Topens Mk1101 User manual

Swing Gate Opener

User’s Manual

Model:

VER 21a

C030009

MK1101 / MK1102

MK1301 / MK1302

MK1101M / MK1102M

MK1301M / MK1302M

MK1501M / MK1502M

★Please read and follow all warnings, precautions and instructions before

installation and use.

★

Never connect the solar panel to the control board directly to charge the battery.

★Periodic checks of the opener are required to ensure safe operation.

★

Save this manual.

Table of Contents

Safety Installation Information.......................................................................................................................... 1

Dual Gate Opener Parts List............................................................................................................................ 2

Single Gate Opener Parts List .........................................................................................................................3

Optional Accessories Parts List........................................................................................................................4

Tools Needed: .................................................................................................................................................. 4

Technical Specifications & Features................................................................................................................5

Dual Gate Overview......................................................................................................................................... 7

Single Gate Overview.......................................................................................................................................8

Preparation for Installation............................................................................................................................... 8

Install the Gate Opener on the Gate................................................................................................................9

Mounting of the Control Box...........................................................................................................................13

Connection of the Power Supply.................................................................................................................... 14

Connection of the Control Board.................................................................................................................... 15

Motor connection for PULL-TO-OPEN ...............................................................................................................16

Motor connection for PUSH-TO-OPEN ..............................................................................................................16

How to learn or erase the Remote.................................................................................................................17

Setting of the Control Board...........................................................................................................................18

Indicate Illustration on the Digital Display When Gate Opener is Running................................................... 20

Adjusting the Limit Switch.............................................................................................................................. 21

How to Operate.............................................................................................................................................. 21

Maintenance................................................................................................................................................... 21

Trouble Shooting............................................................................................................................................22

Quick-Setting Guide.......................................................................................................................................23

Safety Installation Information

1. READ and FOLLOW all instruction.

2. The gate opener is intended for use with Class I

vehicular swing gates.

Class I denotes a vehicular gate opener (or system)

dwellings, or a garage or parking area associated

therewith.

Install the gate opener only when the opener is

appropriate for the construction and the usage class of

the gate.

3. Gate opening system designers, installers and

users must take into account the possible hazards

associated with each individual application. Improperly

designed, installed or maintained systems can create

risks for the user as well as the bystander. Gate

system design and installation must reduce public

exposure to potential hazards. All exposed pinch

points must be eliminated or guarded.

4. A gate opener can create high levels of force

during normal operation. Therefore, safety features

must be incorporated into every installation. Specific

safety features include safety sensors.

5. The gate must be properly installed and work

freely in both directions prior to the installation of the

gate opener.

6. The gate must be installed in a location so that

enough clearance is provided between the gate and

adjacent structure when opening and closing to

reduce the risk of entrapment. Swinging gates shall

not open into public access areas.

7. The opener is intended for use only on gates used

for vehicles. Pedestrians must be supplied with a

separate access opening. The pedestrian access

opening shall be designed to promote pedestrian

usage. The pedestrian access shall be located such

that persons will not come in contact with the moving

vehicular gate.

8. Pedestrians should never cross the pathway of a

moving gate. The gate opener is not acceptable for

use on any pedestrian gate. Pedestrians must be

supplied with a separate pedestrian access.

9. For an installation utilizing non-contact sensors

(safety sensors), see product manual on the

placement of non-contact sensors (safety sensors) for

each type of application.

a. Care shall be exercised to reduce the risk of

nuisance tripping, such as when a vehicle trips the

safety sensor while the gate is still moving.

b. One or more non-contact sensors (safety sensors)

shall be located where the risk of entrapment of

obstruction exists, such as the perimeter reachable by

a moving gate or barrier.

10. Never mount any device that operates the gate

opener where the user can reach over, under, around

or through the gate to operate the controls. Controls

are to be placed at least 6’(1.8m) from any part of the

moving gate.

11. Controls intended to be used to reset an operator

after 2 sequential activations of the entrapment

protection device or devices must be located in the

line of sight of the gate, or easily accessible controls

shall have a security feature to prevent unauthorized

use. Never allow anyone to hang on or ride the gate

during the entire travel of the gate.

12. Each gate opener is provided with two safety

warning placards. The placards are to be installed on

the front and back of the gate where they are plainly

visible. The placards may be mounted using cable ties

through the four holes provided on each placard.

