Unverferth RIPPER-STRIPPER 332 User manual
Seedbed Tillage
RIPPER-STRIPPER®
Strip-Till Subsoilers
Rigid & Folding Flex Frame
Models 332 & 312
Beginning with Serial Number A62580100
Part No. 68907
2
RIPPER-STRIPPER — Introduction
This symbol identifies important safety messages. When you see it, read the message
that follows and be alert to the possibility of personal injury.
Remember, safety instructions stated in this manual are for your protection. Read them
carefully and follow them closely when working around or using this machine.
Read and study this manual completely before attempting to operate this implement. Take this
manual to the field for handy reference when operating, adjusting, or servicing your machine.
When referenced, “Right-Hand” (RH) and “Left-Hand” (LH) side of the machine are determined
by standing behind the machine and facing in the direction of travel.
Foreword
¨ Wheel bolts tightened (recheck after
initial use)
¨ Tire pressures checked
¨ Hardware tightened
¨ Machine lubricated
¨ Safety and operating procedures re-
viewed
¨ Field adjustment information reviewed
¨ Warranty information reviewed
¨ Hydraulic hoses properly routed/fittings
tight
Pre-Operation Checklist
3
RIPPER-STRIPPER — Introduction
Product Information
The information, specifications, and illustrations in the manual are on the basis of information avail-
able at the time it was written. Due to continuing improvements in the design and manufacture
of Unverferth products, all specifications and information contained herein are subject to change
without notice.
FIG. 1
When ordering parts or when requesting further information or assistance, always give the
following information:
• Machine name
• Serial number
All products manufactured by Unverferth Mfg. Co., Inc. are warranted to be free from ma-
terial and workmanship
defects for one full year from time of consumer delivery. Your local
dealer will gladly assist you with any warranty questions.
Please fill out and retain this portion for your records. The serial number plate is located
on the frame as shown below.
Purchase Date _______________ Model _______________ Serial No. _________________________
Dealer ________________________________________ City ________________________________________
Dealer Contact _____________________________________ Phone ________________________________
4
RIPPER-STRIPPER — Introduction
Foreword........................................................................................................................................2
Pre-Operation Checklist..................................................................................................................2
Product Information........................................................................................................................3
SECTION I
Safety
General Hazard Information....................................................................................................... 1-2
Safety Decals............................................................................................................................. 1-3
Following Safety Instructions..................................................................................................... 1-4
Before Servicing......................................................................................................................... 1-4
Before Operating........................................................................................................................ 1-5
During Operation........................................................................................................................ 1-5
Before Transporting.................................................................................................................... 1-5
During Transport......................................................................................................................... 1-6
Pressurized Oil........................................................................................................................... 1-6
Preparing for Emergencies......................................................................................................... 1-7
Wearing Protective Equipment................................................................................................... 1-7
Table Of Contents
5
RIPPER-STRIPPER — Introduction
Table Of Contents
SECTION II
Set Up
Folding Wing Extension Assembly.............................................................................................. 2-2
Combo® Coulter Blade............................................................................................................... 2-4
Support Stand............................................................................................................................ 2-5
Optional 4-Coulter Per Row (64776B)....................................................................................... 2-6
Recommended Set Up For Units With Rolling Basket.............................................................. 2-7
Potential Set Up For Units With Press Wheels......................................................................... 2-9
Stabilizer Wheel Assembly....................................................................................................... 2-10
Panel Reector Assembly......................................................................................................... 2-12
Outer Reector Assemblies............................................................................................... 2-12
Center Reector Assemblies & SMV Emblem................................................................... 2-16
Hydraulics Set Up
Folding 8 Shank 30”, 36”, 38”, & 40” Spacing............................................................. 2-20
Folding 12 Shank 30” Spacing........................................................................................ 2-25
Folding 12 Shank 36”, 38” & 40”, 16 Shank 30” Spacing........................................... 2-28
Hydraulics Set Up Flex Optional.............................................................................................. 2-33
Purging Hydraulic System........................................................................................................ 2-37
Optional Attachments............................................................................................................... 2-38
Strip-Builder Options................................................................................................................ 2-39
Relocation For Strip-Builder Coulters On 12-Row 30” & 16-Row 30”
............................ 2-39
Procedure For Reversing Rear Coulters on Optional Strip-Builders (All Units)................ 2-41
Zone Firmer (65249B) With Lead Angled Press Wheel & 4-Wheel Press Wheel &
Zone-Firmer (68957B) With Lead Angled Press Wheel & 5 Wheel Press Wheel..... 2-42
4-Wheel Zone Firmer (68082B)........................................................................................ 2-43
5-Wheel Scrapper Kit (67182B); 4-Wheel Scraper Kit (65264B);
