Uberhaus SWING BED L-GZ347PST-WTN User manual

ASSEMBLY INSTRUCTIONS
SWING BED
RONA CODE: 38115042
ITEM# L-GZ347PST-WTN

A Top Connection 1 Q Hook 2
B Beam for big
roof 4
R Small canopy 1
C Long beam 2
S Large canopy 1
D Short beam 2
T Bolster 2
E1 Post 1 1 U Big pillow 2
E2 Post2 1 V Small pillow 1
E3 Post 3 1
W Cushion 1
E4 Post 4 1 X Bib 2
F Middle beam 1 AA 5/16”-18*2.125
Bolts
4
G Back rail 1
BB 5/16”-18*0.75
Bolts
12
H Side rail 2
CC 5/16”-18
Nuts
8
I Front supporter 1 DD 5/16”-18*1.75
Bolts
4
J Back supporter 1 EE 1/4”-20*1.4
Bolts
4
K Seat frame 1
FF 1/4”-20*1.25
Bolts
6
L Back frame 1
GG 1/4”-20
Nuts
6
M1 Left arm 1
HH 3/16”-24*0.4
Bolts
4
M2 Right arm 1
II Nails 5/16"*7 8
N Adjusting bar 1
JJ Allen key 1/4”-20 1
O Suspender 4 KK Wrench
1/4”-20/5/16”-18
1
P Latch 4
MM Bolts 1/4"-20*2 2
PP Bolts
(preassembled)
2 NN Plastic washer 2
Parts List

（1） Connect middle beam (F) to short beam (D) with bolts (AA), nuts (CC). ( Fig.1)
（2） Insert the each side of long beam (C) into the top hold of post 1(E1), post 2(E2), post 3 (E3), post 4 (E4), and
then insert short beam (D) into the top hold of post 1(E1), post 2(E2), post 3 (E3), post 4 (E4). (Fig.2)
（3） Tighten side rail (H) onto post 1 (E1), post 2 (E2), post 3 (E3), post 4 (E4) with bolts (BB). ( Fig.2)
（4） Tighten back rail (G) onto post 1 (E1), post 4 (E4) with bolts (BB). ( Fig.4)
Step1:

（5） Insert one of side of beam for big roof (B) into the hole of top connection (A). (Fig.5)
（6） Spread the small canopy (R) and large canopy (S), don’t spread the large canopy fully at this time (Fig.6)
（7） Screw beam of big roof (B) and post1 (E1), post 2 (E2), post 3 (E3), post 4 (E4) with bolts (EE), nuts (GG).
(Fig7)
Step 2:

（8） Connect front supporter (I), left arm (M1) and right arm (M2) with bolts (FF). (Fig8)
（9） Connect back supporter (J), left arm (M1) and right arm (M2) with bolts (FF). (Fig9)
（10） Tighten seat frame (K) and back frame (L) with bolts (DD), nuts (CC). (Fig10)
（11） Connect seat frame (K), left arm (M1) and right arm (M2) with bolts (DD), plastic washer (NN),nuts (CC).
(Fig11)
（12）Tighten back frame (L) with the bolts (PP). (Fig12) Note: Do this step only if you will use this unit as a
bed.
Step 3:

（13）Connect seat frame adjusting bar (N) and back frame (L) with bolts (MM), nuts (GG). (Fig13)
（14）Lay the adjustable support of the adjusting bar (N) on the back supporter (J). (Fig14)
（15）Hang one of the side of suspender (O) onto the hooks of arm left (M1) and arm right (M2). (Fig15)
Step 4:

（16）Fix one side of suspender (O) onto hook (Q), the other side onto middle beam (F,) then cover hook (Q) with bib
(X). (Fig.16)
(17) Place swing cushion (W) and bolster (T), big pillow (U) small pillow (V) on the seat and back.
(18) Spread the large canopy (S) fully.
(19) Secure the post 1 (E1), post 2 (E2), post 3 (E3), post 4 (E4), using nails (II) to fasten the product. (Fig.19)
(20) Fasten latch (P) and side rail (H) with bolts (HH). (Fig.20)
Maintenance:
1. This swing bed is not a permanent structure and should be disassembled & stored away after use.
2. Do not repack your swing bed until it is completely dry.
3. This swing bed must be assembled by two adults or more.
4. This swing bed must not be left erect in high wind conditions.
Made in China
Step 5:

INSTRUCTIONS DE MONTAGE
LIT-BALANÇOIRE
CODE RONA: 38115042
ARTICLE No. L-GZ347PST-WTN

A Connexion du toit 1 Q Crochet 2
B Poutre du grand
Toit
4 R Petit auvent 1
C Poutre longue 2 S Grand auvent 1
D Poutre courte 2
T Polochon 2
E1 Poteau 1 1 U Grand coussin 2
E2 Poteau 2 1 V Petit coussin 1
E3 Poteau 3 1 W Coussin de
balançoire
1
E4 Poteau 4 1 X Tablier 2
F Poutre centrale 1 AA Boulons
5/16”-18*2.125
4
G Balustre arrière 1
BB Boulons
5/16”-18*0.75
12
H Balustre latéral 2
CC Écrous 5/16”-18 8
I Support avant 1 DD Boulons
5/16”-18*1.75
4
J Support arrière 1 EE Boulons
1/4”-20*1.4
4
K Cadre du siège 1
FF Boulons
1/4”-20*1.25
6
L Cadre du dossier 1
GG Écrous 1/4”-20 6
M1 Accoudoir gauche 1
HH Boulons
3/16”-24*0.4
4
M2 Accoudoir droit 1
II Clous 5/16"*7 8
N Barre
d’ajustement
1
JJ Clé (Allen.)
1/4”-20
1
O Suspente 4 KK Clé
1/4”-20/5/16”-18
1
P Loquet 4
MM Boulons 1/4"-20*2 2
PP Boulons
(préassemblées)
2 NN Plates 2
Liste de pièces

1. Connectez la poutre centrale (F) à la poutre courte (D) avec des boulons (AA), et écrous (CC). (Fig.1)
2. Introduisez chaque extrémité de la poutre longue (C) dans les connexions supérieures du poteau 1 (E1), poteau
2 (E2), poteau 3 (E3), poteau 4 (E4), et puis Introduisez chaque extrémitéde la poutre courte (D) dans les
connexions supérieures du poteau 1 (E1), poteau 2 (E2), poteau 3 (E3), poteau 4 (E4), (Fig.2)
3. Fixez le balustre latéral (H) au poteau 1 (E1), poteau 2 (E2), poteau 3 (E3), poteau 4 (E4) avec des boulons (BB)
(Fig.2).
4. Fixez le balustre arrière (G) au poteau 1 (E1), et poteau 4 (E4) avec des boulons (BB) (Fig.4).
Étape 1: