Weider PRO 4250 User manual

I®
Model No. 831.154020
Serial No.
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
• Assembly
•Adjustments
•Troubleshooting
•Part List and Drawing
WEIGHT SYSTEM EXERCISER
User's Manual
Patent Pending
_i_CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference. Sears, Roebuck and Co., Hoffman Estates, IL 60179

TABLE OF CONTENTS
WARNING DECAL PLACEMENT ............................................................. 2
IMPORTANT PRECAUTIONS ................................................................ 3
BEFORE YOU BEGIN ...................................................................... 4
ASSEMBLY .............................................................................. 5
ADJUSTMENTS .......................................................................... 23
WEIGHT RESISTANCE CHART .............................................................. 25
CABLE DIAGRAM ......................................................................... 26
MAINTENANCE .......................................................................... 28
EXERCISE GUIDELINES .................................................................. 29
ORDERING REPLACEMENT PARTS .................................................. Back Cover
FULL 90-DAY WARRANTY .......................................................... Back Cover
Note: APART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of
this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin-
ning assembly.
WARNING DECAL PLACEMENT
The decal shown here
has been placed on the
weight system. If the
decal is missing or illegi-
ble, please call toll-free
1-877-992-5999, Monday
through Friday, 6 a.m.
until 6 p.m. Mountain
Time, and order a free
replacement decal. Apply
the decal in the location
shown.
2

IMPORTANT PRECAUTIONS
_WARNING: To reduce the risk of serious injury, read the following important precautions
before using the weight system.
1o
2.
Read all instructions in this manual before
using the weight system. Use the weight sys-
tem only as described in this manual.
It is the responsibility of the owner to ensure
that all users of the weight system are ade-
quately informed of all precautions.
9. Keep hands and feet away from moving parts.
10. Make sure that the cables remain on the pul-
leys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys. Replace all
cables at least every two years.
3. The weight system is intended for home use
only. Do not use the weight system in any
commercial, rental, or institutional setting.
4. Use the weight system only on a level sur-
face. Cover the floor beneath the weight sys-
tem to protect the floor.
5.
6.
7.
8.
11. Always secure the weight stack with the lock
pin and lock after exercising to prevent
unauthorized use of the weight system (see
LOCKING THE WEIGHT STACK on page 24).
12. Always stand on the foot plate when per-
forming an exercise that could cause the
weight system to tip.
Make sure all parts are properly tightened
each time the weight system is used.
Replace any wom parts immediately.
Keep children under 12 and pets away from
the weight system at all times.
The weight system is designed to support a
maximum user weight of 300 pounds.
Always wear athletic shoes for foot protec-
tion while exercising.
13. Never release the arms, leg lever, lat bar, leg
press, ab strap, or handle while weights are
raised. The weights will fall with great force.
14. Always disconnect the fat bar from the
weight system when performing an exercise
that does not use the lat bar.
15. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3

BEFORE YOU BEGIN
Thank you for selecting the versatile WELDER" PRO
4250 weight system. The weight system offers an
impressive array of weight stations designed to devel-
op every major muscle group of the body. Whether
your goal is to tone your body, build dramatic muscle
size and strength, or improve your cardiovascular sys-
tem, the weight system will help you to achieve the
specific results you want.
For your benefit, read this manual carefully before
using the weight system. Ifyou have questionsafter
reading this manual, call 1-800-4-MY-HOME ®
(1-800-469-4663). To help us assist you, please note
the producl model number and serial number before
calling. The model number is 831.154020. The serial
number can be found on a decal attached to the
weight system (see the front cover of this manual for
the location of the decal).
Before reading further, please review the drawing
below and familiarize yourself with the pads that are
labeled.
Right Side
High Pulley Station
Butterfly Arm
Ab Pulley Station
Backrest
Seat
Leg Level
Low Pulley
Station Weight
Stack
ASSEMBLED
DIMENSIONS:
Height: 77 in.
Left Side Width: 81 in.
Depth: 59 in,
Backrest
Press Arm
Press
Note: The terms "right side" and "left side" are determined relative to a person sitting on a seat;
they do not correspond to right and left on the drawings in the manual.
4

