Uberhaus 72255159 User manual

Page 1
Model/Modèle ：72255159
10' x 10' Gazebo
User manual p. 2
Abri-soleil 10 x 10 pi
Guide de l'utilisateur p. 25

Important Safety Instruc ons
WARNING! To reduce the risk of serious injury or damage to equipment, read all
of the following safety instruc ons before assembling and using the gazebo.
Failure to follow these warnings may result in serious injury or death.
•Keep all children and pets away from assembly area. Children and pets should be supervised while gazebo is
being assembled.
•The assembled gazebo should be located at least 6 feet (2 m) from any obstruc on such as fence, garage,
house, overhanging branches, laundry lines or electrical wires.
Consult with local municipal office for specific requirements.
•This product is for domes c outdoor use i.e. decora ve and sunshade purpose only.
•Install the gazebo on level ground. Stakes are provided to secure the gazebo to the ground. Do not assemble
the gazebo on sandy, muddy or loose soil, as stakes do not have enough anchorage in these types of soil. If you
wish to secure the gazebo to a wood deck or concrete surface, use anchors suited to these surfaces (anchors
not included).
•Some parts may contain sharp edges. Wear protec ve gloves if necessary during assembly.
•This unit is heavy. DO NOT assemble this item alone. Make sure there is sufficient manpower for safe
assembling or moving the gazebo.
•Check all nuts and bolts periodically for htness and when required, ghten them again.
•While this gazebo is manufactured to withstand winds through only the supplied ground stakes, in areas
subject to frequent severe weather, securing the gazebo to a deck, concrete pa o or foo ngs should be
considered.
•Remove accumulated water on the roof immediately, or disassemble the gazebo in order to avoid damage.
• Snow must be cleared off regularly during a snow day, remove snow at the top when it is thicker than 4''
(10 cm). In order to avoid damages, use a plas c snow rake to remove excessive snow and ice buildup from
roof and keep away from falling debris.
•ALWAYS DISASSEMBLE the gazebo before experiencing heavy wind condi ons, as it is semi-permanent
construc on and not designed to withstand harsh weather,
including high wind, rain and snow.
Page 2
•Please check your state and local regula ons prior to purchasing. Some jurisdic ons may require permits
for installa on and use.
Some special procedures may be valid in your area.
CAUTION
•DO NOT use or enter the gazebo under harsh weather (e.g. thunderstorms, high winds, hail, heavy snow, etc.).
In these condi ons, it might p over and could cause serious injury to bystanders. Any damage or injury
caused by which is not covered by the warranty.
•DO NOT install the gazebo adjacent to trees or a sloped roof. Snow and ice may slide onto the gazebo and
cause it to collapse.
•DO NOT use or enter the gazebo if
1. Visible movement of support members, roofing panels or sagging roofline.
2. Creaks or audible noise from the gazebo.
3. Cracks, fractures or malforma on of support member or roof panels.
4. Damaged or missing fasteners.

Page 3
•DO NOT hang any weights on the roof frame.
•DO NOT lean a ladder against the gazebo or climb onto the roof.
•Keep away from heat or flame source.
•If the gazebo will not be used for a long period of me (e.g. during winter me), disassemble and store it in a
clean, dry environment.
PREPARATION
Required for Assembly:
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents
list and hardware contents list.
If any part is missing or damaged, do not a empt to assemble the product.
Arrange manpower of 4 or more when assembling or moving the product.
Es mated Assembly Time: 90 - 120 minutes.
CARE AND MAINTENANCE
•Our steel components for gazebo and garden accessories are treated with rust inhibi ng paint that protects
it from rus ng. However, due to the nature of steel,
surface oxida on (rus ng) will occur if these
protec ve
coa ngs are scratched. This is not a defect and thus not covered by the warranty.
To minimize this condi on, we recommend care when assembling & handling the product to prevent
scratching the paint.
Should any scratching or damage occur, we recommend immediate touch-up with rust inhibi ng paint.
Surface rust can also be easily removed with a very light applica on of regular cooking oil. If surface oxida on
(rus ng) occurs and if no measure is taken to prevent this,
the oxida on may start dripping onto deck or pa o and caused damaging stains, which may be difficult to
remove.
This can be prevented if the above-men oned measures are taken to keep the product from oxidizing.
•Do not use bleach, acid, or other abrasive cleaners on the roof or frame parts.
•Keep user manual for future reference.
•Keep the original packaging to store the gazebo.

