Velleman K8093 User manual

ILLUSTRATED ASSEMBLY MANUAL H8093IP’1
K8093
Remote controlled
home alarm
��������������� ���������������������

Velleman N.V.
Legen Heirweg 33
9890 Gavere
(België)
��������������� ���������������������

Forum
Forum
Participate our Velleman Projects Forum
Subscribing our newsletter?, visit www.vellemanprojects.eu
��������������� ���������������������

assembly
hints 1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
• A good quality soldering iron (25-40W) with a small tip.
• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and
will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
• Thinraisin-coresolder.Donotuseanyuxorgrease.
• Adiagonalcuttertotrimexcesswires.Toavoidinjurywhencuttingexcessleads,holdtheleadsotheycannot
ytowardstheeyes.
• Needle nose pliers, for bending leads, or to hold components in place.
• SmallbladeandPhillipsscrewdrivers.Abasicrangeisne.
)For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
• Makesuretheskilllevelmatchesyourexperience,toavoiddisappointments.
• Follow the instructions carefully. Read and understand the entire step before you perform each operation.
• Perform the assembly in the correct order as stated in this manual
• Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
• Values on the circuit diagram are subject to changes, the values in this assembly guide are correct*
• Usethecheck-boxestomarkyourprogress.
• Please read the included information on safety and customer service
*Typographicalinaccuraciesexcluded.Alwayslookforpossiblelastminutemanualupdates,indicatedas‘NOTE’onaseparateleaet.
1.3 Soldering Hints :
1. Mount the component against the PCB surface and carefully solder the leads
2. Make sure the solder joints are cone-shaped and shiny
3. Trimexcessleadsascloseaspossibletothesolderjoint
- 5 -
- 4 -
DO NOT BLINDLY FOLLOW THE ORDER OF THE
COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR
VALUE ON THE PARTS LIST!
��������������� ���������������������

assembly
hints 1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
• A good quality soldering iron (25-40W) with a small tip.
• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and
will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
• Thinraisin-coresolder.Donotuseanyuxorgrease.
• Adiagonalcuttertotrimexcesswires.Toavoidinjurywhencuttingexcessleads,holdtheleadsotheycannot
ytowardstheeyes.
• Needle nose pliers, for bending leads, or to hold components in place.
• SmallbladeandPhillipsscrewdrivers.Abasicrangeisne.
)For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
• Makesuretheskilllevelmatchesyourexperience,toavoiddisappointments.
• Follow the instructions carefully. Read and understand the entire step before you perform each operation.
• Perform the assembly in the correct order as stated in this manual
• Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
• Values on the circuit diagram are subject to changes, the values in this assembly guide are correct*
• Usethecheck-boxestomarkyourprogress.
• Please read the included information on safety and customer service
*Typographicalinaccuraciesexcluded.Alwayslookforpossiblelastminutemanualupdates,indicatedas‘NOTE’onaseparateleaet.
1.3 Soldering Hints :
1. Mount the component against the PCB surface and carefully solder the leads
2. Make sure the solder joints are cone-shaped and shiny
3. Trimexcessleadsascloseaspossibletothesolderjoint
0.000
- 5 -
- 4 -
��������������� ���������������������

- 7 -
- 6 -
R1 : 47K (4 - 7 - 3 - B)
R2 : 560 (5 - 6 - 1 - B)
R3 : 560 (5 - 6 - 1 - B)
R4 : 47K (4 - 7 - 3 - B)
R5 : 560 (5 - 6 - 1 - B)
R6 : 1K (1 - 0 - 2 - B)
R7 : 10K (1 - 0 - 3 - B)
R8 : 10K (1 - 0 - 3 - B)
R9 : 2K2 (2 - 2 - 2 - B)
R10 : 560 (5 - 6 - 1 - B)
1
R...
R...
R...
I. CONSTRUCTION
2
features
• can store up to 4 remote controls (FIFO)
• chime function
• built-in pre-alarm
• always armed after power outage
• the built-in relay can switch a regular alarm (not included) (3 A 125 VAC) after 20 s pre-alarm
• arm time:
• slow with indication: if the door is open or closed (time to leave the room)
• quickly
• magnetic door contact included
Specications
• power supply: 12V DC
• consumption:
• armed: 20 mA
• alarm relay powered: 50 mA
• relay: 3 A - 125 VAC
• frequency: 433.92 MHz
• 32-bit code technology
• more than 1.000.000.000 unique codes
• code can easily be changed for safety purposes
• transmitter: R&TTE compliant (ETS 300-220) *
• openeldrangeofupto30mpossible
• external antenna wire
• receiver dimensions: 108 x 102 x 45 mm / 4.25 x 4 x 1.77"
* ETS 300 -220:only for EU countries
Compatible remotes (not included):
VM130T: 2-channel RF
remote control transmitter
VM166T: 2-channel
transmitter with LED light
��������������� ���������������������

- 7 -
- 6 -
Construction
R1 : 47K (4 - 7 - 3 - B)
R2 : 560 (5 - 6 - 1 - B)
R3 : 560 (5 - 6 - 1 - B)
R4 : 47K (4 - 7 - 3 - B)
R5 : 560 (5 - 6 - 1 - B)
R6 : 1K (1 - 0 - 2 - B)
R7 : 10K (1 - 0 - 3 - B)
R8 : 10K (1 - 0 - 3 - B)
R9 : 2K2 (2 - 2 - 2 - B)
R10 : 560 (5 - 6 - 1 - B)
Resistors
1
IC socket
4
R...
R...
R...
Ceramic Capacitors
3
C1 : 100nF (104)
C2 : 100nF (104)
C3 : 100nF (104)
IC1: 14p
c ...
c
...
Vertical diode
5
CATHODE
D...
CATHODE
D2 : 1N4007
Transistors
6
T1 : BC547
T2 : BC547
T3 : BC547
I. CONSTRUCTION
Diodes
D1 : 1N4148
D2 : 1N4148
2
Watch the
polarity!
Watch the
polarity!
TVoltage regulator
7
VR...VR...
VR1 : UA78L05
Push button
8
SW1:LEARN BUTTON
Watch the position of
the notch!
features
• can store up to 4 remote controls (FIFO)
• chime function
• built-in pre-alarm
• always armed after power outage
• the built-in relay can switch a regular alarm (not included) (3 A 125 VAC) after 20 s pre-alarm
• arm time:
• slow with indication: if the door is open or closed (time to leave the room)
• quickly
• magnetic door contact included
Specications
• power supply: 12V DC
• consumption:
• armed: 20 mA
• alarm relay powered: 50 mA
• relay: 3 A - 125 VAC
• frequency: 433.92 MHz
• 32-bit code technology
• more than 1.000.000.000 unique codes
• code can easily be changed for safety purposes
• transmitter: R&TTE compliant (ETS 300-220) *
• openeldrangeofupto30mpossible
• external antenna wire
• receiver dimensions: 108 x 102 x 45 mm / 4.25 x 4 x 1.77"
* ETS 300 -220:only for EU countries
��������������� ���������������������

- 8 - - 9 -
Construction
Sounder
9
+
BUZ1
BUZ1
BUZ1
Terminal blocks
10
SK2 : 2p (Relais)
SK3 : 2p (N.O. / N.C)
SK4 : 2p (COM / -)
SK5 : 2p (power supply)
Output
Electrolytic capacitors
11
Watch the polarity!
C4 : 470µF
C5 : 10µF
RF-receiver
12
RX1 : RX433N
Relay
13
LD1: Red (power)
LD2: Red (status)
LD3: Red (alarm)
LD4: Green (relais)
COM
NO NC
LED’s
14
STEP1: Place the LEDs together with the circuit board in the upper part
of the housing.
STEP2: Solder one lead of each led and check the positon. If OK,
solder the second lead.
R...
R...
R...
R...
R...
R...
R...
R...
R...
R...
R...
R...
R...
R...
STEP1 STEP2
C (-)
Watch the polarity!
15
IC1: VK8093
(programmed PIC16F1503-I/P)
16
R... R...
RY1
��������������� ���������������������

- 8 - - 9 -
Assembly
Relay
LED’s
R...
R...
R...
R...
R...
R...
R...
R...
R...
R...
R...
R...
R...
R...
STEP2
IC
15
Watch the position of
the notch!
IC1: VK8093
(programmed PIC16F1503-I/P)
Antenna
16
R... R...
R...
R...
R...
R...
R...
R...
R...
Home Alarm System with RF Remote
K8093
LEARN
TX 12V DC OUTPUT REED
NO NC COM
+
TOP
PCB
BOTTOM
SCREW
II. ASSEMBLY
��������������� ���������������������

- 10 - - 11 -
R...
R...
R...
R...
R...
R...
R...
Driver installation & programs
IV. ARMING THE UNIT
Out of the box no remotes are assigned for safety reasons. When the unit powers up it is always armed!
Unit is capable of storing 4 remotes, FIFO.
The stored remotes can be cleared from memory by holding the LEARN button while powering up, The unit will beep 10 times
(fast) to indicate the erasing process.
STATUS INDICATION (LD3)
LEARNING A REMOTE:
1. Press the “Learn”-button once, the status LED light continious. The unit is ready for learning a remote (there is a timeout!).
2. Hold the 2 buttons of the remote pressed. Release the buttons when the status LED turns off , the remote is learned.
REMOTE CONTROL:
1. DISARM
2. ARM
Power
supply
Relay
Door contact
GND*
(*) If you want to connect a 12V
siren directly to the relay you can
connect the +12V of the input volt-
age to the COM. Connect the nega-
tive lead of the siren to the leftmost
(-) connector and the positive to
the NC or NO contact of the relay.
III.CONNECTION DIAGRAM
���������������� ���������������������