ASSEMBLY
Make Assembly Easier for Yourself
Everything in this manual is designed to
ensure that the weight system can be assem-
bled successfully by anyone, Before begin-
ning assembly, make sure to read the
information on this page. This brief intro-
duction will save you much more time than
it takes to read it.
Assembly Requires Two Persons
For yourconvenience and safety, assemble the
weight system withthe help of another person.
Set Aside Enough Time
Due to the many features of the weightsystem, the
assembly process willrequire several hours. By
setting aside plentyof time and by deciding to
make the task enjoyable, assembly will go smoothly.
You may want to assemble the weight system over
a couple of evenings.
Select a Location for the Weight System
Because of itsweight and size, the weightsystem
should be assembled in the location where it will be
used. Make sure that there is enough room to walk
around the weight system as you assemble it.
How to Unpack the Box
To make assembly as easy as possible, we have
divided the assembly process into four stages. The
parts needed for each stage are found in individual
bags. Important: Wait until you begin each stage
to open the parts bag for that stage. Place all
parts of the weight system in a cleared area and
remove the packing materials. Do not dispose of
the packing materials until assembly is completed.
Make sure you have the following tools:
•Two adjustable wrenches
• One standard screwdriver
•One phillips screwdriver
• One rubbermallet
• You willalso need grease or petroleumjelly, a
small amount of soapy water, and clear tape or
masking tape.
Note: Assembly will be more convenient if you have
a socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
How to Identify Parts
To help you identifythe small parts used in assembly,
we have included aPART IDENTIFICATION CHART
in the center of this manual. Place the chart on the
floor and use itto easily identifyparts during each
assembly step. Note: Some small parts may have
been pre-attached. If a part is not in the parts
bag, check to see if it has been pre-attached.
How to Orient Parts
As you assemble the weight system, make sure all
pads are odented exactly as shown in the drawings.
Tightening Parts
Tighten all parts as you assemble them, unless
instructedto do otherwise.
Questions?
If you have questions after reading these assembly
instructions, please call 1-800-A-MY-HOME" (1-800-
469-4663).
The Four Stages of the Assembly Process
Frame Assembly--You will begin by assembling
the base and the updghtsthat form the skeleton of
the weightsystem.
Arm Assembly--During this stage you will
assemble the arms and the leg lever.
Cable Assembly--During this stage you will
attach the cables and pulleys that connectthe
arms to the weights.
Seat Assembly--During the final stage you will
assemble the seats and the backrests.
5

1. Before beginning assembly, make sure you
understand the information in the box on
page 5. See the PART IDENTIFICATION
CHART in the center of this manual for help
identifying small parts.
Insert four M8 x 75mm Carriage Bolts(69) up
through the Right Base (1). Note: It may be
helpful to place a piece of tape over each bolt
head to hold it in place.
2, Insert four M8 x 75mm Carriage Bolts (69) up
throughthe Left Base (25). Note: It may be help
ful to place a piece of tape over each bolt
head to hold it in place.
3. Attach the Right Base (1) to the LeftBase (25)
with two M8 x78mm Bolts(82), two M8 Washers
(98), and two M6 Nylon Locknuts (91). Do not
tighten the Locknuts yet.
4. Attach the Center Base (52) to the Right Base (1)
with two M8 x 78ram Bolts(82), two M8 Washers
(98), and an M8 Nylon Locknut (91). Do not
tighten the Bolts yet.
Attach the Center Base (52) to the Left Base
(25) in the same manner.
2
4
82
69
69
25
69
69
91
98 1 25 98
25
82
6

