Uberhaus 72255162 User manual

Page 1
Model/Modèle ：72255162
10' x 10' Gazebo
User manual p. 2
Abri-soleil 10 x 10 pi
Guide de l'utilisateur p. 20
#0807698

Page 2
Important Safety Instruc ons
WARNING! To reduce the risk of serious injury or damage to equipment, read all
of the following safety instruc ons before assembling and using the gazebo.
Failure to follow these warnings may result in serious injury or death.
•Keep all children and pets away from assembly area. Children and pets should be supervised while gazebo is
being assembled.
•The assembled gazebo should be located at least 6 feet (2 m) from any obstruc on such as fence, garage,
house, overhanging branches, laundry lines or electrical wires.
Consult with local municipal office for specific requirements.
•This product is for domes c outdoor use i.e. decora ve and sunshade purpose only.
•Install the gazebo on level ground. Stakes are provided to secure the gazebo to the ground. Do not assemble
the gazebo on sandy, muddy or loose soil, as stakes do not have enough anchorage in these types of soil. If you
wish to secure the gazebo to a wood deck or concrete surface, use anchors suited to these surfaces (anchors
not included).
•Some parts may contain sharp edges. Wear protec ve gloves if necessary during assembly.
•This unit is heavy. DO NOT assemble this item alone. Make sure there is sufficient manpower for safe
assembling or moving the gazebo.
•Check all nuts and bolts periodically for htness and when required, ghten them again.
•While this gazebo is manufactured to withstand winds through only the supplied ground stakes, in areas
subject to frequent severe weather, securing the gazebo to a deck, concrete pa o or foo ngs should be
considered.
•Remove accumulated water on the roof immediately, or disassemble the gazebo in order to avoid damage.
• Snow must be cleared off regularly during a snow day, remove snow at the top when it is thicker than 4''
(10 cm). In order to avoid damages, use a plas c snow rake to remove excessive snow and ice buildup from
roof and keep away from falling debris.
•ALWAYS DISASSEMBLE the gazebo before experiencing heavy wind condi ons, as it is semi-permanent
construc on and not designed to withstand harsh weather, including high wind, rain and snow.
•Please check your state and local regula ons prior to purchasing. Some jurisdic ons may require permits
for installa on and use.
Some special procedures may be valid in your area.
CAUTION
•DO NOT use or enter the gazebo under harsh weather (e.g. thunderstorms, high winds, hail, heavy snow, etc.).
In these condi ons, it might p over and could cause serious injury to bystanders. Any damage or injury
caused by which is not covered by the warranty.
•DO NOT install the gazebo adjacent to trees or a sloped roof. Snow and ice may slide onto the gazebo and
cause it to collapse.
WARNING:
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC.
This tent meets the CPAI-84 flammability requirements. The fabric may burn
if le in connuous contact with any flame source. The applicaon of any foreign
substance to the tent fabric may render the flame-resistant properes ineffecve.

•DO NOT use or enter the gazebo if
1. Visible movement of support members, roofing panels or sagging roofline.
2. Creaks or audible noise from the gazebo.
3. Cracks, fractures or malforma on of support member or roof panels.
4. Damaged or missing fasteners.
Page 3
•DO NOT hang any weights on the roof frame.
•DO NOT lean a ladder against the gazebo or climb onto the roof.
•Keep away from heat or flame source.
•If the gazebo will not be used for a long period of me (e.g. during winter me), disassemble and store it in a
clean, dry environment.
PREPARATION
Required for Assembly:
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents
list and hardware contents list.
If any part is missing or damaged, do not a empt to assemble the product.
Arrange manpower of 4 or more when assembling or moving the product.
Es mated Assembly Time: 90 - 120 minutes.
Maximum load for the roof hook: 50lbs.
CARE AND MAINTENANCE
•Our steel components for gazebo and garden accessories are treated with rust inhibi ng paint that protects
it from rus ng. However, due to the nature of steel, surface oxida on (rus ng) will occur if these protec ve
coa ngs are scratched. This is not a defect and thus not covered by the warranty.
To minimize this condi on, we recommend care when assembling & handling the product to prevent
scratching the paint.
Should any scratching or damage occur, we recommend immediate touch-up with rust inhibi ng paint.
Surface rust can also be easily removed with a very light applica on of regular cooking oil. If surface oxida on
(rus ng) occurs and if no measure is taken to prevent this,
the oxida on may start dripping onto deck or pa o and caused damaging stains, which may be difficult to
remove.
This can be prevented if the above-men oned measures are taken to keep the product from oxidizing.
•Do not use bleach, acid, or other abrasive cleaners on the roof or frame parts.
•Keep user manual for future reference.
•Keep the original packaging to store the gazebo.

