Tyco Electronics Pro-Crimper III User manual

Instruction Sheet
PRO-CRIMPER* III Hand Crimping
Tool Assembly 58583-1 with 408-4165
L C B
1 of 5
E 2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. ther products, logos, and company names used are the property of their respective owners.
T LING ASSISTANCE CENTER 1-800-722-1111
PR DUCT INF RMATI N1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
12 MAY 09 Rev A
Die Assembly 58583-2
PROPER USE GUIDELINES
CumulativeTraumaDisorderscanresultfromtheprolongeduseof manuallypoweredhandtools.Handtoolsareintendedforoccasionaluseandlowvolume
applications. A wide selection of powered application equipment for extended-use, production operations is available.
Stationary
Jaw
Back of Tool
(Wire Side)
PR -CRIMPER III Hand
Crimping Tool Frame
354940-1 (408-9930)
Pivot
Pin
Stationary
Handle
Moving
Handle
Ratchet
Adjustment
Wheel
Moving
Jaw
Die Assembly
58583-2
Front of Tool
(Locator Side)
Locator Assembly
(Supplied with Die
Assembly)
The PR -CRIMPER III Hand Crimping Tool is a Commercial" grade tool and
is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 application specification, but may not comply with other
feature parameters of the specification. Tyco Electronics offers a variety of
tools to satisfy your performance requirements. For additional information,
contact the Tooling Assistance Center at 1-800-722-1111.
C
ire
TE
Die Assembly TE
Locator Assembly
{
Contact
Family
}
Size
(mm2)
Insulation
Diameter
(mm [Inches])
Strip Length
(mm [Inches])
58583-2 58515-1 SUPERSEAL*
1.5 Series Contacts 0.5-1.5 1.70-2.40 [.067-.094] 3.00-3.50 [.118-.138]
{ Supplied with die assembly, also available separately.
} Contact the Tooling Assistance Center or Product Information Center
(below) for specific contact part numbers.
Figure 1
1. INTRODUCTION
PRO–CRIMPER III Hand Crimping Tool Assembly
58583–1 consists of Die Assembly 58583–2 and
PRO–CRIMPER III Hand Crimping Tool Frame
354940–1.
The die assembly consists of crimping dies and a
locator assembly.
Read these instructions thoroughly before crimping
any contacts.
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
NOTE
i

408-4165
PRO-CRIMPER III Han Crimping Tool Assembly 58583-1
Rev A2 of 5 Tyco Electro ics Corporatio
Figure 2
Nut
Locator
Chamfer
Wire
Crimper
Offset
Wire A vil I sulatio
A vil Chamfer Die Retai i g
Screws
Die Retai i g
Pi s
Tool Frame
Locator
Assembly
I sulatio
Crimper
2. DESCRIPTION (Figures 1 a d 2)
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with three
crimping chambers. The die assembly features a wire
anvil, an insulation anvil, a wire crimper, and an
insulation crimper.
Attached to the outside of the frame is a locator
assembly, which contains a locator, a spring retainer,
and a contact support.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame. A
nut is used on the upper die retaining screw to hold
the locator assembly in place.
3. INSTALLATION AND REMOVAL OF DIE ASSEMBLY
AND LOCATOR ASSEMBLY
(Figure 2)
1. Open the tool handles and remove the two die
retaining screws from the tool jaws.
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do
not
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two die retaining pins.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure
that the anvils and crimpers align properly.
Continue closing the tool handles until the ratchet
in the tool frame has engaged sufficiently to hold
the anvils and crimpers in place, then tighten both
die retaining screws.
9. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
10. Place the nut onto the end of the long screw
and tighten the nut enough to hold the locator
assembly in place, while still allowing the locator to
slide up and down.
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator

408-4165
PRO-CRIMPER III Hand Cr mp ng Tool Assembly 58583-1
3 of 5Rev A
Tyco Elect onics Co po ation
assembly, the two die retaining screws, and the
four die retaining pins, and slide the anvils and
crimpers out of the tool jaws.
4. CONTACT SUPPORT ADJUSTMENT (Figu e 3)
The contact support s preset pr or to sh pment,
but m nor adjustment may be necessary.
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator
assembly.
The ratchet has detents that create aud ble cl cks
as the tool handles are closed.
3. Place a contact with wire into the proper nest
and close the tool handles until the ratchet reaches
the sixth click, or until the contact support touches
the contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
5. Move the contact support as required to
eliminate the bending of the contact.
6. Tighten the nut and close the handles until the
ratchet releases.
7. Remove and inspect the contact.
8. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat
the adjustment procedure.
5. CRIMPING PROCEDURE
Th s tool s prov ded w th a cr mp adjustment
feature. Int ally, the cr mp he ght should be
ver f ed as spec f ed n F gure 4. Refer to
Sect on 6, CRIMP HEIGHT INSPECTION, and
Sect on 7, CRIMP HEIGHT ADJUSTMENT, to
ver fy cr mp he ght before us ng the tool to cr mp
des red contacts and w re s zes.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Assemble
applicable wire seal onto wire according to the
instructions packaged with the contact. Strip the wire
to the length indicated in Figure 1, taking care not to
nick or cut wire strands. Select an applicable contact
and identify the appropriate crimping chamber
according to the wire size markings on the tool. Refer
to Figure 3 and proceed as follows:
1. Hold the tool so that the back (wire side) is
facing you. Squeeze tool handles together and
allow them to open fully.
2. Holding the contact by the mating end, insert the
contact—insulation barrel first—through the front of
the tool and into the appropriate crimping chamber.
3. Position the contact so that the mating end of
the contact is on the locator side of the tool, and so
that the open “U” of the wire and insulation barrels
face the top of the tool. Place the contact up into
the nest so that the movable locator drops into the
slot in the contact. Refer to Figure 3. Butt the front
end of the wire barrel against the movable locator.
Figure 3
Adjustment
Sc ew fo
Contact
Suppo t
Contact
Suppo t Locato
Back of Tool
(Wi e Side)
Wi e
Contact
(Typ)
Locato in
Wi e Stop Slot Wi e
Inse ted
to Stop
St ip
Length
Wi e
Seal
Wi e
Seal
NOTE
i
NOTE
i
NOTE
i

408-4165
PRO-CRIMPER III Hand Crimping Tool Assembly 58583-1
R v A4 of 5 Tyco El ctronics Corporation
Make sure t at bot sides of t e insulation barrel
are started evenly into t e crimping c amber.
Do NOT attempt to crimp an improperly
positioned contact.
4. Hold the contact in position and squeeze the
tool handles together until ratchet engages
sufficiently to hold the contact in position. Do NOT
deform insulation barrel or wire barrel.
5. Insert stripped wire (with wire seal) into contact
insulation and wire barrels until it is butted against
the wire stop, as shown in Figure 3.
6. Holding the wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open and remove crimped contact.
T e crimped contact may stick in t e crimping
area, but t e contact can be easily removed by
pus ing downward on t e top of t e locator (see
Figure 3).
7. Check the contact crimp height as described in
Section 6, CRIMP HEIGHT INSPECTION. If
necessary, adjust the crimp height as described in
Section 7, CRIMP HEIGHT ADJUSTMENT.
6. CRIMP HEIGHT INSPECTION
This inspection requires the use of a micrometer with
a modified anvil.
Tyco Electronics does not manufacture or market
t ese gages. However, TE recommends t e
modified micrometer (Crimp Heig t Comparator
RS-1019-5LP) or t e digital Mitutoyo
micrometer.
Proceed as follows:
1. Refer to Figure 4 and select a wire (maximum
size) for each crimping chamber listed.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height as shown in Figure 4. If the
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
CRIMP HEIGHT ADJUSTMENT.
7. RATCHET (Crimp Height) ADJUSTMENT (Figur 5)
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the locator side of the tool.
A"
+0.05
[+.002]
Position Point
on C nt r of
Wir Barr l
Opposit S am
Modifi d
Anvil
ire Size
(mm2)Crimping Chamber ( ire Size Marking) Crimp Height Dimension a"
0.5 0.5 1.12 [.044]
1.0 1.0 1.30 [.051]
1.5 1.5 1.45 [.057]
Figure 4
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher–numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower–numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the dimension is acceptable, secure the
lockscrew. If the dimension is unacceptable,
continue to adjust the ratchet, and again measure
a sample crimp.
Figure 5
Scr wdriv r
Ratch t
Adjustm nt
Wh l
Lockscr w
(Typ)
CAUTION
!
NOTE
i
NOTE
i

408-4165
PRO-CRIMPER III Hand Crimpin Tool Assembly 58583-1
5 of 5Rev A
Tyco Electronics Corporation
8. MAINTENANCE
Ensure that the tool and dies are clean by wiping
them with a clean, soft cloth. Remove any debris with
a clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
closed to prevent objects from becoming lodged in
the crimping dies, and store in a clean, dry area.
9. VISUAL INSPECTION
The crimping dies should be inspected on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimping chambers for
flattened, chipped, worn, or broken areas. If damage
or abnormal wear is evident, the tool must be
replaced. See Section 10, REPLACEMENT.
10. REPLACEMENT
Customer–replaceable parts are shown in Figure 1.
Available separately, PRO–CRIMPER III Hand
Crimping Tool Repair Kit 679221–1 includes a
replacement nut and a variety of pins, rings, screws,
and springs.
If the dies are damaged or worn excessively, they
must be replaced.
Order the repair kit and replaceable parts through
your Tyco Electronics representative, or call
1–800–526–5142, or send a facsimile of your
purchase order to 1–717–986–7605, or write to:
CUSTOMER SERVICE (38–35)
TYCO ELECTRONICS
PO BOX 3608
HARRISBURG PA 17105–3608
11.REVISION SUMMARY
Since the previous release of this instruction sheet:
S The TE logo was applied;
S The PRO–CRIMPER II hand tool became the
PRO–CRIMPER III hand tool; and
S The format was updated to the current
corporate requirements.