4-Wheel Scraper Kit (68083B)................................................................................... 2-45
Liquid Fertilizer Attachment Complete (65332B) With Shank Protector Plates................ 2-46
Dry RH Fertilizer Attachment Complete (67652B) With Shank Protector Plates.............. 2-47
Shank Protectors............................................................................................................... 2-48
16” Stagger Kits (66952B)................................................................................................ 2-49
7” Shatter Wings (67691B) or 9” Shatter Wings (67692B)............................................. 2-50
Overhead Layouts..................................................................................................................... 2-51
Optional Floating Row Cleaner................................................................................................ 2-65
FOR 12 SHANK 36” SPACING MODEL 332 RIPPER-STRIPPER,
WING FOLD MODIFICATION KIT #69595B
PLEASE REFER TO YOUR INSTRUCTION SHEET #69594.
6
RIPPER-STRIPPER — Introduction
Table Of Contents
SECTION III
Operation
General Operation Information................................................................................................... 3-2
Preparing Tractor........................................................................................................................ 3-3
Front-End Weights............................................................................................................... 3-3
Horsepower Requirements................................................................................................... 3-3
Sway Blocks........................................................................................................................ 3-3
Wheel Spacing..................................................................................................................... 3-3
Drawbar Position................................................................................................................. 3-3
Attaching To Tractor................................................................................................................... 3-4
Mast And Hitch................................................................................................................... 3-4
Bolts And Nuts.................................................................................................................... 3-4
Pins And Retaining Rings.................................................................................................... 3-4
Pin Assembly (67188B & 67187B)..................................................................................... 3-5
Tractor Without Quick Attach Coupler................................................................................. 3-6
Tractor With Quick Attach Coupler...................................................................................... 3-8
Folding Wings............................................................................................................................. 3-9
Transporting.............................................................................................................................. 3-10
Unhitching From Tractor........................................................................................................... 3-10
Leveling Frame......................................................................................................................... 3-11
Side-To-Side Leveling........................................................................................................ 3-11
Front-To-Rear Leveling....................................................................................................... 3-11
Leveling Wings (8-30”,36”,38”,40” & 12-30”,36”,38”,40”)
Adjustment Procedures...................................................................................................... 3-12
Adjusting Cylinder Clevis End........................................................................................... 3-13
Unfolding Wings....................................................................................................................... 3-14
Flex Hydraulic (Optional) — Field Operation.......................................................................... 3-15
Preparing Implement................................................................................................................ 3-18
Depth of Penetration......................................................................................................... 3-18
Support Stand.......................................................................................................................... 3-19
Shanks..................................................................................................................................... 3-20
Horizontal Adjustment (All Models).................................................................................... 3-20
Re-Setting a Tripped Shank.............................................................................................. 3-20
Lower Pull Arm (Model 332)............................................................................................ 3-21
Toggle Shim (Auto-Reset — For Model 332 Only).......................................................... 3-21
Coulters.................................................................................................................................... 3-22
Combo Coulter................................................................................................................... 3-22
Vertical Position................................................................................................................. 3-22
Procedure For Reversing Rear Coulters............................................................................ 3-23
Rear Coulter...................................................................................................................... 3-24
Rear Coulter Spring Pressure........................................................................................... 3-24
Working Depth................................................................................................................... 3-24
Optional Attachments............................................................................................................... 3-25
7
RIPPER-STRIPPER — Introduction
Table Of Contents
SECTION IV
Maintenance
Daily Service
Beginning of Day................................................................................................................ 4-2
End of Day.......................................................................................................................... 4-2
Annual Service
Beginning of Season........................................................................................................... 4-3
End of Season..................................................................................................................... 4-3
Complete Torque Chart.............................................................................................................. 4-4