All warning signs and placards must be installed

where visible in the area of the gate.

13. To AVOID damaging gas, power, or other

underground utility lines, contact underground utility

locating companies BEFORE digging.

SAVE INSTRUCTION.

14. Do not permit children to play on or around the

gate and keep all controls out of their reach.

Dual Gate Opener Parts List

Single Gate Opener Parts List

Optional Accessories Parts List

Tools Needed:

·Power Drill ·Tape Measure ·Open End Wrenches - 14# &17# orAdjustable Wrenches

·Wire Strippers ·C-Clamps - small, medium, and large ·Level ·Hacksaw or Heavy Duty Bolt Cutters

·Phillips Screwdriver ·An extra person will be helpful

Technical Specifications & Features

Specifications

MK1101/1102

MK1101M/1102M

MK1301/1302

MK1301M/1302M

MK1501M/1502M

Input:

110V~120V/60Hz or 220~240V/50Hz

Motor voltage:

24VDC

Power:

50W each actuator

80W each actuator

100W each actuator

Current:

Actuator speed:

20mm/s（0.8 in/s）

Max. actuator travel:

385mm（15.2 in）

485mm（19 in）

Ambient Temperature:

-22℃~ +55℃(-4°F to 122°F)

Protection class:

IP44

Gate Capacity of MK11

Gate Weight

300kg(660lbs)



250kg(550lbs))



200kg(440lbs))



150kg(330lbs)



100kg(220lbs)



70kg(150lbs)



50kg(110lbs)



1.5-2m(5-7')

2.5m(8')

3m(10')

3.5m(12')

4m(13')

5m(16')

5.5m(18')

Gate Length

Gate Capacity of MK13

Gate Weight

400kg(880lbs)



350kg(770lbs)



300kg(660lbs)



250kg(550lbs)



200kg(440lbs)



150kg(330lbs)



100kg(220lbs)



1.5-2m(5-7')

2.5m(8')

3m(10')

3.5m(12')

4m(13')

5m(16')

5.5m(18')

Gate Length

Gate Capacity of MK15

Gate Weight

450kg(990lbs)



400kg(880lbs)



350kg(770lbs)



300kg(660lbs)



200kg(440lbs)



150kg(330lbs)



100kg(220lbs)



1.5-2m(5-7')

2.5m(8')

3m(10')

3.5m(12')

4m(13')

5m(16')

5.5m(18')

6m(20')

Gate Length

Features:

·Soft start and soft stop

·Emergency release key in case of power failure

·Dual/Single gate running mode

·Adjustable opening/closing interval between master and slave gate

·Stop in case of obstruction during gate opening.

·Reverse in case of obstruction during gate closing.

·Built in adjustable auto-close (0-99 seconds)

·Built in max. Motor running time (MRT) adjustable for multiple safety protection (1-50 seconds)

·Digital display indicates the running situation and setting menu

·Can be equipped with a wide range of accessories

·Reliable electromagnetism limit for easy adjustment

·Easy to install, and minimum maintenance requirement

Dual Gate Overview

Single Gate Overview

Preparation for Installation

There are two installation types for the gate opener, Pull-to-Open and Push-to-Open.

In the Push-to-Open installation, gate opens out from the property. A Push-To-Open Bracket (PSO part) is

required to be used for each gate.

The gate opener is mounted to the gate and to the gate post. Both round and square posts can be used

because the Post Brackets are curved. When mounting the Post Brackets, use bolts long enough to pass

through the entire post. M10 x 200 bolts are included. Concrete anchors are not provided.

When mounting the Post Brackets to wooden posts, a larger-size washer or metal plate should be used

between the bolts and the wooden post to ensure the stability of the fastening hardware. If the post is smaller

than 6" diameter or square, it should be made of metal and set in cement to ensure its stability.

NOTE: Ensure the gate does not open into public areas.

Install the Gate Opener on the Gate

The position of Post Bracket is very important. The following illustrations and tables are required to determine

the proper mounting position for the Post Bracket. The tables show the maximum opening angle of the gate for

a given A and B. For example, if A is 16cm and B is 14cm, the maximum opening angle of the gate is 110°

Pull-to-Open Installation —Gate in Closed position (Moving-Rod is extended)

Push-to-Open Installation —Gate in Closed position (Moving-Rod is retracted)

1. Insert the M10 x 30 bolt through the center hole of the post bracket and

post pivot bracket as shown. Place a ￠10 washer , ￠10 lock washer and

M10 nut on the bottom of the bolt and hand tighten.