Page 4
APost 1
A1 Post 1
BPost 2
B2 Supporting Post for Winter 1
B3 Supporting Post for Winter 1
CRail 1
C1 Rail 1
DRail 1
ERail 1
FLintel 1
GLintel 1
G2 Decorative Reinforcement
Bar 2
HRoof Holder Bar (back) 1
IRoof Holder Bar (front) 4
JRoof Corner Bar 1
Parts List

Page 5
J1 Roof Corner Bar 1
J2 Roof Central Bar 3
KMain Roof Panel 8
K1a Side Roof Panel 1
K2a Side Roof Panel 1
K1b Side Roof Panel 1
K2b Side Roof Panel 1
LRoof Supporting Tube 4
MSide Cap 1
M1 Side Cap 1
RHook 72
SScreen 4
S1 Curtain 4

Page 6
NOTE: The material is not to scale
NBase Plate 2 V Screw M6*15 63
N1 Anchor Bracket 4 W Screw M6*10 5
N2 Base Plate 2 W1 Screw M6*50 10
OConnector 2 W2 Screw M6*12 5
PConnector 9 X Screw M6*15 32
P1 Connector 6 Y Nut 10
QEnd Cap 1 Y1 Nut 10
Q1 End Cap 1 Z Allen Key 2
Q2 End Cap 3 Z1 Wrench 1
TScrew M6*38 5 Z2 Stake 14
UScrew M6*20 4
HARDWARE KIT INCLUDED

Page 7
Step 1
A
N1
U
A
VN
B
VN2
N2
B
A
N1
N1
A1
N1
U
N2
B
N1
N1
A1
N
1.1. Attach the Connector (N1) onto the Post (A) and (A1) by using Screws (U).
1.2. Attach the Base Plate (N) to the bottom of the Post (A and A1) by using the Screws (V).
1.3. Attach the Base Plate (N2) to the bottom of the Post (B) by using the Screws (V).
NOTE:
Make sure the convex edge of the Base Plate (N) is facing the front of the Post, as shown in the
above drawing.
The bolts to fix the Anchor Bracket (N1) to the wall are not provided and must be purchased
separately.

Page 8
Step 2
2.1. Insert t elve Hooks (R) into the Rail (C) and twelve Hooks (R) into the Rail (C1) by sliding
them into the appropriate location designed for the hooks.
2.2. Insert twelve hooks (R) into the Rail (D) by sliding them into the appropriate location designed for
the hooks.
NOTE:
Make sure the direction of the Hooks matches the above drawing.
The Shelter has two Rails: one for the Screen and one for the Curtains. The Hooks for the
Curtains must be placed on the internal Rail. The same number of Hooks must be used for the
Curtains and Screen.
C/C1
C/C1
D
R×12
R×1
D

Page 9
Step 3
3.1. Attach the assembled Rail (D) to bothPosts (B) with Screws (X).
3.2. Attach the assembled Lintel (F) to Posts (A & A1) with Screws (X).
3.3. Attach the side Rail (C) to Posts (A & B) with Screws (X). Attach the Rail (C1) to Posts (A1 & B)
with Screws (X).
Make sure the Rails are placed with the sides with Hooks towards the inside of the Shelter.
A
A1
C1
D
X
F
B
D
C
XX
B
X
C
F

Page 10
Step 4
4.1. Attach Connector (O) to Rail (C) with Screws (V).
4.2. Attach Connector (O) to Rail (C1) with Screws (V).
4.3. Place the assembled Lintel (G) onto the Connectors (O) with Screws (V).
Ensure that the Screws are well tightened.
VO
O
O
G
C
C1

Page 11
Step 5
5. Insert the Screws (W1), (W2), (W1) into the grooves of each Roof Corner Bar (J & J1) and each
Roof Central Bar (J2).
X 5
W1
W1
W1
W1
W1
J1
J2
J
W1
W1
W2
W2
W2
W2
W1