5.
6.
See drawing A. Attachthe Right Upright (2) to
the Right Base (1) with the two indicatedM8 x
75ram Carriage Bolts (69) and two M6 Nylon
Locknuts (91). Do not tighten the Locknuts yet.
See drawing B. Attach the Left Upright (26) to
the Left Base (25) with the two indicatedM8 x
75mm Carriage Bolts(69) and two M8 Nylon
Locknuts(91). Do not tighten the Locknuts yet.
Attach the Right Seat Frame (3) to the Right
Base (1) with the two indicated M8 x75mm
Carriage Bolts(69) and two M8 Nylon Locknuts
(91). Do not tighten the Locknuts yet.
Attach the Right Seat Frame (3) to the Right
Upright (2) with an M8 x 78mm Bolt(82), an M8 x
96mm Bolt (83), an M8 Washer (98), and an M8
Nylon Locknut (91). Do not tighten the Locknut
yet.
5A
91
91
B
25 91
69
6i
83 .-2
3 "i !
69
7

8.
Attach the Left Seat Frame (27) to the Left Base
(25) with the two indicated M8 x 75mm Carriage
Bolts (69) and two M8 Nylon Locknuts (91). Oo
not tighten the Locknuts yet.
Attach the Left Seat Frame (27) to the Left
Upright (26) with two M8 x 78ram Bolts (82), two
M8 Washers (98), and two M8 Nylon Locknuts
(91). Do not tighten the Locknuts yet.
Orient the Weight Guides (44) withthe indicated
holes closer to the bottom. Attach the Weight
Guides inside of the Center Base (52) with two
M8 x 78mm Bolts (82), four M8 Washers (98),
and two M8 Nylon Locknuts (91).
8
98 82
27
44... .44
Hole Hole
8

9. 9
Slide two Weight Bumpers (45) onto the Weight
Guides (44). Slide the eight Weights (55), with the
pin holes on the indicated side, onto the Weight
Guides.
Press the Weight Tube Bumper (46) intothe
Weight Tube (47). Insert the Weight Tube intothe
stack of Weights (55). Make sure the pin on the
Weight Tube sits in the groove in the top
Weight.
Grease the indicated holes in the Top Weight (56)
with an included grease pack. Slide the Top
Weight onto the Weight Guides (44).
10. Attach the Right Top Frame (5) to the Right
Upright (2) with two M8 x 78mm Bolts(82), two
M8 Washers (98), and two M8 Nylon Locknuts
(91). Do not tighten the Locknuts yet. Make
sure the Weight Guides (44) are behind the
Right Top Frame.
11. Attach a Weight Guide (44) to the Right Top
Frame (5) with an M8 x 78mm Bolt (82), two M8
Washers (98), and an M8 Nylon Locknut (91). Do
not tighten the Locknut yet.
Repeat this step with the other Weight Guide
(44).
10
11
5
56
82
91
5
82
9

12. Attach the LeftTop Frame (36) to the Right Top
Frame (5) with two M8 x 78mm Bolts(82), two
M8 Washers (98), two M8 x 83mm Bolts (112), a
Support Plate (31), and four M8 Nylon Locknuts
(91). Do not tighten the Locknuts yet.
13. Attach the Left Top Frame (36) to the Left Upright
(26) with two M8 x 83mm Bolts (112), a Support
Plate (31), and two M8 Nylon Locknuts (91). Do
not tighten the Locknuts yet.
14. Orient the ButterflyFrame (14) as shown. Attach
the Butterfly Frame to the Right Upright (2) with
two M8 x 72mm Bolts (85), two M8 Washers (98),
and two M8 Nylon Locknuts (91). Do not tighten
the Locknuts yet.
Attach the Butterfly Frame (14) to the Right Top
Frame (5) withtwo M8 x 78mm Bolts (82), two
M8 Washers (98), and two M8 Nylon Locknuts
(91).
Tighten the M8 Nylon Locknuts (91) used in
steps 3-14.
Arm Assembly
15. Wet the lowerend of the Left Butterfly Arm (6)
with soapy water. Slide aLarge Foam Pad (15)
onto the Left Butterfly Arm.
Grease an M10 x 90mm Bolt (74) and the indicat-
ed edges of two Arm Bushings (23) with a grease
packet. Attach the Left Butterfly Arm (6) to the
Butterfly Frame (14) with the Bolt (74), an M10
Large Washer (100), the two Arm Bushings, and
an M10 Nylon Locknut (90). Make sure the bolt
head fits inside of the hole in the Butterfly
Frame.
Repeat this step with the Right Butterfly Arm
(7).
12
91
31 112
36 98
5 91
13 112
91/' /:_
14 82
98
5
98
15
Grease
14 100-
90--_
Grease
10

