U-Line H-2449 User manual

0313 IH-2449PAGE 1 OF 3
GARMENT STORAGE
CENTER WITH SHELVES
H-2449
PARTS
ASSEMBLY
Connector x 6 36 x 18" Shelf x 1
Tall Post Top x 6 Tall Post Bottom x 6
18 x 18" Shelf x 12
Shelf Support (52 Sets)
Garment Rod x 1
Self-leveler x 8 Garment Rod Hanger x 2
Short Post x 2
Figure 1
Figure 2
POST ASSEMBLY
1. Connect tall post tops and tall post bottoms to each
other by screwing them together. (See Figure 1)
NOTE: Tall post tops have a black plastic cap in
the top of the post.
TO INSTALL SELF-LEVELERS
1. Make sure post is positioned as shown. (See Figure 2)
2. Insert self-leveler into open end of post. Tap on
ground to slide self-leveler into post.
3. Repeat step 2 for all other posts.
TO INSTALL OPTIONAL CASTERS
1. Make sure post is positioned as shown. (See Figure 3)
2. Engage the wheel brakes to keep casters from
rolling during assembly. Use a rubber mallet to tap
caster stem into posts. (See Figure 3)
Figure 3

0313 IH-2449PAGE 2 OF 3
UNIT ASSEMBLY
1. Snap shelf supports into the very bottom groove of
two short and two tall posts. (See Figure 4)
2. Slide posts through underside of square shelf until it
slides firmly over the supports. (See Figure 5)
3. Take the other four tall posts, snap shelf supports into
the very bottom groove on all four posts. Slide posts
through underside of square shelf until it slides firmly
over the supports. (See Figure 6)
4. Position each set of four posts as shown and snap
four sets of shelf supports into the groove directly
above the square shelves of the inner four posts.
(See Figure 7)
5. Slide a square shelf onto the inner four posts until
shelf slides firmly over the supports. (See Figure 8)
6. Snap four sets of shelf supports onto the outer posts
with 5 grooves visible. And 4 sets of shelf supports on
the inner posts with 3 grooves visible. (See Figure 9)
7. Slide two square shelves onto the posts until shelves
slide firmly over the supports. (See Figure 10)
Figure 7
Figure 8
ASSEMBLY CONTINUED
Figure 4 Figure 5
Figure 6
Figure 9
Figure 10

0313 IH-2449PAGE 3 OF 3
ASSEMBLY CONTINUED
UNIT ASSEMBLY CONTINUED
8. Snap eight sets of shelf supports onto the posts with
five grooves visible on all eight posts. Slide two
square shelves onto the posts until shelves slide firmly
over the supports.
9. Repeat step 8 one more time. (See Figure 11)
LEFT SIDE OF THE UNIT
10. Snap four sets of shelf supports onto the left four posts
with twelve grooves visible between the lower shelf.
11. Slide a square shelf onto the posts until shelf slides
firmly over the supports. (See Figure 12)
12. Repeat steps 10 and 11 twice. (See Figure 12)
RIGHT SIDE OF THE UNIT
13. Snap four sets of shelf supports onto two inner posts
and two outer posts. (See Figure 13)
14. Slide the rectangular shelf at the top of the posts until
shelf slides firmly over the supports. (See Figure 13)
15. Slide garment rod hangers onto garment rod.
(See Figure 14)
16. Slide the longer end of garment rod hangers
through the shelf wires. (See Figure 15)
17. Hook the short end of garment rod hangers onto the
center wire of the shelf. (See Figure 16)
18. Pull garment rod
back and down,
one side at a time,
until long end
of garment rod
hanger snaps into
place.
Fig ur e 11
Figure 12
Figure 13
Figure 14
Figure 15
VIEW FROM
THE BOTTOM
Figure 16
π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA
1- 80 0 -295 - 5510
uline.com