Hydraulic Fittings....................................................................................................................... 4-4
Wheels and Tires
Wheel Nut Torque................................................................................................................ 4-5
Tire Pressure....................................................................................................................... 4-5
Tire Warranty....................................................................................................................... 4-6
Lubrication Points....................................................................................................................... 4-7
Troubleshooting
Poor Penetration.................................................................................................................. 4-8
Plugging............................................................................................................................... 4-8
Implement Running Crooked In Field.................................................................................. 4-8
Shanks Not Resetting Into Ground After Tripping.............................................................. 4-9
Shank Leading Off Row Center.......................................................................................... 4-9
Excessive Soil Disturbance.................................................................................................. 4-9
Shank Replacement
Wear Bar Replacement...................................................................................................... 4-10
Shovel Replacement.......................................................................................................... 4-10
Shank Tip Replacement..................................................................................................... 4-10
Shank Replacement - Model 332........................................................................................... 4-11
Shank Spring..................................................................................................................... 4-11
Shear Bolt - Model 312 ........................................................................................................ 4-12
Shear-Bolt Replacement.................................................................................................... 4-12
Auto-Reset Shank Toggle Replacement - Model 332............................................................. 4-13
Combo Coulter Spring Replacement All Models...................................................................... 4-14
Hub Adjustment and Replacement For Combo Coulters and Rear Coulters.......................... 4-15
Replacing Bearings in Rolling Harrow Baskets....................................................................... 4-19
Adjusting Wing Down Pressure In The Field.......................................................................... 4-20
Optional Row Cleaner Adjustments.......................................................................................... 4-21
Tooth Wheel Hub Adjustment and Replacement..................................................................... 4-22
8
RIPPER-STRIPPER — Introduction
Table of Contents
SECTION V
Parts
Rigid Main Frame – 2 & 4 Shank........................................................................................... 5-2
Rigid Main Frame – 6 & 8 Shank........................................................................................... 5-4
Folding Main Frame - 6 & 8 Shank........................................................................................ 5-6
Folding Main Frame — 12 Shank 30” Spacing.................................................................... 5-10
Folding Main Frame — 12 Shank 36”/38”/40” Spacing & 16 Shank................................. 5-12
Stabilizer Wheel....................................................................................................................... 5-16
Auto-Reset Shank - Model 332.............................................................................................. 5-18
Shear-Bolt Shank - Model 312 ............................................................................................. 5-22
Combo Lead Coulter................................................................................................................ 5-24
Flush Clamps........................................................................................................................... 5-28
Optional Floating Row Cleaner Components........................................................................... 5-30
Quad-Coulter Option #64776B................................................................................................. 5-32
Shank Attachments.................................................................................................................. 5-34
Shank Attachment Frame & Arm Assembly............................................................................ 5-36
Strip-Builder Components......................................................................................................... 5-38
4 & 5 Wheel Zone-Firmer Components.................................................................................. 5-40
4 Wheel Zone-Firmer & Front Press Wheel Components....................................................... 5-42
Front Press Wheel Components............................................................................................... 5-44
Rolling Harrow Basket Components........................................................................................ 5-46
Storage Stand.......................................................................................................................... 5-48
Standard Folding Hydraulic Components - 8 Wide................................................................. 5-50
Flex Folding Hydraulic Components - 8 Wide........................................................................ 5-52
Standard Folding Hydraulic Components - 12 Narrow........................................................... 5-54
Hydraulics - Standard Wing Version for Flex Frame Machines
Serial #A65700217 and Higher......................................................................................... 5-56
Hydraulics - Standard Wing Version for Flex Frame Machines
Prior to Serial #A65700217.............................................................................................. 5-58
Flex Folding Hydraulic Kit
12 Wide/16 Narrow Beginning with Serial Number A65700217...................................... 5-60
Flex Fold Hydraulic Components
12 Wide/16 Narrow Prior to Serial Number A65700217................................................. 5-62
Fertilizer Attachments............................................................................................................... 5-64
Reector & Lighting Components............................................................................................ 5-66
FOR 12 SHANK 36” SPACING MODEL 332 RIPPER-STRIPPER,
WING FOLD MODIFICATION KIT #69595B
PLEASE REFER TO YOUR INSTRUCTION SHEET #69594.