16. Attach the Leg Bumper (59) to the Right Seat
Frame (3) with an M4 x 16mm Self-tapping Screw
(89) and an M4 Washer (96).
Grease an M10 x 75mm Bolt(60). Attach the Leg
Lever (4) tothe Right Seat Frame (3) with the
Boltand an M10 Nylon Locknut (90). Make sure
the "U"-rod is on the indicated side of the Leg
Lever. Do not overtighten the Locknut; the
Leg Lever must be able to pivot easily.
17, Grease an M10 x 108mm Bolt(72). Orientthe
Press Frame (29) as shown.Attach the Press
Frame to the LeftBase (25) with the Boltand an
M10 Nylon Locknut(90). Do not overtighten the
Locknut; the Press Frame must be able to
pivot easily.
18. Attach a Press Handle (32) to a Press Arm (30)
with an M10 x 65mm Bolt(77), two M10 Washers
(99), two M10 x 12mm Spacers (101), and an
M10 Nylon Locknut (90).
Attach a Press Arm Cap (34) to the Press Arm
(30) with an M10 x 45mm ButtonBolt (81) and an
M10 Large Washer (100).
Repeat this step with the other Press Arm
(30).
16
17
18
81
100
101 101 99
9O
77
Grease
32
3O
11

19. Attach aPress Arm (30) to the Press Frame (29)
with two M8 x69mm Bolt (86) and two M8 Nylon
Locknuts (91).
Repeat this step with the other Press Arm
(30).
20. Grease an M10 x 108mm Bolt(72). Attach the
Leg Press Frame (28) to the Left Base (25) with
the Bolt and an M10 Nylon Locknut (90). Do not
overtighten the Locknut; the Leg Press Frame
must be able to pivot easily.
21. Grease an M10 x 77mm Bolt (76). Attach the
Foot Plate (38) to the Leg Press Frame (28) with
the Bolt and an M10 Nylon Locknut (90). Make
sure the decal on the Foot Plate is right side
up. Do not overtighten the Locknut; the Foot
Plate must be able to pivot easily.
Cable Assembly
22. See the CABLE DIAGRAMS on pages 26 and
27 as you assemble the cables and to identify
the cables.
Locate the Press Cable (109). Attach the Cable
to the Leg Press Frame (28) with an M8 x 86mm
Shoulder Bolt(37) and an M8 Nylon Locknut (91).
19
21
22
86
90
j
72
90
Grease
38
37
12