2. Attach the gate bracket and post bracket assembly to the opener by

inserting a clevis pin. Secure the clevis pins using the hairpin clips.

3. Open the release hole plug on the top of the gate opener, insert the release

key, and turn the key 90°clockwise. This releases the motor and allows the

push-pull rod to be manually extended and retracted. To restore normal

operation, turn the key 90°counterclockwise.

4. With the opener fully retracted and with the gate in the fully open

position (for Pull-to-Open installation) or fully closed position (for

Push-to-Open installation), place the gate opener with the Post Bracket

Assembly and Gate Bracket on the gate post and the gate. Position the Post

Bracket Assembly and Gate Bracket so that the gate opener is level. While

holding the gate opener in the level position, temporarily secure it with two

C-clamps.

5. Make sure that there is a minimum clearance of 2.5cm between the gate and the opener and that the opener

and the Post Pivot Bracket are not binding in both the gate-open and gate-closed positions. If there is not at

least 2.5cm of clearance or if the opener and the Post Pivot Bracket are binding, rotate the Post Pivot Bracket

and/or move the Post Bracket Assembly to obtain the minimum clearance and eliminate the binding. When the

minimum clearance has been obtained and any binding has been eliminated, place the M8 x 30 bolt through the

aligned holes in the Post Bracket and the Post Pivot Bracket.

6. Sign the bolt-hole point on the gate bracket and gate. Do this by placing a

punch or a sign in the middle of each bolt slot on the post bracket assemblies

and the gate bracket. It allows slight adjustments to the post bracket. Then

remove the post bracket and gate bracket by taking off the C-clamps.

7. Drill 10.5 mm diameter holes through the post and the gate at the marked

locations.

8. Attach the post bracket assemblies to the gate posts by inserting M10 x

200 bolts through each post bracket assembly and the drilled holes in the

gate post. Fasten each bolt with one ￠10 washer, one ￠10 lock washer,

and one ￠10 nut.

9. Attach the gate brackets to each gate by inserting two M10 x 75 bolts through the gate brackets and the

drilled holes in the gates. Fasten each bolt with one ￠10 lock washer, and one ￠10 nut.

10. Cut off any part of the bolts that extend beyond the tightened nuts.

11. With the gate opener fully retracted and with the gate in the fully open position (for Pull-to-Open installation)

or fully closed position (for Push-to-Open installation), attach the gate opener to the Post BracketAssembly and

the Gate Bracket by inserting a clevis pin through the gate opener and the Post Pivot Bracket and another clevis

pin through the gate opener and the Gate Bracket. Secure each clevis pin with a hairpin clip.

12. Open the release hole plug on the top of the gate opener, insert the release key, and turn the key 90°

counterclockwise. This restores normal operation.

NOTE: The setting of the PULL/PUSH TO OPEN of the control board should be in accordance with the

installation.

Mounting of the Control Box

1.To install the control box use the deck screws (not provided).

Even though the control box is waterproof designed, for safety reason and

a longer service life, it is recommended to install the control box inside a

secure surface and at least 100 cm (40 inches) above the ground to avoid

being flooded or buried under snow.

2.Insert the power cable and cable of the first gate opener through the front

strain relief and into the control box by loosening the strain relief screw

located in the leftmost of outside bottom of the control box and feeding the

cables into the control box. Check the length of cables is long enough to

their respective terminal block in control box.

CAUTION: Install the Control Box in a well ventilated place protected against rain and

sunlight.

3.Insert the cable of the second gate opener and alarm lamp cables into the control

box through middle strain relief. Then repeat step 2.

4. Insert other cables into the control box through rightmost strain relief. Then repeat

step

NOTE: Only motor cables (1.5m length) are provided. Other cables are subject to site

installation requirement and not provided.

CAUTION: Make sure the cable outlet hole in the Control Box is always down during

installation so as to drain off the water.

Connection of the Power Supply

WARNING: NEVER connect the gate opener to the power outlet before all the installations have

been done.

The live line and the neutral line should be connected to the power input terminals as the below photo. No

matter the polarity. The wire (not provided) size should be at least 0.75mm2 (18AWG) which is intended to

connect the power supply.

