Tyco Kantech kt-mod-inp16 User manual

Unauthorized use is strictly prohibited.

Tel.: 1 (450) 444 2030 • Toll Free: 1-888-222-1560 • www.kantech.com DN1776-1911

KT-MOD-INP16

KT-400 Expansion Module 16-Zone Input with SPI Cable Install Sheet

1. Introduction

The KT-MOD-INP16 is an input module that adds up to 16 zones

to the KT-400 controller. The module supports daisy chaining;

you can interconnect up to 15 KT-MOD-INP16 modules for a total

of 240 external inputs per KT-400. Adding the 16 onboard inputs

of the KT-400 gives a total of 256 inputs per KT-400. Combining

input and output expansion modules gives the flexibility to

connect up to 256 inputs and 256 outputs.

Note 1: The KT-400 SPI port maximum current draw, when the

12V AUX terminals are not used, is 500 mA.

Note 2: External power supply (12 VDC, 2 Amps) is required

when the total current draw exceeds 500mA on the SPI Port.

2. Specifications

Maximum Current Draw: up to 40 mA per module

Supports single end-of-line (5.6 KΩ) resistor, double end-of-

line resistor and no end-of-line (DRY) zone loops

Supports Normally Closed (NC) and Normally Open (NO)

contacts

The C (Common) terminal is GND

Input change with a debouncing of 500 ms (Slow) or

150 ms (Fast)

Report conditions per input: SECURE or ALARM in single

end-of-line and no end-of-line zone loops, and 2 additional

conditions TAMPER and TROUBLE in double end-of-line

zone loops

Can be used for contact or elevator input

Cannot be connected to output modules KT-MOD-REL8 and

KT-MOD-OUT16 through SPI OUT, only through its SPI EXP

expansion port

Operating Temperature: -10C to +55C, 0C to 49C for UL

Listed product

Maximum Humidity: 93% (non condensing), 0 to 85% (non

condensing) for UL Listed product

IP Class 3X, IK Rating 04 (when mounted in a Kantech

cabinet). IP and IK rating not evaluated by Underwriters

Laboratories.

3. Installing the KT-MOD-INP16 Module

3.1. Unpacking

The KT-MOD-INP16 package includes the following parts:

One (1) KT-MOD-INP16 module, 14 cm x 8 cm (5.7 in x 3.25

in)

One (1) SPI cable with 1 SPI connector, 41 cm (16 in)

16x 5.6K Ohms ½ Watt Resistor

Four (4) plastic standoffs

Two (2) installation sheets, English and French

3.2. Mounting

The KT-MOD-INP16 can be installed inside a compatible cabinet

(KT-MOD-CAB or KT-400) or mounted in a dry and secure

location at less than 1 m (3 ft) from the KT-400.

1. Press the four (4) plastic standoffs through the mounting

holes of the cabinet,

2. Secure the cabinet to the wall in the desired location. Use

appropriate wall anchors when securing the cabinet to

drywall, plaster, concrete, brick or other surfaces.

3. Press the module into the plastic standoffs to secure the

module to the cabinet.

3.3. SPI Wiring

Perform the following steps to complete wiring:

Note 1: Before beginning to wire the unit, ensure that all power

(AC transformer and battery) is disconnected from the KT-400.

Note 2:If you are combining input and output modules through

the SPI EXP expansion port of the KT-MOD-INP16, the input

module must be the 1st module connected to the KT-400 SPI

Port.

1. Connect the 6-pin SPI connector to the KT-400 SPI port or to

the SPI OUT of the previous KT-MOD-INP16 module.

2. Connect the six SPI wires (blue (BLU), white (WHT), green

(GRN), yellow (YEL), black (BLK) and red (RED)) to the SPI

IN (TB1) terminals.

3. You can use the SPI EXP of the 1st KT-MOD-INP16 to start a

group of output modules (KT-MOD-REL8 and KT-MOD-

OUT16 only).

4. Connect the 6-pin SPI connector from the SPI OUT to the

next KT-MOD-INP16 module.

5. Complete all zone wiring to the zone input terminals (Z1-Z16).

Unauthorized use is strictly prohibited.

Tel.: 1 (450) 444 2030 • Toll Free: 1-888-222-1560 • www.kantech.com DN1776-1911

KT-MOD-INP16

KT-400 Expansion Module 16-Zone Input with SPI Cable Install Sheet

3.4. Check the power jumper JP5 position. Put it on EXT if you

need external power or INT if no external power is required.

Note: In double end-of-line resistor configuration (JP4 ON position),

only 8 zone inputs (Z1 through Z8) are operational. Z9 through Z16

are operational only in single and no end-of-line configurations (JP4

OFF position). This configuration is available from firmware version

1.03 and later.

Interconnection is still limited to 15 KT-MOD-INP16 modules for a total

of 120 external double end-of-line inputs per KT-400.

4. Configurations with Jumpers

There are 4 jumpers available to configure the KT-MOD-INP16.

The jumper settings apply to ALL inputs at the same time.

DRY (no end-of-line resistor): In a simple NC dry contact

configuration, the secure state is given when a short is detected.

The voltage becomes lower than the Level 1 threshold value

(1.1V).

The alarm state is given when the input is open. The voltage

becomes higher than the Level 2 threshold value (3.75V). If the

alarm switch is programmed as NO device, the alarm state will

be given when the input is shorted.

EOL (single end-of-line resistor): For NC device, the secure

state is given when a single resistor is detected. The voltage

becomes lower than the Level 3 threshold value (2.9V) and

higher than the Level 2 threshold value (2.25V).

The alarm state is given when the input is open or short. The

voltage becomes higher than the Level 4 threshold value (3.75V)

or lowers than the Level 1 threshold value (1.1V). If the alarm

switch is programmed as NO device, the alarm state will be given

when a single resistor is detected.

DEOL (double end-of-line resistor): Both Alarm and Tamper

switches always operate as NC devices. The secure state is

given when a single resistor is detected. Corresponding digital

reading is lower than the Level 3 threshold value (2.9V) and

higher than the Level 2 threshold value (2.25V). The alarm state

is given when double resistors in series are detected.

Corresponding digital reading is lower than the Level 4 threshold

value (3.75V) and higher than the Level 3 threshold value (2.9V).

The trouble state is given when the input is shorted.

Corresponding digital reading is lower than the Level 1 threshold

value (1.1V). The tamper state is given when the input is left

open. Corresponding digital reading is higher than the Level 4

threshold value (3.75V).

Double End-of-Line resistor functionality not evaluated by

Underwriters Laboratories.

5. Applying Power

After all wiring is completed, connect the 16 VAC to the KT-400.

Connect the battery leads to the battery, and then apply power to

the AC transformer.

Note: Do not connect power until all wiring is complete.

This module provides access point control (5) as per EN50133-1.

Certified by Telefication under the requirements of EN50133-1 and

EN50130-5 Class II.

Unauthorized use is strictly prohibited.

Tel.: 1 (450) 444 2030 • Toll Free: 1-888-222-1560 • www.kantech.com DN1776-1911

KT-MOD-INP16

KT-400 Expansion Module 16-Zone Input with SPI Cable Install Sheet

Terminal Connections

Module no.: _______________________________________________________________________________________

Date of installation: ________________________________________________________________________________

KT-400 Name: _____________________________________________________________________________________

KT-400 SITE NAME: ________________________________________________________________________________

KT-400 Serial Number:______________________________________________________________________________

AUX: ____________________________________________________________________________________________

SPI BUS (FROM): __________________________________________________________________________________

SPI BUS (TO): _____________________________________________________________________________________

Z1: Z9: __________________________________________

Z2: Z10: _________________________________________

Z3: Z11: _________________________________________

Z4: Z12: _________________________________________

Z5: Z13: _________________________________________

Z6: Z14: _________________________________________

Z7: Z15: _________________________________________

Z8: Z16: _________________________________________

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Kantech could void your authority to use this equipment.

This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufacturer’s instructions, may cause interference to

radio and television reception. It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart “B” of Part 15 of FCC Rules,

which are designed to provide reasonable protection against such interference in any residential installation. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause interference to television or radio reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Re-orient the receiving antenna

• Relocate the alarm control with respect to the receiver

• Move the alarm control away from the receiver

• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the FCC

helpful: “How to Identify and Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington, D.C.20402, Stock # 004-

000-00345-4.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received including interference that may cause undesired operation.

This class B digital apparatus complies with Canadian ICES-003.

The KT-MOD-INP16 is also compliant with EN55022: Class B.

UL 294 Performance Levels

Destructive Attack: I Line Security: I

Endurance: IV Standby Power: I*

*Standby Power Level IV when powered by KT-400.

Unauthorized use is strictly prohibited.

Tel.: 1 (450) 444 2030 • Toll Free: 1-888-222-1560 • www.kantech.com DN1776-1911

KT-MOD-INP16

KT-400 Expansion Module 16-Zone Input with SPI Cable Install Sheet

TYCO INTERNATIONAL LTD

END-USER LICENSE AGREEMENT

FOR KANTECH Software Provided with or without products or components

IMPORTANT - READ CAREFULLY

KANTECH Software purchased with or without Products and Components is copyrighted and is purchased under the following license terms:

•This End-User License Agreement (“EULA”) is a legal agreement between You (the company, individual or entity who acquired the Software and any related Hardware) and KANTECH, the

manufacturer of the integrated security systems and the developer of the software and any related products or components (“HARDWARE”) which You acquired.

•If the KANTECH software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is intended to be accompanied by HARDWARE, and is NOT accompanied by new HARDWARE, You may not

use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include associated media, printed materials, and “online” or electronic

documentation.

•Any software provided along with the SOFTWARE PRODUCT that is associated with a separate end-user license agreement is licensed to You under the terms of that license agreement.

•By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be bound by the terms of this EULA, even if this EULA is

deemed to be a modification of any previous arrangement or contract. If You do not agree to the terms of this EULA, KANTECH is unwilling to license the SOFTWARE PRODUCT to You, and

You have no right to use it.

SOFTWARE PRODUCT LICENSE

a The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The SOFTWARE PRODUCT is

licensed, not sold.

1 GRANT OF LICENSE - This EULA grants You the following rights:

a Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed.

b Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from different computers, including a workstation,

terminal or other digital electronic device (“Device”). In other words, if You have several workstations, You will have to acquire a license for each workstation where the SOFTWARE will be

used.

c Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per license installed at any given time. You may use the back-up copy

solely for archival purposes. Except as expressly provided in this EULA, You may not otherwise make copies of the SOFTWARE PRODUCT, including the printed materials accompanying

the SOFTWARE.

2 DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS

a Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT, except and only to the

extent that such activity is expressly permitted by applicable law notwithstanding this limitation. You may not make any changes or modifications to the Software, without the written

permission of an officer of KANTECH. You may not remove any proprietary notices, marks or labels from the Software Product. You shall institute reasonable measures to ensure

compliance with the terms and conditions of this EULA.

b Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use on more than one HARDWARE unit.

c Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT is licensed with the HARDWARE as a single integrated product.

In this case, the SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in this EULA.

dRental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a server or web site.

eSoftware Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer of the HARDWARE, provided You retain no copies, You

transfer all of the SOFTWARE PRODUCT (including all component parts, the media and printed materials, any upgrades and this EULA), and provided the recipient agrees to the terms of

this EULA. If the SOFTWARE PRODUCT is an upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.

fTermination - Without prejudice to any other rights, KANTECH may terminate this EULA if You fail to comply with the terms and conditions of this EULA. In such event, You must destroy all

copies of the SOFTWARE PRODUCT and all of its component parts.

g Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of KANTECH or its suppliers.

3 COPYRIGHT

All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the

accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are owned by KANTECH or its suppliers. You may not copy the printed materials accompanying the SOFTWARE

PRODUCT. All title and intellectual property rights in and to the content, which may be accessed through use of the SOFTWARE PRODUCT, are the property of the respective content owner and may

be protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not expressly granted under this EULA are reserved

by KANTECH and its suppliers.

4 EXPORT RESTRICTIONS

You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject to US export restrictions.

5 CHOICE OF LAW

This Software License Agreement is governed by the laws of the State of New York.

6 LIMITED WARRANTY

a NO WARRANTY

KANTECH PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. KANTECH DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT

OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.

b CHANGES IN OPERATING ENVIRONMENT

KANTECH shall not be responsible for problems caused by changes in the operating characteristics of the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT

with non-KANTECH SOFTWARE or HARDWARE PRODUCTS.

c LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK

IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT D IN THIS LICENSE AGREEMENT, KANTECH'S ENTIRE LIABILITY UNDER ANY PROVISION OF

THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE US

DOLLARS (USD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES,

THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

d DISCLAIMER OF WARRANTIES

THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF KANTECH.

KANTECH MAKES NO OTHER WARRANTIES. KANTECH NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR

TO CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT.

e EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY

UNDER NO CIRCUMSTANCES SHALL KANTECH BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF

WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF

PROFITS, LOSS OF THE SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES

OR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY.

WARNING: KANTECH recommends that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or