23. Wrap the Press Cable (109) around a 90mm
Pulley (63). Attach the Pulley, two Half Finger
Guards (66), a Cable Trap (68), and an M10
Washer (99) to the Left Seat Frame (27) with an
M10 x 103ram Bolt (22) and an M10 Nylon
Locknut (90). Make sure the Cable Trap and the
Finger Guards are oriented as shown.
24. Wrap the Press Cable (109) around a "V"-pulley
(62). Attach the "V_-pulley,two Half Finger Guards
(66), and two M10 Washers (99) to the Leg Press
Frame (28) with an M10 x 115mm Bolt (71) and
an M10 Nylon Locknut (90). Make sure the
Finger Guards are oriented as shown.
25. Wrap the Press Cable (109) around a 90mm
Pulley (63). Attach the Pulley,two Half Finger
Guards (66), a Cable Trap (68), and an M10
Washer (99) to the Left Upright (26) with an M10
x 108mm Bolt (72) and an M1ONylon Locknut
(90). Make sure the Cable Trap and Finger
Guards are oriented as shown,
26. Wrap the Press Cable (109) around a 90mm
Pulley (63). Attach the Pulley, two Half Finger
Guards (66), a Cable Trap (68), and an M10
Washer (99) to the Press Frame (29) with an M10
x135mm Bolt(70). Make sure the Cable Trap
and Finger Guards are oriented as shown.
"90
71 _ '_"_99 99
66
66
13

27. Wrap the Press Cable (109) around a "W-pulley
(62). Attach the "W-pulley, two Half Finger Guards
(66), a Large Cable Trap (111), and an M10
Washer (99) inside the bracket on the Left
Upright (26) with an M10 x 65mm Bolt (77) and
an MIO Nylon Locknut (90). Make sure the
Cable Trap and Finger Guards are oriented as
shown.
28. Wrap the Press Cable (109) arounda90mm
Pulley (63). Attach the Pulley, two Half Finger
Guards (66), a Cable Trap (68), and an M10
Washer (99) to the Press Frame (29) with the
M10 x 135mm Bolt (70) used in step 26 and an
M10 Nylon Locknut (90). Make sure the Cable
Trap and Finger Guards are oriented as
shown.
29. Wrap the Press Cable (109) under a 90mm
Pulley (63). Attach the Pulley,two M10 Washers
(99), and two Half Finger Guards (66) insidethe
bracket on the LeftBase (25) with an M10 x
50mm Bolt(64) and an M10 Nylon Locknut(90).
Make sure the Finger Guards are oriented as
shown.
30. Wrap the Press Cable (109) over a 90mm Pulley
(63). Attach the Pulley and a Cable Trap (68) to
the Right Top Frame (5) with an M10 x 45mm
Bolt (80) and an M10 Nylon Lock,nut (90). Make
sure the Cable Trap is oriented to hold the
Cable in the groove of the Pulley.
27 66
i 99
, i
109
28
109
70
63 66 90
J
66
3O
80 68
_63 90
14

3!. Attach the end of the Press Cable (109) to a "U"-
bracket (50) with an M8 Washer (98) and an M8
Nylon Locknut (91). Note: Do not completely
tighten the Locknut; it should be tightened so
that only two threads of the Cable show past
the Locknut, as shown in the inset drawing.
32. Locate the Butterfly Cable (106). Grease an M8
x22mm Shoulder Bolt (39). Attach the Cable to
the Left ButterflyArm (6) withthe Boltand an M8
Nylon Locknut (91). Make sure the flat edge of
the Cable is against the Butterfly Arm.
33. Wrap the Butterfly Cable (106) over a "V"-pulley
(62). Attach the "V"-pulley, a Large Cable Trap
(111), an M10 Washer (99), and two Full Finger
Guards (104) to the Right Upright (2) with an M10
x 62mm Bolt (73) and an M10 Nylon Locknut
(9O).
34. Wrap the Butterfly Cable (106) under a 90mm
Pulley (63). Attach the Pulleyand two Half Finger
Guards (66) to the Double "U"-bracket (61) with
an M10 x 48mm Bolt (84) and an M10 Nylon
Locknut (90). Make sure the Finger Guards are
oriented as shown.
35. Wrap the Butterfly Cable (106) over a "V"-pulley
(62). Attach the "V"-pulley, a Large Cable Trap
(111), an M10 Washer (99), and two Full Finger
Guards (104) to the Right Upright (2) with an M10
x 62mm Bolt (73) and an M10 Nylon Locknut
(90).
32
Flat
Edge
90 106111
73
99 104
34
35
--_106
_63 90
84
15