Connection of the Control Board

Motor connection for PULL-TO-OPEN

Actuator 1

Insert the stripped cable wires into the appropriate terminals on the opener terminals block. The red wire

should be inserted into the “MOTOR1+” terminal, the black wire into “MOTOR1-“, the blue wire into ULT1, the

green wire into COM, and the yellow wire into DLT1 terminal.

Actuator 2

Similar as the connection of Actuator 1, insert the stripped cable wires into the appropriate terminals on the

opener terminals block. The red wire should be inserted into the MOTOR2+ terminal, the black wire into

MOTOR2-, the blue wire into ULT2, the green wire into COM, and the yellow wire into DLT2 terminal.

NOTE: It is recommended that Gate Opener 1 is installed in the Master Gate, and Gate Opener 2 is installed in

the Slave Gate.

Motor connection for PUSH-TO-OPEN

The motors’ power wires and limit wires connection by “Push to

Open” is different from the connection by “Pull to Open”. So motor

1 and motor 2 wires should be connected to the control box as the

instruction on the right. The black wire should be inserted into the

Motor+ terminal, the red wire should be inserted into the Motor-

terminal, the yellow wire into ULT1 terminal, the blue wire into

DLT1 terminal and the green wire is still into COM terminal.

Alarm Lamp (optional)

The red wire of the alarm lamp should be inserted into either LAMP

(#11) terminal, the white wire into the other one (#12).

Back-up Battery (optional)

The “24V+” of the battery should be wired to the BAT+ (#13) terminal, “24V-” should be wired to “BAT-” (#14)

terminal.

Recommend strongly to use the controller LM118 (WA4004

）

to connect Battery with battery’s Terminal

of control board if the battery is used as the primary power supply in system (such as SOL PLUS KIT).

Please refer to the user manual of control LM118

（

WA4004

）

separated.

Photocell Beam System (PBS) (optional)

Use a 2-core cable to connect the “- ~”terminal of the photocell’s emitter to the “14” terminal, the “+ ~”terminal

to the “9” terminal.Also the “- ~”and “+ ~”terminals of the photocell’s receiver should be connected to the “14”

and “9”terminals in parallel.

Use another 2-core cable to connect the “COM”terminal of the receiver to the “17”terminal, the “NC”terminal

to the “18”terminal.

Push Button (optional)

The push button should be wired to the “19” and “20” terminals. The gate operator works alternately by pushing

the button (open-stop-close-stop-open).

WARNING: Activate the opener only when gate is in full view, free of obstruction and properly adjusted. No

one should enter or leave gate area while gate is in motion. Do not allow children to operate push button or

remote. Do not allow children to play near the door.

Your swing gate opener receiver and remote control transmitter are set to a matching code. If you purchase

additional remote controls, the gate opener must be programmed to accept the new remote code.

Caution: If you lose one of any remote control, please

learn all other remote controls to have a new code for

Loop Detector (optional)

First insert the LOOP DETECTOR BOARD into the CONTROL BOARD, and then connect the LOOP

DETECTOR to the control board. Detailed instruction please refers to the manual instruction of LOOP

DETECTOR separated.

Exit Wand (optional)

Please refers to the manual instruction of EXIT WAND separated.

Electric Lock (optional)

The electric lock should be wired to the “LOCK” terminal.

External Receiver (optional)

The BROWN wire of the external receiver should be connected into the “19” terminal.

The BLACK wire of the external receiver should be connected into the “20” terminal.

The RED wire of the external receiver should be connected into the “9” terminal.

Wired Keypad (24VDC) (optional)

The RED wire of the wired keypad should be connected into the “9” terminal.

The BLACK wire of the wired keypad should be connected into the “14” terminal.

The WHITE wire of the wired keypad should be connected into the “19” terminal.

The BLUE wire of the wired keypad should be connected into the “20” terminal.

Solar Panel(optional)

Please refer to the manual instruction of solar panel and controller (LM118) separated.

How to learn or erase the Remote

Learn the remote

Press and release the learn button, the LED will display “Ln”, then press the key in the remote twice in 2

seconds, the LED will flash “Ln” for 4 seconds then back to “- -”. Now the remote has been learnt successfully.

Erase all the remote codes

Press and hold the learn button until the LED display “dL”,

release the button and the LED will be back to “- -”. Now

all remote codes have been erased..

Setting of the Control Board

1. Check again for completed and correct assembly of your swing gate opener

and gate. Plug the Power Grounded Cord into the nearestAC outlet. The Digital

Display on the Control Board will flash with “- -”. The unit is in standby.