(1) Upper Central
Connector
Lower Central
Connector
Long Bar
Short Bar
Long Lintel
Short Lintel
Lintel Cover
Connector
Connection Piece
Parts List
Top Connector
#3 Left Support
Tube
1# Left Support
Tube
1# Right Support
Tube
2# Left Support
Tube
1
1
4
4
4
4
4
4
8
4
4
4
4
4
4
4
4
4
4
Post
Base Plate
(14)
(15)
(16)
(17)
(18)
(19)
Page 4
(2)
(3)
(4)
(9)
(11a)
(12a)
(13)
(5a)
(6)
(6a)
(7)
(8)
2# Right Support
Tube
#3 Right Support
Tube
(10) Connecting Tube of
Mosquito Net 4

4
(20) 4# Left Support
Tube
(22)
(23)
(24b)
(24a)
(25a)
(25b)
(26a)
(27)
Long Bar Connector
Short Bar Connector
Large Polycarbonate
Sheet
Parts List
Mosquito Net
Large Polycarbonate
Sheet
Mosquito Net Tube
4
4
4
4
4
4
8
4
Small Polycarbonate
Sheet
Small Polycarbonate
Sheet
Page 5
4
(21) 4# Support
Tube

(28)
(29)
(30)
(31)
(31a)
(32)
(33)
(34)
(36)
(37)
(38)
Hardware List
32
8
77
32
16
16
12
Hanger
Stake
Bolt\Flat Washer
M6*15
Bolt\Flat Washer\ Nut\
Plastic Nut Cap
Bolt\Flat Washer\Nut\
Plastic Nut Cap
M6*70
M6*15
Screw
Bolt\Plastic Washer
M6*40
Wrench
Allen Wrench
Allen Wrench
Bolt\Steel Washer
M6*15
1
1
2
8
Page 6

16
12
Bolt\Flat Washer\Nut\
Plastic Nut Cap
M6*70
Bolt\Plastic Washer
M6*40
Fig. 1
Fig. 1
Fig. 2
Fig. 2
1. Insert Connector (7) into Short Lintel (6) and connect them by bolt (38). See Fig.1
2. Insert Connector (7) into Long Lintel (5a) and connect them by bolt (38), at the
same time,
attach the Lintel Cover (6a) to Lintel (5a/6) with bolts (38).
Connect Connection Piece (9) with Long Lintel (5a) by bolt (33); connect Connection tube of
Mosquito net (10) with Long Lintel (5a) by bolt (37).
Insert Mosquito Net tube (26a) into Connection tube of Mosquito net (10).
Connect Mosquito Net tube (26a) with Lintel (5a)/(6) by bolt (37).See Fig.2
(37)
(38)
Step 1:
Page 7
(33)
(37)
(37)
(10)
(26a) (26a) (26a)
(10)
(5a)
(5a)
(5a) (5a)
(5a) (6)
(6)
(6)
(6a)
(6)
(6)
(6a)
(6)
(7)
(7)
(7)
(5a)
(9)
(38)
(38)
(33) Bolt\Flat Washer
M6*15 8
(38)

3. Connect Base Plate (13) and Post (12a) by bolt (33). See Fig.3
4.Attach Lintel (5a)/(6) to Post (12a) with Bolt (33). Repeat on each corner. See Fig.4
5.Attach Bracket Piece (8) to Short Lintel (6) and Post (12a) with Bolt (33). Repeat on each
corner. See Fig.5
Fig. 4
Fig. 4/Fig. 5
Fig. 5
Fig. 3
Fig. 3
(33)
(12a)
(12a)
(12a)
(33)
(33)
(33) (33)
(12a)
(12a)
(5a)
(6)
(6)
(6)
(5a)
(5a)
(5a) (6)
(5a) (6)
(5a)
(8)
(8)
(12a)
(12a)
(13) (33)
(33)
Step 2: Bolt\Flat Washer
M6*15 48
Page 8

6. Screw Bolt (34) to Lower Central Connector (2).Note: do not over-tighten. See Fig.6
7. Attach Top Connector (11a) to Long Bar (3) with Bolts (32); insert two Bolts (34) into the slot
of Long Bar (3) from the other end. Repeat on each side. See Fig.7
8. Insert two Bolts (34) into the slot of Short Bar (4) from the end of insert nut; the insert nut will
connect with the other small piece. Repeat on each side. See Fig.8
Page 9
Fig.6
Fig.7
Fig.8
X16
X16
X2
X2
(33)
(34)
Step 3: (32)
(2)
(2)
(3)
(34) (34)
(34)
(32)
(3)
(4)
(4)
(11a)
Bolt\Steel Washer
M6*15
Bolt\Flat Washer
M6*15
Bolt\Flat Washer\ Nut\
Plastic Nut Cap
M6*15
8
12
32

