Trinity TBFZ-2702 User manual

OWNER’S MANUAL
TRINITY MOBILE CLOSET ORGANIZER
Model # TBFZ-2702 / TBFPBR-2702
Everything in its place.®

© 2016 TRINITY - 800.985.5506
1

Your TRINITY Mobile Closet Organizer should include the following parts. Please inspect box
contents to ensure you have received all components.
If you are missing any parts, need assistance with assembly or have questions, please contact
TRINITY Customer Service: 800.985.5506 or [e-mail]. Parts can also be
requested online at www.trinityii.com (Help & More, Contact Us).
PARTS LIST
© 2016 TRINITY - 800.985.5506 2
MEDIUM SHELF (1)
A
SMALL SHELF (2)
B
TOP POLE (6)
End Cap and Pole Connector
are pre-installed
C
SIDEBAR
W/ HOOKS (1)
D
E
SLIP SLEEVE
(50) + (4) extra
F
I
BOTTOM POLE (6)
JK
MIDDLE POLE (6)
Pole Connector is
pre-installed
HANGING ROD (2)
G
HANGING BRACKET
& SCREW (4)
H
CASTER
(2) locking, (4) non-locking
LARGE SHELF (2)

ASSEMBLY INSTRUCTIONS
For easiest assembly, do not attach the TOP (D),
MIDDLE (E) and BOTTOM (F) POLES until
instructed. Once connected, these will be the posts
for the Organizer.
Note that each POLE (D+E+F) has slight horizontal
line indentations at 1” intervals. Each SLIP SLEEVE
(J) has raised horizontal lines inside designed to
lock them in place on the POLE (D+E+F).
On all (6) BOTTOM POLES (F) place 1 pair of SLIP
SLEEVES (J) at the lowest position, position closest
to the CASTERS (K). Please make sure the arrow
faces up and that the word “TOP” is right side up.
Slide the pair of SLIP SLEEVES (J) until you hear a
click to confirm the pair is locked onto the BOTTOM
POLE (F). DO NOT place more than one pair on
each POLE (F) at a time.
Screw each CASTER (K) into the bottom of
each BOTTOM POLE (F). Turn clockwise to
screw in place.
Tighten the CASTER (K) completely using
the included Caster Wrench. Failure to
do as instructed could result in the caster
stem breaking.
STEP 1
STEP 2
F (6) K (6)
F
K
J
J (12)
© 2016 TRINITY - 800.985.5506
3
* Note: There will be a very small gap in-between the SLIP SLEEVES (J)—this is normal.

ASSEMBLY INSTRUCTIONS
Place the LARGE SHELF (A) on its side and
slide the (6) BOTTOM POLES (F) through the
holes in the LARGE SHELF (A). Make sure
that the LARGE SHELF (A) corner cylinders
are positioned over the SLIP SLEEVES (J).
Stand the unit upright.
*Note: The level side of the LARGE SHELF (A)
is the TOP side (the TRINITY logo on the
corner cylinders should be right-side up.)
**Use a rubber mallet, if needed, to secure the
LARGE SHELF (A).
STEP 3
A (1)
A
© 2016 TRINITY - 800.985.5506 4
***For convenience, place BOTTOM POLES (F) with Locking Casters on the long side of the
shelf if the organizer will be pushed against a wall OR if the organizer is frequently rolled around
like a cart, place BOTTOM POLES (F) with Locking Casters on the side being pushed or pulled.
Screw the MIDDLE POLES (E) into the
BOTTOM POLES (F).
STEP 4
E (6)
E

