Uberhaus 38115142 User manual

10’ x 12’ Gazebo
Operators’ Manual p. 2
Abri-soleil 10 x 12 pi
Guide de l'utilisateur p. 11
Model / Modèle : 38115142

IMPORTANT:
1. Keep all children and pets away from assembly area. Children and pets should be
supervised while gazebo is being assembled.
2. The assembled gazebo should be located at least 6 feet (2 m) from any obstruction
such as a fence, garage, house, overhanging branches, laundry lines or electrical wires.
3. This unit is heavy. Do not assemble this item alone. Six people are recommended for
safe assembly.
4. Some parts may contain sharp edges. Wear protective gloves if necessary during
assembly.
5. When assembling and using this product, basic safety precautions should always be
followed to reduce the risk of personal injury and damage to equipment. Please read all
instructions before assembly and use.
6. For outdoor use only. Install on level ground. 16 stakes are provided to secure the
gazebo in the ground. If you wish to secure the pavilion to a wood deck or concrete
surface, use 16 anchors suited for these surfaces (anchors not included).
7. Check all bolts for tightness before and during usage.
8. Please check your state and local regulations prior to purchasing. Some jurisdictions
may require permits for installation and use. Some special procedures may be valid in
your area.
9. While this gazebo is manufactured to withstand winds through only the supplied ground
stakes, securing the gazebo to a deck, concrete patio or a stronger base, in areas subject
to frequent severe weather should be considered.
NOTE: The gazebo’s roof and structure are not guaranteed against extreme weather
conditions (storms, high winds, etc.). If the gazebo is not dismantled for the winter, snow
must be cleaned off regularly. Any damage caused by snow accumulation is not covered
by the warranty.
Care & Maintenance:
Our steel components for garden accessories and furniture are treated with rust inhibiting
paint to protect it from rusting. However, due to the nature of steel, surface oxidation
(rusting) will occur once these protective coatings are scratched. This is not considered a
defect and thus cannot be covered by the warranty.
To minimize this condition, we recommend care when assembling & handling the product
to prevent scratching the paint. Should any scratching or damage occur, we recommend
immediate touch-up with rust inhibiting paint.
Surface rust can also be easily removed with a very light application of regular cooking oil.
If surface oxidation (rusting) occurs and if no measure is taken to prevent this, the
oxidation may drip on to the deck or patio and caused damaging stains, which may be
difficult to remove. This can be prevented if the above-mentioned measures are taken to
keep the product from oxidizing

GAZEBO ASSEMBLY INSTRUCTIONS
Our clear, easy-to-follow, step-by-step instructions will guide you through the
project from start to finish.
All that is required is a screwdriver, a hammer and two ladders of at least 8 feet
(2.5 m) high (not included).
For you safety, DO NOT assemble this item alone. Two people or more are
required for a smooth and safe installation.
Item identification: For ease of identification, all parts are labeled to correspond to
the Step number in which the part is used.

Description Part Quantity Image
Big panel 1 A1 2
Big panel 2 A2 2
Small panel 1 B1 2
Small panel 2 B2 2
Long beam 1 C1 2
Long beam 2 C2 2
Short beam D 2
Lower connector 1 E 4
Lower connector 2 F 6
Top frame G 1
Slanted beam H 4
Middle beam I 6
Long roof piece 1 J1 4
Long roof piece 2 J2 4
Short roof piece 1 J3 4
Short roof piece 2 J4 4
Middle roof piece J5 4
Parts List

Description Part Quantity Image
Small roof piece 1 K1 2
Small roof piece 2 K2 2
Left brace L1 4
Right brace L2 4
Middle brace L3 2
Long brace M1 2
Short brace M2 2
Left rail N1 4
Right rail N2 4
Middle rail N3 2
Center plate O1 6
Corner plate O2 8
Hook P 1
Small top connector Q 1
Cover R 1
Small slanted beam S 4
Long netting tube T 4
Short netting tube U 4
Mosquito netting V 1
Parts List