1-1
RIPPER-STRIPPER — Safety
SECTION I
Safety
General Hazard Information....................................................................................................... 1-2
Safety Decals............................................................................................................................. 1-3
Following Safety Instructions..................................................................................................... 1-4
Before Servicing......................................................................................................................... 1-4
Before Operating........................................................................................................................ 1-5
During Operation........................................................................................................................ 1-5
Before Transporting.................................................................................................................... 1-5
During Transport......................................................................................................................... 1-6
Pressurized Oil........................................................................................................................... 1-6
Preparing for Emergencies......................................................................................................... 1-7
Wearing Protective Equipment................................................................................................... 1-7
RIPPER-STRIPPER — Safety
General Hazard Information
1-2
No accident-prevention program can be successful without the wholehearted cooperation of
the person who is directly responsible for the operation of the equipment.
A large number of accidents can be prevented only by the operator anticipating the result
before the accident is caused and doing something about it. No power-driven equipment,
whether it be transportation or processing, whether it be on the highway, in the field, or in
the industrial plant, can be safer than the person who is at the controls. If accidents are
to be prevented--and they can be prevented--it will be done by the operators who accept
the full measure of their responsibility.
It is true that the designer, the manufacturer, and the safety engineer can help; and they will
help, but their combined efforts can be wiped out by a single careless act of the operator.
It is said that, “the best kind of a safety device is a careful operator.” We, at Unverferth
Mfg. Co., Inc. ask that you be that kind of operator.
REMEMBER:
THINK SAFETY
A CAREFUL OPERATOR IS THE
BEST INSURANCE AGAINST AN
ACCIDENT!
SIGNAL WORDS
INDICATES AN EXTREMELY HAZARDOUS SITUATION OR ACTION THAT WILL RESULT IN
SERIOUS INJURY OR DEATH.
INDICATES A HAZARDOUS SITUATION OR ACTION THAT COULD RESULT IN SERIOUS IN-
JURY OR DEATH.
INDICATES AN UNSAFE SITUATION OR ACTION THAT MAY RESULT IN PERSONAL INJURY.
Is used for instruction on operating, adjusting, or servicing a machine.
1-3
RIPPER-STRIPPER — Safety
DECALS. THESE DECALS INFORM AND REMIND THE OPERATOR WITH OPERATIONAL
INFORMATION AND SAFETY MESSAGES.
Safety Decals
PART NO. 95445 PART NO. 99507
PART NO. 902221 PART NO. 97048 PART NO. 97337
PART NO. 97973 PART NO. 97972
PART NO. 99850
PART NO. 97961
PART NO. 900558
RIPPER-STRIPPER — Safety
• Read and understand this operator’s manual before operating.
• All machinery should be operated only by trained and authorized personnel.
• To prevent machine damage, use only attachments and service parts approved by the
manufacturer.
• Always shut tractor engine off and remove key before servicing.
• Avoid personal attire such as loose tting clothing, shoestrings, drawstrings, pants cuffs,
long hair, etc., that may become entangled in moving parts.
