V-TAC VT-13 User manual

LED DOME LIGHT WITH PIR SENSOR
TECHNICAL DATA
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: [e-mail]
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS.
V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions care-
fully before starting the installation and keep this manual handy for future reference. If you have any another query,
please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready
to serve you at the best. The warranty is valid for 3 years from the date of purchase. The warranty does not apply to
damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage
to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily
operation. Usage of product for 24 Hours a day would void the warranty. This product is warranted for manufacturing
defects only.
• Can identify day and night: The consumer can adjust working state in dierent ambient light. It can work in the
daytime and at night when LUX knob is adjusted on the "sun" position (max). It can work in the ambient light less
than 3LUX when it is adjusted on the "moon" position (min). As for the adjustment pattern, please refer to the testing
pattern.
• Time-Delay is added continually: When it receives the second induction
signals within the first induction, it will restart to time from the moment.
• Time-Delay is adjustable. It can be set according to the consumer's
desire. The minimum time is 10sec+3sec. The maximum is 3min±30sec.
1. Please make sure to turn o the power before starting the installation.
2. The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire
should be replaced.
3. Installation must be performed by a qualified person.
4. For Indoor use only
INTRODUCTION & WARRANTY
WARNING
FUNCTION
MODEL
SKU
WATTS
LUMENS
AMBIENT LIGHT
TIME DELAY
INPUT VOLTAGE
DETECTION RANGE
DTECTION DISTANCE
BEAM ANGLE
LIFE SPAN
INSTALLING HEIGHT
PROTECTION RATING
DETECTION MOTION SPEED
VT-13
21807, 21808, 21809
12W
900 Lm (3000K)
1000 Lm (4000/6400K)
<3-2000 LUX (Adjustable)
Min. 10sec ±3sec
Max. 3min ±30sec
AC: 220-240V, 50/60Hz
360°
6m max (<24°C)
120°
25000 Hours
2-2.4 M
IP20
0.6-1.5 m/s
INSTRUCTION MANUAL

• Switch o the power
• Remove the cover of the luminaire. (Refer to figure 1)
• Find the wire hole in the bottom and pass the power wire through hole. Connect the power wire into connection-wire
column according to the connection-wire diagram.
• Fix the bottom with inflated screw on the selected position.
• Switch of the power and test it
• Turn the Time knob anti-clockwise on the minimum. Turn the TIME knob clockwise on the maximum (sun).
• Switch on the power; the lamp will have no signal at the beginning. Aer Warm-up 30sec, the lamp will start to
work. If it recceives the induction siganl, the lamp will turn on. While there is no another induction signal any more,
the lamp should stop working within 10sec+3sec.
• Turn LUX knob anti-clockwise on the minimum (moon). If the ambient light is more than 3LUX, the lamp should not
work. If the ambient light is less than 3LUX (darkness), the sensor would work. Under no induction signal condition,
the lamp should stop working winthin 10sec+3sec.
• Should be installed by qualified electrician.
• Before installing please make sure the power is OFF to avoid electric shock.
• Avoid installing it on uneven surface.
• Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors etc.
• Avoid mounting the detector near heat sources, such as heating vents, air conditioning units etc.
• Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall plants
NOTE: When testing in daylight, please turn LUX knob to (SUN) position, otherwise the sensor lamp could not work!
INSTALLATION DIAGRAM
TEST
WIRING DIAGRAM
Figure 1 Figure 2
This marking indicates that this
product should not be disposed of
with other household wastes.
Caution, risk of electric shock.

WICHTIGE HINWEISE:
• Elektro- und Elektronikgeräte, die zu Abfall geworden sind, werden als Altgeräte bezeichnet.
Altgeräte dürfen nicht mit anderem Hausmüll entsorgt werden.
• Besitzer von Altgeräten am Ende der Nutzungsdauer müssen das Gerät bei den von den
öffentlichen Entsorgungsträgern oder Händlern eingerichteten Sammelstellen zurückgeben.
Diese Rücksendung ist für Sie mit keinen Kosten verbunden.
• Besitzer von Altgeräten sind verpflichtet, Lampen vor der Rückgabe zerstörungsfrei aus dem
Altgerät zu entfernen.
• Das Symbol „Gekreuzte Mülltonnen“ weist darauf hin, dass dieses Produkt nicht mit dem
anderen Hausmüll entsorgt werden darf und am Ende seiner Lebensdauer vom unsortierten
Hausmüll getrennt gesammelt werden muss.
• Bei der Entsorgung von Elektrogeräten auf Deponien oder Halden können Schadstoffe ins
Grundwasser gelangen und in die Nahrungskette gelangen und Ihre Gesundheit und Ihr
Wohlbefinden schädigen.
• Unter folgendem Link gelangen Sie zum Online-Verzeichnis der Sammel- und Rückgabestel-
len: https://www.ear-system.de/ear-verzeichnis/sammel-und-ruecknahmestellen