9. Insert Long Bar (3) which has the connected small piece into Bolt (34) of Lower Central
Connector (2), tighten Bolt (34). See Fig.9
10. Insert the other Long Bar (3) on an angle into Bolt (34) of Lower Central Connector (2),
tighten Bolt (34). See Fig.10
11. Attach Top Connector (11a) located below Long Bar (3) to Post (12a) with Bolt (33). See Fig.11
(6)
(5a)
(6)
(5a)
(6)
(5a)
(12a)
(12a)
(12a)
(12a)
(12a)
(34)
(3)
(3)
(3) (3)
(33) (3)
(2)
(2)
(3)
Fig.9
Fig.9/Fig.10
Fig.10 Fig.11
Fig.11
Fig.11
Page 10

12. Insert the third Long Bar (3) into Bolt (34) of Lower Central Connector (2), and tighten Bolt (34).
See Fig.12
13. Attach Top Connector (11a) which is below Long Bar (3) to Post (12a) with Bolt (33). See Fig.13
(2)
(3) (3)
(3)
Fig.12
Fig.12Fig.13
Fig.13
Fig.13
Page 11
(3)
(6)
(5a)
(5a)
(6)
(6)
(5a)
(12a)
(12a)
(12a)
(12a)
(12a)
(3)
(3) (3)
(3)
(33)

14. Insert Short Bar (4) into Bolt (34) of Lower Central Connector (2), and tighten Bolt (34).
See Fig.14
15. Attach underside of Short Bar (4) to Connection Piece (9) with Bolt (33). See Fig.15
Page 12
Fig.14
Fig.14
Fig.15
Fig.15
Fig.15
(3)
(3)
(3)
(3)
(2)
(4)
(4)
(9)
(5a)
(5a)
(5a)
(6)
(6)
(3) (33)
(3)
(3)
(4)
(4)

16. Insert Short Bar (4) into Bolt (34) of Lower Central Connector (2), and tighten Bolt (34).
See Fig.16
17. Attach underside of Short Bar (4) to Connection Piece (9) with Bolt (33). See Fig.17
Fig.17
Fig.17
Fig.17
Fig.16
Fig.16
(3)
(3)
(3)
(33)
(3)
(3)
(4)
(4)
(4)
(3)
(4) (9)
(4) (5a)
(5a)
(6)
(6)
(5a)
(5a)
(4)
Page 13
(4) （2）

Fig.18
Fig.18
Fig.19
Fig.20
Fig.21
18. Attach Upper Central Connector (1) to Upper Central Connector (2) with Bolt (33). See Fig.18
(24b)
(24a)
(16)
(4)
(1)
(2)
(33)
(33)
Step 4: Bolt\Flat Washer
M6*15 1
Page 14

Fig.19
Fig.20
Fig.21
(4) (4)
(4)
(4)
(16)
(17)
(4)
(4)
(24b)
(25b)
(24b)
(25b)
(16)
(17)
(24a)
(25a)
(24a)
(25a)
19. Insert Small Polycarbonate Sheet (24a/25a) into slot of Top Bar. Adjust position of Small
Polycarbonate Sheet (24a/25a). Insert #2 Left Support Tube (16) and #2 Right Support Tube (17)
into the lower slot on Top Bar. Adjust position and ensure that they are vertical and parallel. Then,
insert Large Polycarbonate Sheet (24b/25b) into slot of top Bar, and adjust position of Large
Polycarbonate Sheet (24b/25b). Repeat on each side. See Fig.19 to Fig.21
Page
15

Fig.22
(20)
(24b)
(24b)
(24b)
(24b)
(25b)
(25b)
(21)
(12a)
(4)
(21) (21)
(20)
(25b)
(20)
(33)
(4)
(3)
Fig.22/Fig.24
Fig.23/Fig.25
(33)
(36)
Step 5: Bolt\Flat Washer
M6*15
Screw 16
8
Page 16

Fig.23 Fig.24
Fig.25
20. Attach #4 Left Support Tube (20) and 4# Right Support Tube (21) to Short Bar (4) with Bolt (33),
and attach #4 Right Support Tube (21) and 4# Left Support Tube (20) to Long Bar (3) with Bolt (33),
and repeat the above six steps with the remaining support tubes and short bars. When that
assembly is finished, adjust the position of supporting tubes, ensuring that they are vertical and
parallel. Finally, adjust top connector and top bar to their correct position. Attach Short Bar
Connector (23) to Short Bar (4) with Screw (36). Attach Long Bar Connector (22) to Long Bar (3)
with Screw (36). See Fig.22-Fig.25
(3)
(3)
(4)
(21)
(20) (23)
(22)
(12a)
(12a)
(5a)
(33)
(36)
(36)
(25b)
(25b)
(25b)
(24b)
(24b)
(24b)
Page 17