• Do not allow anyone to ride on the implement. Make sure everyone is
clear before operating machine or towing vehicle.
• When working around sweeps and points, be careful not to be cut by sharp edges.
• Never attempt to operate implement unless you are in driver's seat.
• Avoid working under an implement; however, if it becomes absolutely un-
avoidable, make sure the implement is safely blocked.
• Ensure that all applicable safety decals are installed and legible.
• When working around the implement, be careful not to be cut by sharp edges.
• Explosive separation of a tire and rim can cause serious injury or death. Only properly
trained personnel should attempt to service a tire and wheel assembly.
• Add sufcient ballast to tractor to maintain steering and braking control at all times. Do
not exceed tractor's lift capacity or ballast capacity.
Following Safety Instructions
Before Servicing
1-4
• Regulate speed to eld conditions. Maintain complete control at all times.
• Never service or lubricate equipment when in operation.
• Keep away from overhead power lines. Electrical shock can cause serious
injury or death.
• Use extreme care when operating close to ditches, fences, or on hillsides.
• Do not leave towing vehicle unattended with the engine running.
During Operation
• Install transport locks before transporting.
• Check for proper function of all available transport lights. Make sure that all reectors
are clean and in place on machine. Make sure that the SMV emblem and SIS decal are
visible to approaching traffic.
Before Transporting
• Do not stand between towing vehicle and implement during hitching.
• Always make certain everyone and everything is clear of the machine before beginning
operation.
• Verify that all safety shields are in place and properly secured.
• Ensure that all applicable safety decals are installed and legible.
• Add sufcient ballast to tractor to maintain steering and braking control at all times. Do
not exceed tractor's lift capacity or ballast capacity.
• Inspect elds for buried utility lines (electric, natural gas, water, etc.). To nd buried lines
in the US or Canada contact 1-888-258-0808, in the US you may also contact 811.
Before Operating
1-5
RIPPER-STRIPPER — Safety
RIPPER-STRIPPER — Safety
Pressurized Oil
• Relieve pressure before disconnecting hydraulic lines from tractor, loosening any hydraulic
fittings or servicing hydraulic system. See hydraulic power unit manual for procedure to
relieve pressure.
• High-pressure uids can penetrate the skin and cause serious injury or
death. Use cardboard or wood to detect leaks in the hydraulic system.
Seek medical treatment immediately if injured by high-pressure uids.
• Hydraulic system must be purged of air before operating to prevent serious injury or
death.
• Do not bend or strike high-pressure lines. Do not install bent or damaged tubes or hoses.
• Repair all oil leaks. Leaks can cause res, personal injury, and environmental damage.
• Route hoses and lines carefully to prevent premature failure due to kinking and rubbing
against other parts. Make sure that all clamps, guards and shields are installed correctly.
• Check hydraulic hoses and tubes carefully. Replace components as necessary if any of
the following conditions are found:
- End fittings damaged, displaced, or leaking.
- Outer covering chafed/cut or wire reinforcing exposed.
- Outer covering ballooning locally.
- Evidence of kinking or crushing of the flexible part of a hose.
• Comply with all laws governing highway safety when moving machinery.
• Use transport lights as required by all laws to adequately warn operators of other vehicles.
• Use good judgement when transporting equipment on highways. Regulate speed to road
conditions and maintain complete control.
• Maximum speed of implement should never exceed 20 mph. Do not exceed 10 mph
during off-highway travel.
• Slow down before making sharp turns to avoid tipping. Drive slowly over rough ground
and side slopes.
• It is probable that this implement is taller, wider and longer than the towing vehicle. Be-
come aware of and avoid all obstacles and hazards in the travel path of the equipment,
such as power lines, ditches, etc.
During Transport
1-6
• Keep a rst aid kit and properly rated re extinguisher nearby.
• Keep emergency numbers for re, rescue, and poison control personnel
near the phone.
