V-TAC VT-767-2 User manual

In case of any query/issue with the product, please reach out to us at: [e-mail]
For More products range, inquiry please contact our distributor or nearest dealers.
V-TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul.L.Karavelow 9B
INSTRUCTION MANUAL
LED SOLAR WALL LIGHT
INTRODUCTION & WARRANTY
TECHNICAL DATA
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions
carefully before starting the installation and keep this manual handy for future reference. If you have any another
query, please contact our dealer or local vendor from whom you have purchased the product. They are trained
and ready to serve you at the best. The warranty is valid for 2 years from the date of purchase. The warranty
does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no
warranty against damage to any surface due to incorrect removal and installation of the product. The products
are suitable for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would void the warranty. This
product is warranted for manufacturing defects only.
MODEL VT-767-2
SKU 8276, 8277
LUMENS 220 Lm
POWER 1.5W
SOLAR PANEL 0.7Wp, Mono-Crystalline silicon
BATTERY Li-ion, 1200mAh, 3.7V
CHARGING TIME 6-7 Hours
WORKING TIME Maximum 24 Hours
WORKING MODE 2 Dierent Lighting modes
LED TYPE SMD
DETECTION ANGLE 90°
SENSOR RANGE 2-6 M
COLOR TEMPERATURE 4000K
DIMENSION 144.5x96x79mm
BODY TYPE ABS+PC
INSTALLATION HEIGHT 2-4 M
MULTI-LANGUAGE
MANUAL QR CODE
Please scan the QR code
to access the manual in
multiple languages.

This marking indicates that this
product should not be disposed of
with other household wastes.
WARNING
INSTALLATION INSTRUCTIONS
WORKING MODES
1. Please make sure to turn o the power before starting the installation.
2. Installation should be done by certified electrician.
. 3 The light source of this luminaire is not replaceable; when the light source reaches its
end of life the whole luminaire shall be replaced.
1. Use the card to measure hole position correctly and drill 2 holes.
2. Fix 2 expansion plugs into the holes.
3. Fix a screw to the lower expansion plug with a spare space, insert the notch onto the
screw.
4. Straighten the whole lamp and fasten the upper screw.
5. Press the button to adjust to demanded working mode.
Please press the button to adjust working mode.
• Press 1st time for MODE A
• Press 2nd time for MODE B
• Press 3rd time for OFF
1
23
4
5
1. Hole
2. Expansion Plug
3. Screw
4. Mounting Hole
5. Button

NOTICE
1. Install this light onto flat surface directionally to get enough solar.
2. The lamp will light up when the environmental brightness is less than 30lux.
3. Inside battery is replaceable, 18650 Li-ion battery, 1200mAh/3.7V.
4. Lamp need to be installed 2-4Mtr from the ground.
MAINTENANCE & WARNING
• Do not use solvents, petrol, etc. Otherwise the light will be damaged.
• Clean the light with a dry, lint-free cloth.
• Check the solar panel for dirt regularly. If dirt or is present remove it to guarantee
flawless function of the product.
• Especially during the winter, keep the product free from snow and ice.
• Confirm installation direction is correct (solar panel should be at top)
• Confirm no objects blocking the solar panel to receive sunlight
• Keep away from the fire.
• Don’t immerse in the water
Mode A: Automatically turns on to full
brightness (220lm) when motion
is detected in the range ≤6 mtrs and then
turns to weak brightness (front light on &
back light on) in 10 seconds of no motion.
Mode B: Automatically turns on to full
brightness (220lm) when motion is detected
in the range ≤6 mtrs and then turns to weak
brightness (front light o & back light on) in
10 seconds of no motion.