36. Grease an M8 x22mm Shoulder Bolt(39). Attach
the ButterflyCable (106) to the Right Butterfly
Arm (7) with the Bolt and an M8 Nylon Locknut
(91). Make sure the flat edge of the Cable is
against the Butterfly Arm.
37. Locate the Short Cable (108). Attach the Cable
tothe M8 x 96mm Bolt(83) used in step 6 with
an M8 Washer (98), an M8 x 13ram Spacer (103),
and an M8 Nylon Locknut(91).
38. Wrap the Short Cable (108) over* a 90mm Pulley
(63). Attach the Pulley and two Half Finger
Guards (66) to the Double "U"-bracket (61) with
an M10 x 48mm Bolt (84) and an M10 Nylon
Locknut (90). Make sure the Finger Guards are
oriented as shown.
39. Attach the end of the Short Cable (108) to a "U"-
bracket (50) with an M8 Washer (98) and an M8
Nylon Locknut (91). Note: Do not completely
tighten the Locknut; it should be tightened so
that only two threads of the Cable show past
the Locknut, as shown in the inset drawing.
40. Locate the Weight Cable (110). Route the Cable
up throughthe Right Top Frame (5) and over a
90mm Pulley (63). Attach the Pulley insidethe
Top Frame with an M10 x 80mm Bolt (75), two
M10 Washers (99), two M10 x 19mm Spacers
(102), and an M10 Nylon Locknut (90).
36
37
2-_
Grease._
91...4
_0, [J
38 1
66
84
39
g-
A
40
--108
91
1o,
91
110
75 _. _f_'_ r
102 99
5162-\ 90
J
16

41. Route the Weight Cable (110) over a 90mm
Pulley (63) and down through the Right Top
Frame (5). Attach the Pulley insidethe Top Frame
with an M10 x 80mm Bolt (75), two M10 Washers
(99), two M10 x 19mm Spacers (102), and an
M10 Nylon Locknut (90).
42. Wrap the Weight Cable (110) under a 90mm
Pulley (63). Attach the Pulley, aCable Trap (68),
and two Half Finger Guards (66) at the second
holefrom the top ofthe two Pulley Plates (51)
with an M10 x 52ram Bolt (78) and an M10 Nylon
Locknut(90). Make sure the Cable Trap and
Finger Guards are oriented as shown.
43. Wrap the Weight Cable (110) over a 90mm Pulley
(63). Attach the Pulleyto the indicatedbracket on
the Right Top Frame (5) with an M10 x 45ram
Bolt (80) and an M10 Nylon Locknut (90).
44. Wrap the Weight Cable (110) over a90mm Pulley
(63). Attach the Pulley and a Cable Trap (68) to
the indicated bracket on the Right Top Frame (5)
with an M10 x 45mm Bolt (80) and an M10 Nylon
Locknut(90). Make sure the Cable Trap is ori-
ented to hold the Cable in the groove of the
Pulley.
45. Set the M12 Washer (33) on top ofthe Weight
Tube (47). Thread the M12 Nut (49) all the way
onto the Weight Cable (110).
Thread the Weight Cable (110) into the Weight
Tube (47) a couple of turns.
41
110
43 Bracket
5
44 A_ach _y!
75 102 99
90
5
63
51 f
51
110
•110
66
17