`
Part Description Quantity Image
AA M6X35 Bolt 4 PCS
BB M6 Flat washer 80 PCS
CC M6X15 Bolt 72 PCS
DD M6X20 Bolt 2 PCS
FF M6 Nut 2 PCS
Z M6 Wrench 2 PCS
Hardware Pack 1
Fig.1: Secure the small panels (B1 and B2) to the big panels (A1 and A2) with bolts (AA) and flat washers (BB).
Fig.2: Secure the lower connector 1 (E) to the corner of the panels with bolts (CC) and flat washers (BB).
Fig.3: Insert the long beam 1 (C1) into the long beam 2 (C2), then secure the long beam 1 (C1) to the long beam 2 (C2)
with bolts (CC), flat washers (BB), bolts (DD) and nuts (FF). Reserve one hole on the long beam 2 (C2) to assemble the
netting tube.

Part Description Quantity Image
BB M6 Flat washer 38 PCS
CC M6X15 Bolt 18 PCS
DD M6X20 Bolt 20 PCS
Hardware Pack 2
Fig.7: Secure the top end of the slanted beam (H) to the top frame (G) with bolts (DD) and flat washers (BB).
Fig.8: Secure the slanted beam (H) to the lower connector 1 (E) with bolts (CC) and flat washers (BB).
Fig.9: Secure the middle beam (I) to the top beams (G) with bolts (DD) and flat washers (BB).
Fig.10: Secure the lower end of the middle beam (I) the lower connector 2 (F) with bolts (CC) and flat washers (BB).
Fig.4: Secure the assembled long beam 1 to the big panels (A1 and A2) with bolts (CC) and flat washers (BB). Repeat this step to
secure the short beam (D) to the small panels (B1 and B2).
Fig.5: Secure the lower connector 2 (F) and short netting tube (U) to the short beam (D) with bolts (CC) and flat washers (BB).
Fig.6: Secure the long netting tubes (T) to the long beams (C1 and C2) with bolts (CC) and flat washers (BB). Repeat this step to
secure the short netting tubes.

\
Fig.11: Secure the small slanted beam (S) to the top frame (G) with bolts (CC) and flat washers (BB).
Fig.12: Secure the small slanted beam (S) to the small top connector (Q) with bolts (CC) and flat washers (BB).
Fig.13: Attach the hook (P) to the small top connector (Q).
Part Description Quantity Image
AA M6X35 Bolt 2PCS
BB M6 Flat washer 16 PCS
EE M6X15 Screw 14 PCS
Hardware Pack 3
Fig.14: Insert the small roof pieces (K1 and K2) into the rail on the small slanted beam (S).
Fig.15: Insert the brace (M1 and M2) into the lower of the small roof piece (K1 and K2), then secure the corner
plate (O2) to the small slanted beam (S) through three holes with screws (EE) and flat washers (BB).
Fig.16: Secure the cover (R) to the small top connector (Q) with bolts (AA) and flat washers (BB).

Fig.17: Insert the short roof piece 1 (J3) and short roof piece 2 (J4) into the middle beam (I) and slanted beam (H), then
insert the rails (N1 and N2) into it. Insert the long roof piece (J1) into the middle beam (I) and slanted beam (H). Repeat this
step to install the right roof pieces.
Fig.18: Insert the middle roof piece (J5) into the middle beam (I); then insert the middle rail (N3) into it. Insert the middle roof
piece (J5) into the middle beam (I).
Fig.19: Insert the braces (L1, L2 and L3) into the lower roof pieces; then secure the center plate (O1) to the middle beam (I)
through three holes with screws (EE) and flat washers (BB).
Fig.20: Fig.20: Secure the corner plate (O2) to the slanted beam (H) through three holes with screws (EE) and flat washers
(BB).
Part Description Quantity Image
GG Ring 52 PCS
Hardware Pack 4
Part Description Quantity Image
HH Φ8X180mm Stake 16 PCS
Hardware Pack 5

Fig.21: Attach the mosquito netting (V) to the long netting tubes (T) and short tubes (U) with rings (GG).
Fig.22: Secure the whole gazebo to the ground with stakes (HH).
Your gazebo is now fully assembled.