U-Line H-2932 User manual

PAGE 1 OF 4 1215 IH-2932
πH-2932, H-4734
DIGITAL
KEY CABINET
1-800-295-5510
uline.com
FEATURE KNOB KEYPAD
BUTTONS
PROGRAM
BUTTON
GREEN AND
RED LEDS
YELLOW
LED
FUNCTION
Moves lock mechanism
90 or 180 degrees
clockwise or
counterclockwise
to lock and unlock
cabinet.
For entering and
programming lock
codes.
Initiate programming
mode by pressing the
front thin edge of the
black button inward
toward the mounting
surface the lock is
mounted to.
Will flash and
illuminate to indicate
operating conditions.
Will flash five times
after lock is operated
to signify the battery
level is low and should
be replaced.
OVERVIEW OF CONTROLS
INSTRUCTIONS
This lock can operate using 3 codes (Factory or Master
code, Supervisor code, and User code).
Factory Code – is the only code set
in the lock at this time. This code must
be reprogrammed to a 6 digit Master
Code. (See Page 2)
Supervisor and User Code – (3 to 6)
digits need to be programmed into
the lock by following the steps. All
codes are retained by the lock after
unlocking and if the battery is changed.
A Note on Codes – The numbers 6, 7, 8, and 9 can be
entered by pressing two keys simultaneously in order to
produce a sum.
For example 2 and 4 can be pressed simultaneously to
produce the number 6 (2 + 4 = 6).
NOTE: If the code was programmed using
2 + 4 as the 6 digit, the 2 + 4 must be used
when accessing the lock, because other
combinations that equal six such as 1 + 5 are
distinguished from 2 + 4.
5
5
56
5
5
50
5
49
2
5
28
5
27
345
2
1
ELECTRONIC LOCK ELECTRONIC LOCK FEATURES
#DESCRIPTION
1Knob
2Keypad
3Battery Holder With Cover
4Program Button
5 Yellow Low Battery LED
6 Red Error LED
7Green Proceed LED
1 3
4 5 6 7
2
ELECTRONIC LOCK FUNCTIONS
Factory/Master
Code
Supervisor Code
3-6 Digits
User Code
3-6 Digits

PAGE 2 OF 4 1215 IH-2932
TO PROGRAM TO A 6-DIGIT MASTER
CODE (overwrite the default Factory code):
THE FACTORY CODE IS 531423 AND MUST BE OVERWRITTEN
BY A NEW 6 DIGIT MASTER CODE.
1. With knob in the unlocked position, press the
program button 5 times until the green LED lights up.
2. Enter the default 6 digit Factory code.
a. If the code is correctly entered, the GREEN and
RED LEDs will flash.
b. If the code is incorrectly entered, the RED LED will
flash.
3. Enter the Factory code again. The RED, GREEN and
YELLOW LEDs will light up.
4. Enter the desired 6 digit Master code. The RED,
GREEN and YELLOW LEDs will simultaneously flash.
5. Enter the newly created Master code again.
a. If incorrect, the RED LED will flash.
b. If the code is entered correctly, all 3 LED`s will
flash consecutively for 5 seconds.
Your Master code is now stored. The Factory code is
erased. To program a NEW Master code, follow the
same procedure above, entering the current Master
code instead of the Factory code.
TO PROGRAM A SUPERVISOR CODE:
1. With the knob in either the unlocked or locked
position, press the program button. If you do not
enter either the Master code or control key-fob
within 10 seconds, the red error light will flash and
exit programming.
2. Enter the Master code provided with your lock.
a. If you do not enter a Supervisor code within 10
seconds, the red error light will flash twice and
exit programming.
b. If you enter the Master code incorrectly. the red
error light will flash and exit programming.
c. If you enter the Master code or the control key-fob
correctly, the red light will light up for 10 seconds.
3. Enter a User code (3-6 digits in length).
4. Push the program button again to finish. A successful
code storing is indicated by 6 green light flashes.
TO PROGRAM A USER CODE:
1. With the knob in the unlocked or locked position,
press program button twice. The red LED will light up.
2. Enter the Supervisor code.
a. If you do not enter either the Supervisor code
within 10 seconds, the red error light will flash
and exit programming.
b. If you enter the Supervisor code incorrectly, the
red error light will flash and exit programming.
c. If you enter the Supervisor code correctly, the
yellow LED will light up for 10 seconds.
3. Enter a User code (3-6 digits in length). If you do not
enter a User code within 10 seconds, the red error
light will flash and exit programming.
4. Push the program button again to finish. A successful
code is indicated by 6 green light flashes.
TO ERASE THE USER CODE
1. Press the program button twice. The red LED will
light up.
2. Enter the Supervisor code.
a. The yellow LED will light up for 10 seconds.
b. If the Supervisor code is entered incorrectly,
the red error light will flash twice and exit
programming.
3. Enter 1-1-1-1-1.
4. Press the program button. If the User code is
successfully erased, the green LED will flash 6 times.
PROGRAMMING

PAGE 3 OF 4 1215 IH-2932
1. Use indent to pull battery away from the unit.
(See Figure 1)
2. Make sure it is fully extended out. (See Figure 2)
3. Swing battery cover up. (See Figure 3)
4. Using Allen wrench, remove retaining Allen screw.
(See Figure 4)
5. Pull out battery holder. (See Figure 5)
6. Replace battery. (See Figure 6)
When entering a valid code, you should hear a ‘click’
sound. The green LED will light up, and you can turn the
knob to the unlocked position.
An incorrect code is indicated by three flashes of the
red error light.
Five incorrect entries will result in the lock being
temporarily disabled for 2 minutes; during this time any
entry attempts will be met with three flashes of the red
error light.
TO RE-LOCK:
Turn the knob from the unlocked position to the locked
position, listen for the lock mechanism to operate by
hearing a "click" sound, and confirm the knob is locked.
USING THIS LOCK IN LOCKER MODE:
Follow the procedure below to change operation mode
from Single User/Station mode to Locker mode :
1. Unlock the unit.
2. Remove the battery for 10 seconds.
3. Press the PROGRAM Key while the battery is removed.
4. Insert battery and continue holding PROGRAM key.
5. Wait until all 3 LEDs (Red, Green and Yellow) turn on
and fade out at the same.
6. Release the PROGRAM key.
7. Enter the 6 digit Master code.
8. If code was entered correctly, the yellow LED will be lit.
9. Press button number 2.
10. Once the lock switches to Locker mode, the LEDs
will each flash for one second in the following order:
Green, Yellow and Red.
11. Proceed to operate the lock in Single User/Station mode.
OPERATION
REPLACING THE BATTERY
Indent
Figure 1 Figure 4
Figure 5
3-Volt Lithium CR2032
3-Volt
Figure 6
Figure 2
Figure 3

PAGE 4 OF 4 1215 IH-2932
7. Push in battery holder. (See Figure 7)
8. Tighten retaining Allen screw. (See Figure 8)
9. Swing battery cover down. (See Figure 9)
10. Push into locked position. (See Figure 10)
11. If the battery is inserted while the knob is locked,
you should hear the lock mechanism click and the
unit will lock. If the battery is inserted while the knob
is unlocked, after turning the knob to the locked
position, you will hear the lock mechanism click and
the unit will lock.
NOTE: If the unit will not lock after inserting the
battery, enter the factory code, move the knob
to the unlocked position, then move the knob
to the locked position and you should hear the
lock mechanism click and the unit will lock. If
the unit does not lock, replace the battery.
REPLACING THE BATTERY CONTINUED
Figure 7
Figure 8
Figure 9
Figure 10
πCHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA
1-800-295-5510
uline.com