B
C
3
1
2
J
ASSEMBLY INSTRUCTIONS
© 2016 TRINITY - 800.985.5506
5
Screw the TOP POLES (D) into the MIDDLE
POLES (E).
STEP 5
D (6)
D
Decide the position of MEDIUM SHELF (B) and
SMALL SHELVES (C) that will best fit your needs.
Starting with the lowest desired SHELF position,
Place 1 pair of SLIP SLEEVES (J) on each of the (4)
POLES for that SHELF. Please make sure the
arrow faces up and that the word “TOP” is right side
up. Make sure that the heights are identical for each
POLE.
Repeat Step 6 to install the next lowest SHELF as
desired.
If you are installing the MEDIUM SHELF (B) above
the SMALL SHELF (C), please make sure that you
place the SLIP SLEEVES (J) at least 4 indentations
above the SMALL SHELF (C) so that the HANGING
BAR (G+H) can fit properly.
*Use a rubber mallet, if needed, to secure the
SHELVES (A+B+C).
STEP 6
J (24)B (1) C (2)

ASSEMBLY INSTRUCTIONS
© 2016 TRINITY - 800.985.5506 6
Place 1 pair of SLIP SLEEVES (J) at the top
of each POLE. Please make sure the arrow
faces up and that the word “TOP” is right
side up.
Lower LARGE SHELF (A) over the POLES
so that the corner cylinders of the LARGE
SHELF (A) are positioned over the SLIP
SLEEVES (J).
*Use a rubber mallet, if needed, to secure
the SHELVES (A+B+C).
STEP 7
A (1) J (12)
J
A
Hang the HANGING BRACKET (H) on both ends of the
MEDIUM SHELF (B) and the LARGE SHELF (A) as shown.
Fasten HANGING SCREW (H) through HANGING
BRACKET (H) to HANGING ROD (G). Do this for both
HANGING RODS (G).
STEP 8
H (4)
G (2)
G
H

ASSEMBLY INSTRUCTIONS
© 2016 TRINITY - 800.985.5506
7
Locate the desired position and place a pair
SLIP SLEEVES (J) onto the pole.
Slide the SIDEBAR W/ HOOKS (I) down, over
the SLIP SLEEVES (J).
STEP 9
J (2)I (1)
J
I

© 2016 TRINITY - 800.985.5506 8
SERVICE PARTS LIST –TBFPBR-2702 Bronze Color
Part Number Description 8) Part Number Description
1) XBK-01-012-2543 Slip Sleeve 9) XXX-97-002-0001 Wrench
2) PBR-04-006-2475 Top Pole 10) PBR-03-007-2814 Medium Shelf
3) ZSV-01-013-2523 Pole Connector 11) PBR-02-007-0004 Sidebar w/ Hooks
4) PBR-04-007-2500 Middle Pole 12) PBR-13-006-2800 Hanging Rod
5) PBR-03-007-1414 Small Shelf 13) XBK-01-024-0627 Hanger Screw
6) PBR-04-008-2425 Bottom Pole 14) PBR-02-010-0001 Hanger
7) ZSV-99-008-3010 Locking Caster 15) PBR-03-007-4114 Large Shelf
8) ZSV-99-007-3010 Non-locking Caster
TRINITY Customer Service provides the following replacement parts:
5
2
15
11
1
4
8
6
7
3
9
12
13
10
14

© 2016 TRINITY - 800.985.5506
9
SERVICE PARTS LIST –TBFZ-2702 Chrome Color
TRINITY Customer Service provides the following replacement parts:
Part Number Description Part Number Description
1) XBK-01-011-2543 Slip Sleeve 9) XXX-97-002-0001 Wrench
2) ZSV-04-006-2475 Top Pole 10) ZSV-03-007-2814 Medium Shelf
3) ZSV-01-013-2523 Pole Connector 11) ZSV-02-007-0004 Sidebar w/ Hooks
4) ZSV-04-007-2500 Middle Pole 12) ZSV-13-006-2800 Hanging Rod
5) ZSV-03-007-1414 Small Shelf 13) XBK-01-024-0627 Hanger Screw
6) ZSV-04-008-2425 Bottom Pole 13) ZSV-02-010-0001 Hanger
7) ZSV-99-008-3010 Locking Caster 14) ZSV-03-007-4114 Large Shelf
8) ZSV-99-007-3010 Non-locking Caster
5
2
15
11
1
4
8
6
7
3
9
12
13
10
14