Fig.26 Fig.27
Fig.26
Fig.27
21. Attach #1 Left Supporting Tube (14) and #1 Right Supporting Tube (15) to Long Bar (3) and
Short Bar (4) with Bolt (34). Attach #3 Left Supporting Tube (18) and #3 Right Supporting Tube
(19) to Long Bar (3) and Short Bar (4) with Bolt (34). See Fig.26 and Fig.27
(14)
(15)
(15)
(5a)
(34)
(34)
(34)
(34)
(19)
(18)
(4) (4)
(3)
(3)
(5a)
(6) (18)
(14)
(14)
(19)
(18)
(4)
Step 6:
Page 18

Fig.28 Fig.29
22. Hang Mosquito Net (27) onto the Mosquito Net Tube(26a) with Hanger(28). See Fig.28
23. Adjust position of Gazebo and anchor posts to the ground by inserting Stakes (29) into each
hole in each Base Plate(13). See Fig.29
Your gazebo is now ready for use.
(29)
Step 7: 8
Stake
Page 19
(26a)
(12a)
(27)
(29) (13) (29)
(28)
Fig.28
Fig.29

Direc ves de sécurité importantes
AVERTISSEMENT! Afin de réduire le risque de blessures graves ou de dommage à l’équipement,
lire toutes les instruc ons ci-dessous avant d’assembler et d’u liser l’abri-soleil. Négliger de
suivre ces aver ssements peut provoquer des blessures graves ou la mort.
•Gardez les enfants et les animaux de compagnieloin de l’aire d’assemblage. Les enfants et les animaux
devraient être surveillés pendant l’assemblage de l’abri-soleil.
•L’abri-soleil doit être assemblé à une distance d’au moins 2 m (6 pieds) de tout obstacle comme une clôture,
un garage, des branches en surplombantes, une corde à linge ou des fils électriques. Consultez les
bureaux municipaux de votre région pour les exigences spécifiques.
•
d’ombrage.
•Installez l’abri-soleil au niveau du sol. Des piquets sont fournis pour sécuriser l’abri-soleil au sol. N’assemblez
pas l’abri-soleil sur un sol sablonneux, boueux ou meuble, qui ne convient pas à l'ancrage des piquets. Si vous
souhaitez sécuriser l’abri-soleil sur une terrasse en bois ou une surface de béton, u lisez des pieux conçus
pour ces surfaces (piquets non compris).
•Certaines pièces peuvent avoir des bords tranchants. Portez des gants de protec on si nécessaire pendant
l’assemblage.
•Ce e unité est lourde. NE PAS assembler cet ar cle seul. Veillez à ce qu’il y ait un nombre suffisant de
main d'oeuvre pour l'assemblage ou le déplacement de l’abri-soleil.
•Vérifiez chaque écrou et boulon périodiquement pour resserrer si nécessaire.
•Bien que cet abri-soleil soit conçu pour résister au vent uniquement grâce aux piquets fournis, dans les
endroits fréquemment sujets à du temps violent, sécurisez l’abri-soleil à une terrasse en bois ou en béton ou
considérez des fonda ons.
•Re rez l’eau accumulée sur le toit immédiatement ou démontez l’abri-soleil dans le but d’éviter les
dommages.
•La neige doit être enlevée régulièrement lors d’une tempête, re rez la neige du toit lorsque la quan té
aeint 10 cm (4 po). Pour prévenir les dommages, u lisez un râteau en plas que pour l’excès de
neige et l’accumula on de glace du toit et restez loin afin d’éviter la chute de débris.
•TOUJOURS DÉMONTER l’abri-soleil avant l’arrivée de forts vents, puisque c’est une construc on
semi-permanente et qu’elle n’est pas conçue pour résister aux condi ons météorologiques extrêmes,
notamment le vent violent, la pluie forte et la neige en grande quan té.
•Informez-vous sur la réglementa on provinciale et locale avant d’effectuer l’achat. Certaines autorités
peuvent être requises dans votre secteur.
PRÉCAUTIONS
•NE PAS uliser ou rester à l’intérieur de l’abri-soleil lors de condi ons extrêmes (par. ex. des orages, des vents
blessures sérieuses aux occupants. Tout dommage ou toute blessure découlant de ce fait n’est pas couvert par
la garane.
•NE PAS installer l’abri-soleil à côté d’un arbre ou d'un toit incliné. La neige et la glace peuvent glisser sur
l’abri-soleil et causer son effondrement.
Page 20
AVERTISSEMENT :
GARDEZ LES FLAMMES ET AUTRES SOURCES DE CHALEUR À L'ÉCART DE LA TOILE DE TENTE
Cee tente sasfait aux exigences d’inflammabilitéCPAI-84. La toile peut brûler s’il est en contact
permanent avec des flammes. L’applicaon de toute substance étrangère sur la toile de tente pourrait
affecter l’efficacité de ses propriétés de résistance aux flammes.