Velleman HAM202 User manual

HAM202
PIR home alarm system with camera and wireless remote
PIR-alarm met camera en draadloze afstandsbediening
Alarme PIR avec caméra et télécommande sans fil
Sistema de alarma PIR con cámara y mando a distancia
PIR-Alarmanlage mit Kamera und Funk-Fernbedienung
Sistema de alarme PIR para habitações com câmara e
controlo remoto sem fios
USER MANUAL 6
GEBRUIKERSHANDLEIDING 12
MODE D'EMPLOI 19
MANUAL DEL USUARIO 25
BEDIENUNGSANLEITUNG 31
MANUAL DO UTILIZADOR 38

HAM202
V. 03 –11/12/2014 2 ©Velleman nv

HAM202
V. 03 –11/12/2014 3 ©Velleman nv

HAM202
V. 03 –11/12/2014 4 ©Velleman nv

HAM202
V. 03 –11/12/2014 5 ©Velleman nv

HAM202
V. 03 –11/12/2014 6 ©Velleman nv
USER MANUAL
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that
disposal of the device after its lifecycle could harm the
environment. Do not dispose of the unit (or batteries) as
unsorted municipal waste; it should be taken to a
specialized company for recycling. This device should be
returned to your distributor or to a local recycling service. Respect
the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly
before bringing this device into service. If the device was damaged in
transit, don't install or use it and contact your dealer.

HAM202
V. 03 –11/12/2014 7 ©Velleman nv
2. Safety Instructions
Keep this device away from children and unauthorised
users.
Indoor use only. Keep this device away from rain,
moisture, splashing and dripping liquids.
3. General Guidelines
Refer to the Velleman® Service and Quality Warranty on the last
pages of this manual.
This system can provide valuable protection for your home and
property if used properly. However, it cannot guarantee complete
protection against burglary or robbery. Therefore, Velleman nv will
not be responsible for any losses or damages which occur during
the use of this product.
Keep this device away from dust and extreme temperatures.
Protect this device from shocks and abuse. Avoid brute force when
operating the device.
Do not aim the camera at the sun or other extremely bright
objects.
Familiarise yourself with the functions of the device before actually
using it.
All modifications of the device are forbidden for safety reasons.
Damage caused by user modifications to the device is not covered
by the warranty.
Only use the device for its intended purpose. Using the device in
an unauthorised way will void the warranty.
Damage caused by disregard of certain guidelines in this manual
is not covered by the warranty and the dealer will not accept
responsibility for any ensuing defects or problems.
There are no user-serviceable parts inside the device except for
the batteries. Refer to an authorized dealer for service and/or
spare parts.
Do not use this product to violate privacy laws or perform illegal
activities. Respect the legislation in your region when installing an
alarm system. If necessary, refer to local authorities.

HAM202
V. 03 –11/12/2014 8 ©Velleman nv
4. Features
This basic home alarm system has an integrated PIR sensor and
camera. The PIR sensor detects if an intruder enters the room and
the camera starts recording video files. An infrared remote allows
you to arm and disarm the alarm system. A solar panel provides
power during standby. The battery power is only used during an
alarm trigger and video recording.
alarm trigger: motion detection via PIR sensor
remote control to arm and disarm the alarm system
camera: record video files after a PIR trigger
solar panel to extend battery lifetime
130 dB alarm sound
mute mode: the alarm sound can be disabled
quick and easy installation.
5. Overview
Refer to the illustrations on page 2 of this manual.
alarm system with camera
1
solar panel
6
siren
2
IR LEDs for night vision
7
USB port
3
camera
8
microSD card slot
4
indicator LED
9
delete/mute button
5
motion detector
10
battery compartment
remote control
11
IR LED
13
arm button (ARM)
12
indicator LED
14
disarm button (CLR)
6. Installation
6.1 Installing/Replacing Batteries
Refer to the illustrations on page 3–4 of this manual.
Warning! Do not puncture batteries or throw them in fire as
they may explode. Do not attempt to recharge non-
rechargeable batteries (alkaline). Dispose of batteries in
accordance with local regulations. Keep batteries away from
children.

HAM202
V. 03 –11/12/2014 9 ©Velleman nv
Caution! Remove the batteries from the devices if they will not be
used for a long time. Old batteries can begin to leak and damage the
device.
Alarm
When the red indicator LED [4] lights up continuously, the batteries
are low. In that case, replace the batteries immediately.
1. Remove the screw from the bottom of the alarm cover and take
off the cover [A].
2. Insert 3 identical 1.5 V AA batteries according to the polarity
markings inside the battery compartment.
When the last battery is inserted, the alarm beeps to indicate
that the batteries are installed correctly.
3. Place the cover back and fix it with the screw.
Caution! Each time you replace the batteries, you must reconnect
the alarm to the remote control.
Remote Control
1. Remove the screws from the back of the remote control and
take off the cover [B].
2. Insert 3 identical LR44 batteries according to the polarity
markings inside the battery compartment.
3. Place the cover back and fix it with the screws.
6.2 Connecting the Alarm and the Remote Control
After inserting batteries, point the remote control to the alarm and
push the ARM button [13] twice. The alarm's LED [4] lights up to
indicate that the connection between alarm and remote control is
established.
To clear a connection between an alarm and a remote control, take
out the batteries from the alarm. The connection is deleted
automatically.
Caution! Each time you replace the batteries, you must reconnect
the alarm to the remote control.
6.3 Installing a microSD Card
Refer to the illustrations on page 5 of this manual.
Note: it is recommended to use a formatted microSD card.
To install/remove a microSD card, proceed as follows:
1. Slide the card slot cover [8] as indicated [C] to unlock it.
2. Lift the cover [D].

HAM202
V. 03 –11/12/2014 10 ©Velleman nv
3. Insert a microSD card (not included) in the card slot [F].
4. Close the cover [G] and slide it as indicated [H] to lock it.
5. To remove the SD card, slide the card slot cover [8] as
indicated [I] to unlock it.
6. Lift the cover [J].
7. Take out the microSD card.
6.4 Setting the Date and Time
To set the date and time in the alarm (for a correct timestamp on the
recorded video files), connect the alarm to your pc via the USB
port [7] and the included USB cable. The alarm automatically copies
the date and time from your pc.
6.5 Installing the Alarm
You can use the alarm free-standing on a horizontal surface, or you
can attach it to a wall. To mount against a wall, proceed as follows:
1. Remove the back cover from the alarm and screw it to the wall
at 1.0–1.5 m above the ground [M].
2. Click the body of the alarm into place on the back cover and fix
it with the screw.
7. Operation
Arming and Disarming the Alarm
To arm the alarm, press the ARM button [13]on the remote
control. The alarm plays a confirmation tune to indicate that
arming is successful. Note that the alarm is only activated after a
delay of 30 seconds, to allow you to leave the area without
triggering the alarm.
When the alarm detects motion, the siren goes off and the camera
starts recording video after a delay of 5 seconds. These 5 seconds
allow you to enter the area again and disarm the alarm before it
goes off. For each motion detection, the camera records a
30 second video file.
To disarm the alarm, press the CLR button [14]on the remote
control.
Muting the Alarm
If you want to mute the siren, proceed as follows:
1. Press the CLR button to disarm the alarm.