2. Single/Dual Gate Set

Press and hold the “FUNC”button for more than 4 seconds. The Digital Display

will indicate“P1”. Gate opener is on the SINGLE/DUAL Gate setting. Press the

“INC”and “DEC”buttons respectively to following modes:

“01”shown in Digital Display, it is Single Actuator 1 (Gate 1) mode. “10”shown

in Digital Display, it is SingleActuator 2 (Gate 2) mode. “11”shown in Digital Display, it is Dual actuator mode.

Press the “FUNC”button to store the data when the single or dual gate is chosen. The Digital Display will

indicate “P2”. Now single/dual gate set is finished.

(Factory set is “11”)

3. Master/Slave Gate Set

When Digital Display indicates “P2”, the gate opener is on the Master/Slave Gate Setting. Press the “INC” and

“DEC” Buttons respectively to follow modes:

“01”shown in Digital Display, which means Gate Opener 1 (right-hand side) as Master one

“10”shown in Digital Display, which means Gate Opener 2 (left-hand side) as Master one

Press the “FUNC”button to store the data when the master/slave gate is chosen. The Digital Display will

indicate “P3”. Now Master/Slave Gate Set is finished.

(Factory set is “01”)

4. Set the Open Interval between Master and Slave Gate

When the Digital Display indicates “P3”, the gate opener is on the Open Interval between Master/Slave Gate

Setting.

The open interval can be adjusted by pressing the “INC” and “DEC” Buttons respectively. The Digital Display

will show “0”-“9”, which indicates the interval time “0”means the Master and Slave gates open simultaneously.

“1”means the Master Gate starts to open 1 second before Slave gate starts to open. Max. open interval is 9

seconds. Each time you press and release the “INC”button, the figure increases by 1, and the Master gate

starts to open 1 more second earlier. Each time you press and release the “DEC”button, the figure decreases

by 1, and the interval decreases by 1 second.

(Factory set is 3 seconds)

Press the “FUNC”button to store the data when the open interval is set. The Digital Display will indicate “P4”.

Now Open Interval Set is finished.

5. Set the Close Interval between Master and Slave Gate

When the Digital Display indicates “P4”, the gate opener is on the Close Interval between Master/Slave Gate

Setting.

The close interval can be adjusted by pressing the “INC” and “DEC” buttons respectively. The Digital Display

will show “0”-“9”, which indicates the interval time ”0”means the Master and Slave gates open

simultaneously. ”1”means the Slave Gate starts to close 1 second before Master gate starts to close. Maximum

close interval is 9 seconds. Each time you press and release the “INC”button, the figure increases by 1, and the

Slave gate starts to close 1 more second earlier. Each time you press and release the “DEC”button, the figure

decreases by 1, and the interval decreases by 1 second.

(Factory set is 3 seconds)

Press the “FUNC”button to store the data when the close interval is set. The Digital Display will indicate “P5”.

Now Close Interval Set is finished.

6. Adjust the Obstruction Sensitivity/Stall Force

This manual suits for next models

Popular Gate Opener manuals by other brands

Casanoov

Casanoov TANKER B350 instruction manual

CAME

CAME F1000 installation manual

SOMFY

SOMFY 3S io user manual

BFT

BFT E5 BT A18 Installation and user manual

RIB

RIB BOSS 230V MASTER DX manual

Linear

Linear SWG installation guide

US Automatic

US Automatic PATRIOT RSL Installation & owner's manual

US Automatic

US Automatic PATRIOT RSL Installation & owner's manual

Keyautomation

Keyautomation REVO Instructions and warnings for installation and use

GiBiDi

GiBiDi BL240 Instructions for installation

HySecurity

HySecurity HYNET SFP 4/1 installation manual

Keyautomation

Keyautomation SUN Series Instructions and warnings for installation and use

Entrematic

Entrematic Ditec FACIL Technical manual

Power Master

Power Master rsw installation manual

Keyautomation

Keyautomation CT102 24 Instructions and warnings for installation and use

Keyautomation

Keyautomation STAR3024 Instructions and warnings for installation and use

HySecurity

HySecurity SwingSmart DC 20 Installation and reference manual

GiBiDi

GiBiDi AUTOBOX 3000 Instructions for installation

Topens MK1101 User manual

Popular Gate Opener manuals by other brands