• Wear clothing and personal protective equipment appropriate for the job.
• Wear steel-toed shoes when operating.
• Wear hearing protection when exposed to loud noises.
• Do not wear additional hearing impairing devices such as radio headphones, etc.
Preparing for Emergencies
Wearing Protective Equipment
1-7
RIPPER-STRIPPER — Safety
RIPPER-STRIPPER — Safety
Notes
1-8
2-1
RIPPER-STRIPPER — Set Up
SECTION II
Set Up
Folding Wing Extension Assembly.............................................................................................. 2-2
Combo Coulter Blade................................................................................................................. 2-4
Support Stand............................................................................................................................ 2-5
Optional 4-Coulter Per Row (64776B)....................................................................................... 2-6
Recommended Set Up For Units With Rolling Basket.............................................................. 2-7
Potential Set Up For Units With Press Wheels......................................................................... 2-9
Stabilizer Wheel Assembly....................................................................................................... 2-10
Panel Reector Assembly......................................................................................................... 2-12
Outer Reector Assemblies............................................................................................... 2-12
Center Reector Assemblies & SMV Emblem................................................................... 2-16
Hydraulics Set Up
Folding 8 Shank 30”, 36”, 38”, & 40” Spacing............................................................. 2-20
Folding 12 Shank 30” Spacing........................................................................................ 2-25
Folding 12 Shank 36”, 38” & 40”, 16 Shank 30” Spacing........................................... 2-28
Hydraulics Set Up Flex Optional.............................................................................................. 2-33
Purging Hydraulic System........................................................................................................ 2-37
Optional Attachments............................................................................................................... 2-38
Strip-Builder Options................................................................................................................ 2-39
Relocation For Strip-Builder Coulters On 12-Row 30” & 16-Row 30”
............................ 2-39
Procedure For Reversing Rear Coulters on Optional Strip-Builders (All Units)................ 2-41
Zone Firmer (65249B) With Lead Angled Press Wheel & 4-Wheel Press Wheel &
Zone-Firmer (68957B) With Lead Angled Press Wheel & 5 Wheel Press Wheel..... 2-42
4-Wheel Zone Firmer (68082B)........................................................................................ 2-43
5-Wheel Scrapper Kit (67182B); 4-Wheel Scraper Kit (65264B);
4-Wheel Scraper Kit (68083B)................................................................................... 2-45
Liquid Fertilizer Attachment Complete (65332B) With Shank Protector Plates................ 2-46
Dry RH Fertilizer Attachment Complete (67652B) With Shank Protector Plates.............. 2-47
Shank Protectors............................................................................................................... 2-48
16” Stagger Kits (66952B)................................................................................................ 2-49
7” Shatter Wings (67691B) or 9” Shatter Wings (67692B)............................................. 2-50
Overhead Layouts..................................................................................................................... 2-51
Optional Floating Row Cleaner................................................................................................ 2-65
FOR 12 SHANK 36” SPACING MODEL 332 RIPPER-STRIPPER,
WING FOLD MODIFICATION KIT #69595B
PLEASE REFER TO YOUR INSTRUCTION SHEET #69594.
2-2
RIPPER-STRIPPER — Set Up
NOTE: For proper positioning, refer to “Overhead Layouts” in this section.
THE MACHINE AT ANY TIME WHILE BEING HOISTED. BE SURE ALL LIFTING DEVICES
AND SUPPORTS ARE RATED FOR THE LOADS BEING HOISTED. THESE ASSEMBLY
LOAD RATINGS FOR INDIVIDUAL LOADS WILL BE GIVEN AT THE APPROPRIATE TIME
IN THE INSTRUCTIONS.
MUST BE WORN WHILE SERVICING IMPLEMENT.
1. Raise frame approximately 38” from the
ground with a safe lifting device rated for
5,000 lbs. so that support stands can be
positioned under the frame to support the
weight (FIG. 2-1).
