U-Line H-1393 User manual

PAGE 1 OF 8 0713 IH-1393
H-1393
H-3639
SIX TIER
LOCKER
1-800-295-5510
uline.com
π
TOOLS NEEDED
11/32" Nut Driver
(included)
CAUTION! Some parts may have sharp
edges. Take care when handling various
pieces to avoid injury. For your safety, wear
work gloves when assembling.
Para Español, vea páginas 5-8.

PAGE 2 OF 8 0713 IH-1393
PARTS
9
11
10
8
#DESCRIPTION QTY.
1Back 3
2Left Side 2
3 Rear Leg 4
4Shelf 15
5Top/Bottom Shelves 6
6Right Side 2
7 Door Frame Assembly 3
#DESCRIPTION QTY.
8Locker Door 18
9 Number Plate & Clear Label Cover 18
10 Push Plug 36
11 Finger Pull 18
PRIMARY ASSEMBLY
NO ASSEMBLY REQUIRED
8
7
2
3
6
5
5
1
4

PAGE 3 OF 8 0713 IH-1393
NOTE: Do not tighten bolts until
unit is completely assembled.
1. Locate and separate the left and righthand sides.
Identify the top of each panel. The top of each
panel has three holes instead of one.
2. Place back (1) on a protected flat surface so that
the flanges face upward.
3. Bolt left side (2) to the back so that side flange fits
around back (use 7 bolts and nuts - nuts to the
inside). Do not use bottom two holes; these will be
used for attaching legs in step 7. (See Figure 1)
4. Next bolt top, bottom (5) and shelves (4) to back
and left side panel (use 4 bolts and nuts each).
Next bolt an intermediate side and back panel
to the flange on the back of the first locker in 7
places. Next attach a top, bottom and intermediate
top to the first intermediate side and back. These
will share bolts with the parts on either side of them
as shown in detail view. Next attach remaining
intermediate side and back to flange of second
back. Attach remaining top, bottom and shelves to
the intermediate side. (See Figure 2)
5. Bolt right side (6) to the back so that side flange
fits around back. Attach side to top, bottom and
shelves. (See Figure 3)
6. Insert legs (3) into the corner between the bottom
and the side. Bolt the leg to the side using two bolts
and nuts per leg. (See Figure 4)
7. Place door and frame assemblies (7& 8) over the
locker body. Make certain that body sides are
inside frames, not between the frames. Attach top
to frame header and the bottom to frame sill (one
bolt each). (See Figure 5)
8. Stand unit upright and place in desired location.
Remove temporary bolts in frames and bolt to any
adjacent units together through frames.
ASSEMBLY INSTRUCTIONS
1
2
Top
Bottom
Figure 1
2
6
4
5
1
6
Figure 2
Figure 3

PAGE 4 OF 8 0713 IH-1393
NOTE: If the temporary bolts are not removed
before the frames are joined side by side, the
frames will have a 1/8" gap between them.
JOINING UNITS TOGETHER
1. If joining a 3-wide unit beside another unit,
temporarily install a bolt and nut into the third and
sixth holes down from the top of the outer frame(s)
that will be joined to the adjacent locker frame(s).
(See Figure 6) The center locker frame can be
bolted complete. If locker is just a stand alone
3-wide unit, finish attaching the frames using 38
bolts and nuts. Check and tighten all permanent
bolts.
SECURING UNITS
1. Anchor units to wall or floor. Units are not intended
to stand free and may topple if not secured. (Units
standing back to back should be bolted together.)
CAUTION: Care must be taken to assure
that lockers are set plumb and true before
anchoring.
2. If units are not pre-numbered, optional number
plate and plastic cover (9) may be attached with
two push plugs (10).
3
Figure 4
7
8
ASSEMBLY CONTINUED
Figure 5
Figure 6
π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA
1-800-295-5510
uline.com

PAGE 5 OF 8 0713 IH-1393
πH-1393
H-3639 01-800-295-5510
uline.mx
LOCKER DE
SEIS PUERTAS
REQUIERE HERRAMIENTAS
Desarmador para Tuercas
d e 11/32 "(inluido)
¡PRECAUCIÓN! Algunas partes pueden tener
bordes filosos. Debe tener cuidado cuando
manipule varias piezas para evitar lesiones.
Por su seguridad, utilice guantes de trabajo
cuando ensamble.