Page 12
Step 6
6.1. Attach a Connector (P1) to each end of the Lintel (F) and (G) and to the end of the Rail (D) with
the Screws (V).
6.2. Put the Roof Holder Bars (J & J1) onto the Connectors (P1) which are installed at the ends of the
Lintel (G). Place Screws in the center of the Roof Holder Bars (J & J1) into the holes of the Connectors,
and fix them with Nuts (Y1).
6.3. Attach the Roof Holder Bars (J & J1) by passing Screws (V) through the holes on the top of
Connectors (P1).
NOTE:
The Long Screws (W1) previously inserted on the Roof Holder Bars (J & J1) will be used in
Step 10.
J1
C1
J1
P1
F
F
G
D
D
G
Y1
P1
P1
V
V
J
J
J
V

Page 13
Step 7
7.1. Insert the Side Roof Panels (K1a & K1b) between the Rails (C & C1) and the Roof Holder Bars (J
& J1) which form a triangle on the sides of the shelter.
7.2. Insert the Side Roof Panels (K2a & K2b) between the Rails (C & C1) and the Roof Holder Bars (J
& J1) which form a triangle on the sides of the shelter, until they reach the Side Roof Panels (K1a &
K1b)
CAUTION:
One side of each Roof Panel is treated to provide UV protection. Make sure that the side
treated with UV protection is facing outward. This step is very important – if the roof is not
assembled as per the instructions shown, it will not be covered by the warranty.
NOTE:
The panels are covered with a plastic film to identify which side has UV protection. Once this
film is removed, it is not possible to tell which side protects against UV rays. Therefore, it is
recommended to remove the film only once the panels have been installed, one at a time.
C
C
J1
J
C1
J
K1a
K1a
K2a
K2b
K1b

Page 14
Step 8
8. Attach the Rail (E) to the Rail (D) with Screws (T).
X 5
D
D
T
T
E
E

Page 15
Step 9
9. Attach the Connectors (P) to the assembled Lintels (D,F & G) with Screws (V).
X 9
P
P
P
P
P
P
P
P
P
P
G
D
F
V

Page 16
Step 10
10.1. Install the Roof Central Bars (J2) aligning the small Screws in the center of the Bars (J2) with the
holes of the Connectors (P) found on the Lintel (G); fix them with Nuts (Y1).
10.2. Attach the end of the Roof Central Bars (J2) to the Bars (D & F) with Screws (V) in the holes of the
Connectors (P).
NOTE:
Long Screws (W1) previously inserted in the Roof Holder Bars (J2) will be used in Step 11 to
install the Reinforcement Bars.

Page 17
Step 11
11. From within the shelter, install the Reinforcing Bars (G2) by inserting the screws which protrude
from the Roof bars (J2) into the Reinforcing Bars (G2) and fixing them with Nuts (Y).
NOTE:
Ensure that the Decorative Reinforcement Bars (G2) are well centered before tightening the
Nuts (Y).
X 10 X 10
J/J1/J2
G2
G2
G2
G2
Y
J/J1/J2

Page 18
Step 12
12. Attach the Back Roof Holder Bar (H) with Screws (V).
X 3
V
H
H
V
J/J1
J2

Page 19
Step 13
13.Attach the Side Caps (M & M1) with Screws (V).
C/C1
V
M
M1
H
V
M/M1
C/C1
J/J1
J/J1

Page 20
Step 14
14. From the front of the Shelter, slide five Main Roof Panels (K) in the grooves of the Roof Holder
Bars all the way tothe end (1 per row).
CAUTION:
One side of each Roof Panel is treated to provide UV protection. Make sure that the side with UV
protection is facing outward. This step is very important – if the roof is not assembled as per the
instructions shown, it will not be covered by the warranty.
NOTE:
The panels are covered with a plastic film to identify which side is treated with UV protection. Once this
film is removed, it is not possible to tell which side protects against UV rays. Therefore, it is
recommended to remove the film only once the panels have been installed, one at a time.
X 4
KK
J2
J1
J
KK
K
G2