46. Locate the Ab Cable (107). Route the small ball
on the Cable throughthe Leg Lever (4) and the
Right Seat Frame (3). Make sure the Cable is
over the rod in the Seat Frame.
Attach a 90mm Pulley (63) insidethe Leg Lever
(4), over theAb Cable (107), with an M10 x
65ram Bolt (77), two M10 Washers (99), two M10
x 12ram Spacers (101), and an M10 Nylon
Locknut (90).
47. Attach a 90mm Pulley (63) insidethe Right Seat
Frame (3), over the Ab Cable (107), with an M10
x 45ram Bolt (80) and an M10 Nylon Locknut
(90).
48. Route the Ab Cable (107) throughthe Right
Upright (2) and under a 90mm Pulley (63). Attach
the Pulley and two Half Finger Guards (66) to the
Right Base (1) with an M10 x 50mm Bolt(64) and
an M10 Nylon Locknut (90). Make sure the
Finger Guards are oriented as shown,
49. Wrap the Ab Cable (107) over a 90mm Pulley
(63). Attach the Pulley, a Cable Trap (68), and
two Half Finger Guards (66) to the lower hole in
the indicated"U"-bracket (50) with an M10 x
52mm Bolt (78) and an M10 Nylon Locknut (90).
Make sure the Cable Trap and Finger Guards
are oriented as shown.
46
9O
Large
Ball
107
47
48
101
8O
63
50
66
.78
-63
77
18

50. Wrap the Ab Cable (107) under a 90mm Pulley
(63). Attach the Pulley, a Cable Trap (68), and
two Half Finger Guards (66) to the Right Base (1)
with an M10 x 50ram Bolt (64) and an M10 Nylon
Locknut(90). Make sure the Cable Trap and
Finger Guards are oriented as shown,
51. Wrap the Ab Cable (107) over a 90mm Pulley
(63). Attach the Pulley, a Cable Trap (68), and
two Half Finger Guards (66) at the second hole
from the bottom of the two Pulley Plates (51) with
an M10 x 52mm Bolt (78) and an M10 Nylon
Locknut(90). Make sure the Cable Trap and
Finger Guards are oriented as shown.
52. Wrap the Ab Cable (107) under a 90mm Pulley
(63). Attach the Pulley, a Cable Trap (68), and
two Half Finger Covers (66) to the Right Base (1)
with an M10 x 50mm Bolt (64) and an M10 Nylon
Locknut (90). Make sure the Cable Trap and
Finger Guards are oriented as shown.
53. Wrap the Ab Cable (107) over a 90mm Pulley
(63). Attach the Pulley, a Cable Trap (68), and
two Half Finger Guards (66) to the lower hole in
the indicated "U"-bracket (50) with an M10 x
52ram Bolt (78) and an M10 Nylon Locknut (90).
Make sure the Cable Trap and Finger Guards
are oriented as shown.
54. Wrap the Ab Cable (107) under a90ram Pulley
(63). Attach the Pulley,a Cable Trap (68) and two
Half Finger Guards (66) to the Right Base (1) with
an M10 x 50ram Bolt (64) and an M10 Nylon
Locknut (90). Make sure the Cable Trap and
Finger Guards are oriented as shown.
50
52
53
54
90 66
66
78\
9O
64
78_
107-
63
i51
"_,_j., 90
63 66
.64
68
19

55. Wrap the Ab Cable (107) over a 90mm Pulley
(63). Attach the Pulley and the two Quarter Finger
Guards (105) to the Right Upright (2) with an M10
x 108mm Bolt (72), an M10 Washer (99), and an
M10 Nylon Locknut(90). Make sure that the rod
is inserted through both Finger Guards and is
over the Cable.
56. Tighten the Weight Cable (110) intothe Weight
Tube (not shown) until all the slack is taken out of
the cables. Tighten the M12 Nut (49) on the
Weight Cable against the M12 Washer (33).
Seat Assembly
57. Attach a Backrest (9) to the Backrest Frame (53)
with four M6 x 16mm Screws (88).
Slide the Backrest Frame (53) into the Left
Upright (26). Engage the Knob (43) into the
Upright and Backrest Frame, and turn it clockwise
until it is tight.
58. Attach aSeat (8) to the Left Seat Frame (27) with
four M6 x 16ram Screws (88).
Repeat this step with the other Seat (8) and
the Right Seat Frame (not shown).
55
99 L,..,_r 63
1 _-'.J._72
56 33_ 11°
II
II
o
o
II
o
57 88 53
58
88
2O