Toro 95-3350 User manual

FormNo.3364-365RevC
CEUpdateKit
Aerator686and687
ModelNo.95-3350
InstallationInstructions
Safety
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea
ofpotentialdanger.Replaceanydecalthatisdamagedormissing.
decal95-3357
95-3357
686AeratorOnly
1.Warning—readthe
Operator’sManual.
2.Highpressureuid,
injectionintobody
hazard—seekmedical
attention.
decal93-6696
93-6696
1.Storedenergyhazard—readtheOperator'sManual.
©2022—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3364-365*

Installation
RelocatingtheManualTube
1.Parkthemachineonalevelsurface,lowerthe
cuttingunits,engagetheparkingbrake,shutoff
theengine,andremovethekey.
Note:Ifthemanualtubeismountedtotherear
ofthemainframemember,removeitandinstall
itonthefrontoftheaeratorsothatyoucan
accessthemanualaftertheguardsareinstalled.
Ifyouareinstallingthemanualtubeonthefront
ofthemachine,proceedtoMountingtheGuard
Assembly(page3).
2.Removethe2poprivetsthatsecurethemanual
tubemountingclampstotherearofthemain
frame(Figure1).
g014060
Figure1
1.Manualtube2.Mainframe
3.Mountthemanualtubetotheaerator.
•Forthe686Aerator:
A.Usethemanualtubeandclamp
assemblyasatemplatetomarkand
drill2holes(3/16inch)intheunderside
ofthelefttongueassembly(belowthe
handpump).
Note:Positiontheclampsabout6
inchesapart(Figure2).
g014061
Figure2
1.Tongueassembly2.Manualtube
B.Securetheclampstothetongue
assemblywith2poprivets.
•Forthe687Aerator:
A.Usethemanualtubeandclamp
assemblyasatemplatetomarkanddrill
2holes(3/16inch)inthefrontofthe
hitchassembly.
Note:Positiontheclampsabout6
inchesapart(Figure3).
g014062
Figure3
1.Tongueassembly2.Manualtube
B.Securetheclampstothehitchassembly
with2poprivets.
2

MountingtheGuard
Assembly
1.Positiontheguardassemblyontothemain
framearmsuntilthe4U-clampsstraddlethe
armsandtheguardopeningsarecenteredover
thesprings(Figure4).
g014063
Figure4
1.Guardassembly3.Mainframe
2.U-clamp
2.LooselysecuretheU-clampstothearmsby
insertingtheretainingboltsintotheweldnutson
theU-clamps(Figure4).
3.Installtheremainingguardsthesamewayand
tightenallthemountingfasteners.
MountingtheJackMount
(686AeratorOnly)
1.ObtainaJackKit(T oroPartNo.106-9660)from
anauthorizedT orodistributor.
2.Alignthejackmountholeswiththeholesinthe
righttongueassembly(Figure5).
Note:Positionthejackmounttubetowardthe
front.
g014064
Figure5
1.Jackmount2.Jackassembly
3.Securethejackmounttothetongueassembly
withboltsandlocknuts(Figure5).
4.Tightentheboltsto2.2tokg/m(16to18ft-lb).
3

InstallingtheCEDecals
Note:Thoroughlycleantheareawhereyouare
goingtoapplythedecalandletitdrybeforeplacing
thedecal.
Forthe687Aerator:
1.Placethe93-6696decalsontheleftandrightlift
armsasshowninFigure6.
g224309
Figure6
1.93-6696decallocation
2.Placethe138–9470decalonthemaintubeas
showninFigure7.
g415479
Figure7
1.138–9470decallocation
Note:Decal95-3357isnotusedon687aerators.
Forthe686Aerator:
1.Placethe93-6696decalontheleftandright
sidesoftheliftarms,directlybelowwherethe
cylinderattachesasshowninFigure8.
g224360
Figure8
1.93-6696decallocation
2.Placedecal95-3357onthehandpumpandthe
cylinderasshowninFigure9.
g224361
Figure9
1.95-3357decallocation
4