2. Secure a 1000 lbs. min. lifting device to the
end of the base wing. Remove the shipping
brace and lower the wings so they are level
with the main frame.
FIG. 2-1
Folding Wing Extension Assembly
2-3
RIPPER-STRIPPER — Set Up
FIG. 2-2
Shim
(67869)
Left-Hand
Extension Frame
Wing Weldment
Right-Hand
Extension Frame
Wing Weldment Right-Hand Wing
Base Weldment
Shim
(67868)
3/4"-10UNC x 2"
Capscrews (9390-145)
& 3/4"-10UNC
Locknuts (9802)
Folding Wing Extension Assembly (continued)
NOTE: Use shims (67868 and 67869) in between the wing and wing extension for proper
leveling (FIG. 2-2). Also see OPERATION section for frame and wing leveling.
8, 12, & 16 Shank
3. Attach safe lifting device rated at 4,000 lbs. minimum to the wing extensions while they
are bolted together. Attach the entire assembly to the right-hand base wing. Secure with
eight 3/4”-10UNC x 2” long capscrews and locknuts (FIG. 2-2).
bolted to the machine. The 1-piece mount-
ing plate should be positioned away from
4. Reattach the safe lifting device to the left-
hand wing.
• THE EXTENSION COULD BECOME UN-
STABLE IF RESTING ON THE GROUND.
Shim
(67868)
Shim (67869)
Lock Nuts (9802)
Capscrews (9390-145)
Extension
Base
Weldment
2-4
RIPPER-STRIPPER — Set Up
• BE CAREFUL WHEN WORKING AROUND
COULTER BLADES. FAILURE TO DO SO
COULD RESULT IN PERSONAL INJURY
DUE TO THE SHARP EDGES.
1. Install coulter blades to hub using 3/8”-16 x
1 1/4” lg. capscrews (9390-056) and locknut
(9928) (FIG. 2-5). Refer to “Torque Chart” in
MAINTENANCE section.
FIG. 2-5
Combo Coulter Blade
5. Attach the left-hand extension to the left-side using seven 3/4”-10UNC x 2” capscrews
(9390-145), one 3/4”-10UNC x 2 1/2” capscrew (9390-147) and eight 3/4”-10UNC locknuts
(9802). See FIG. 2-2 for reference. Add shims (67868 and 67869) between wings and wing
extensions for proper leveling (FIG. 2-3).
6. Remove the four 3/4”-10UNC hex jam nuts (9395-016) which secures the right-hand ex-
tension to the stand and discard nuts and shipping stand.
Folding Wing Extension Assembly (continued)
This manual suits for next models
1
Table of contents
Other Unverferth Farm Equipment manuals
Unverferth
Unverferth Killbros 200 Series User manual
Unverferth
Unverferth 9250 User manual
Unverferth
Unverferth AWS-30 User manual
Unverferth
Unverferth 530 User manual
Unverferth
Unverferth 632 User manual
Unverferth
Unverferth PARKER Seed Chariot 2620 User manual
Unverferth
Unverferth BRENT V1100 User manual
Unverferth
Unverferth Rolling Harrow II User manual
Unverferth
Unverferth BLU-JET SubTiller 4 User manual
Unverferth
Unverferth EQUALIZER B35190100 User manual
Unverferth
Unverferth CROSS-FOLD ROLLING HARROW 1645 User manual
Unverferth
Unverferth BLU-JET Legacy NH3 User manual
Unverferth
Unverferth BRENT 678 User manual
Unverferth
Unverferth PARKER Seed Chariot 1020 User manual
Unverferth
Unverferth Killbros 1135 User manual
Unverferth
Unverferth Killbros 1950 User manual
Unverferth
Unverferth 1000 User manual
Unverferth
Unverferth BLU-JET TrenchMaster User manual
Unverferth
Unverferth BLU-JET SubTiller II User manual
Unverferth
Unverferth CROSS-FOLD ROLLING HARROW 1645 User manual
