Uplift Desk CHR454 User manual

®
UPLIFT Motion Stool
CHR454
UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Step 1
The Cylinder (part 3) comes with a plastic cap which protects the gas-release
button during shipment. Remove this plastic cap from the end of the Cylinder,
and dispose of it.
Step 2
Place the larger end of the Neck (part 2) over the bottom of the Seat (part 1).
Press rmly until you feel it snap into place. If there is a gap around just half
of where the parts join, press down rmly again in that direction to assure
that the pieces have been joined completely.
Step 3
REMINDER: Ensure that the plastic cap from Step 1 has been removed from
the Cylinder. Leaving this on may damage stool during assembly.
Slip the larger end of the Cylinder (part 3) into the hole on the Base (part 4).
Then, afx the Seat (part 1) and Neck (part 2) assembly to the top
of the Cylinder (part 3).
Step 4
Seat height is adjusted by pressing one of the 2 levers found on either side
of the seat.
The stool’s weighted convex base enables you to move freely while sitting
or perching. The weighted base keeps it upright when not in use. A treaded
rubber covering on the weighted base maximizes friction with the oor.
You can perch sit with the stool tilted forward or rock back and forth. This
stool allows motion in every direction. That’s why we call it UPLIFT Motion.
The fabric seat provides maximum breathability. This isn’t a hot seat after
all, it’s made for comfort. Keeps you dry; it’s no sweat!
The soft foam padded seat cushion with waterfall edge reduces pressure
points and allows maximum exibility. There’s a reason most stools are round.
Package Contents:
Part 1
Seat
Part 3
Cylinder
Part 2
Neck
Part 4
Base
CHR454/R02

IMPORTANT NOTES
!
!
!
!
!
!
!
!
!
!
!
!
!
If components are damaged or missing, contact UPLIFT Desk immediately. DO NOT
use substitute parts. Use only UPLIFT Desk replacement parts. The use of non-UPLIFT
Desk parts could cause personal injury, property damage, and void the warranty.
To avoid falling or tipping, have someone help you until you know the balance points
of your Motion Stool and how to avoid tipping. Do not put downward weight on one
side of the Motion Stool. If you must reach or lean, shift your weight to do so. Ask for
help or use a device to extend your reach. Never try to reach an object if you must
move forward in your seat and your buttocks do not stay in full contact with the seat.
Never lean backward to reach an object.
Read all instructions before assembly. Failure to assemble properly may result in dam-
age or personal injury
UPLIFT Desk assumes no responsibility for any damage or injury caused by improper
assembly or use of this product.
Always ensure Motion Stool is securely positioned during use. For proper balance and
stability, always sit on the middle of the seat.
If you do not understand any part of these warnings, cautions, or instructions, contact
UPLIFT Desk for direction in the use of this product.
Do not use this stool on wet or slippery oors as the base can slide out if the stool is
tilted and there isn’t sufcient friction with the oor.
If any component is not in proper working order or appears worn, contact UPLIFT
Desk immediately for repair or appropriate replacement parts.
If the UPLIFT Desk Motion Stool is not properly assembled, personal injury and dam-
age to the UPLIFT Desk Motion Stool could result.
Do not use solvents, abrasive cleaners, or scouring pads on any part of the UPLIFT
Desk Motion Stool.
This product’s maximum weight capacity is 300 lb, EVENLY DISTRIBUTED. DO NOT
exceed the maximum weight capacity.
To avoid falling or tipping, keep both feet at on the ground for balance.
UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Copyright Notice: This guide is a component of the UPLIFT Motion Stool. This guide is a part of the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT Desk website: upliftdesk.com.
Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©