maintenance
Every six months checkthe following items for proper operation of the unit.
* Lubricate shafts and sprockets.
* Keep operator clean at all times.
* Check and tighten anchors bolts.
* Check for loose or corroded wire
* Ensure the operator is well earthed, and correctly terminated.
* Always check the Stop/Reverse in case of obstruction function when performing any maintenance. If
this function can’t be made operable, remove this operator from service until the cause of the
malfunction is identified and corrected.
4. Check the control board. Replace the control board as necessary.
The gate starts but it
is immediately stop or
reverse
1. Check the wire connection of hall sensor board with the main control
board.
2. The opening force or closing force is adjusted too small. Turn the
Potentiometer A to increase the force.
3. Disconnect the gate from the gate opener and check that the gate slides
freely without any binding.
4. Check the control board. Replace the control board as necessary.
The gate opens, but
stops and will not
return.
1. Check the installing position of the magnets. The opener would not run if
both of the limit switches are activated by one magnet.
2. Check the limit switch. Remove the wire connection of the limit switch
which is connected to the 8#, 9#, and 10# terminals of the control board and
then use a jumper wire to short the 3 terminals together to try it again.
Replace the limit switch if the motor could run in both directions.
3. Check the control board. Replace the control board as necessary.
The gate can open,
but fails to close.
1. Photocell is obstructed. Remove obstruction.
2. Check the limit switch. Remove the wire connection of the limit switch
which is connected to the 8#, 9#, and 10# terminals of the control board and
then use a jumper wire to short the 3 terminals together to try it again.
Replace the limit switch if the motor could run in both directions.
3. Check the control board. Replace the control board if necessary.
The gate will open
automatically instead
of close after the auto
close time
Ensure the DIP 4# has been set correctly according to the installation for
“Left Open” or “Right Open”
The motor runs but
the gate doesn’t
move.
Ensure the clutch for emergency release is adjusted properly and is not
slipping.

Feedback & Review
Your comments and suggestions are important to us
as they help us provide the best possible service.
Should you have any need to contact us, the info below will help you get in touch:
TOPENS Website
www.topens.com
Contact Us:
E-mail: [e-mail]
Kindly include your Product Model, Purchasing Date & Site, Order #,
and your contact information. All your concerns will be replied within 24 hours.
Tel: [phone] (Toll Free USA & Canada)