Verizon GT704WG User manual

Wireless
DSL Gateway
User’s
Manual
GT704WG

Table of Contents
1 Introduction 1
Minimum System Requirements 1
Features 2
Getting to Know the Gateway 3
2 Performing a Quick Setup 7
Accessing Quick Setup Screens 7
Changing the Password 10
3 Viewing the Gateway’s Status 13
Broadband Connection Status 13
Network Status 16
4 Configuring Wireless Settings 17
Accessing Wireless Setup 17
Basic Wireless Setup 20
Wireless Advanced Settings 20
Wireless Status 25
5 Configuring Advanced Settings 27
Accessing Advanced Setup Screens 27
DSL Settings 30
DHCP Settings 30
LAN IP Address 32
WAN IP Address 33
QoS Settings Upstream 35
QoS Settings Downstream 38
QoS Status 39
Remote Management/Telnet 39
Telnet Timeout Setting 40
Dynamic Routing 41
Static Routing 41
UPnP (Universal Plug and Play) 42
USB Port Detection 42
Time Zone 43
Remote Syslog Capture 43
i

ii
Wireless DSL Gateway User Manual
iii
Table of Contents
ii
6 Configuring Security Settings 45
Accessing Wired Security Screens 45
Admin User Name and Password 46
Firewall 47
Applications 50
DMZ Hosting 51
NAT (Network Address Translation) 52
Port Mapping 52
7 Configuring Parental Controls 53
Accessing Parental Control Screens 53
Services Blocking 54
Website Blocking 55
Schedule Rules 56
8 Configuring the Gateway’s Utilities 59
Accessing the Utilities Screens 59
Restore Default Settings 61
Upgrade Firmware 61
Multiple PVC 62
Web Activity Log 62
System Log 63
OAM Ping Test 64
Ping Test 65
Reboot 65
9 Troubleshooting 67
Troubleshooting 67
Frequently Asked Questions 69
A Reference 75
Locating Computer Information 75
Locating Windows Operating System Files 76
B Switching to Static IP on the Computer 79
Windows 98 SE 79
Windows Me 82
Windows 2000 85
Windows XP 89
C Computer Security 93
Comparing DSL Service with a Dial-Up Modem 93
Gateway Security 94
Computer Security 94
Electronic Security 95

ii
Wireless DSL Gateway User Manual
iii
Table of Contents
D Specifications 97
General 97
Wireless Operating Range 98
LED Indicators 98
Environmental 98
E Glossary 99
F Service Acronyms 103
Service Acronym Definitions 103

iv
Wireless DSL Gateway User Manual
This page left intentionally blank.

1
Introduction
Thank you for purchasing the Wireless DSL Gateway. The Gateway is the simplest
way to connect computers to a high-speed broadband connection. This easy-to-use
product is perfect for the home office or small business. If you want to take your
computing to the next level, the Wireless DSL Gateway is sure to be one of the keys
to your success.
Minimum System Requirements
s Active DSL service
s Computer with an 10 Mbps or 10/100 Mbps Ethernet connection, or USB
connection
s Microsoft Windows 98 Second Edition (SE), Millennium Edition (Me), NT 4.0,
2000, XP, Vista
Mac OS 7.1+, 8.0+, 9.0+, OS X+
☞ Note: USB LAN port is not supported with Microsoft Windows
NT 4.0, Windows Vista 64-bit, or Mac OS.
s Internet Explorer 4.0 or higher (5.x+ recommended) or Netscape Navigator
4.0 or higher (4.7+ recommended)
s TCP/IP network protocol installed on each computer
1

2
Wireless DSL Gateway User Manual
3
Chapter 1 Introduction
Features
s Plug-and-Play installation support for computers running Windows oper-
ating systems (98SE, Me, 2000, XP, and Vista)
s ADSL WAN port (RJ-11)
s Full-rate ANSI T1.413 Issue 2, ITU G.992.1(G.dmt) and G.992.2(G.lite)
standard compliance
s Auto-handshake for different ADSL flavors
s USB 1.1 device specification compliance
s 12 Mbps USB data rate (full speed) support
s Bridged Ethernet over ATM, PPP over ATM, PPP over Ethernet
s Precise ATM traffic shaping
s IP packet routing and transparent bridge
s RIP-1, RIP-2, and static routing protocol support
s Built-in NAT, DHCP server
s DNS relay support
s PAP/CHAP authentication, administrative passwords through Telnet
s 64-, 128-, and 256-bit WEP/WPA wireless LAN security
s IEEE 802.3 Ethernet standard compliance
s 10/100 Base-T Ethernet ports (4)
s Fast Ethernet flow control support
s Web-based configuration setup
s FTP firmware upgradeable
s Web download support
s 802.11b/g support

2
Wireless DSL Gateway User Manual
3
Chapter 1 Introduction
Getting to Know the Gateway
This section contains a quick description of the Gateway’s lights, ports, etc.
The Gateway has several indicator lights (LEDs) on its front panel and a series of
ports on its rear panel.
Front Panel
The front panel of the Gateway features nine lights: Power, DSL, Internet,
Ethernet (4), USB, and Wireless.
Power
DSL Internet
Ethernet
1Wireless
234USB
1234
Power Light
The Power light displays the Gateway’s current status. If the Power light glows
steadily green, the Gateway is receiving power and fully operational. When the
Power light is rapidly flashing, the Gateway is initializing. If the Power light is
glows red when the Power cord is plugged in, the Gateway has suffered a critical
error and technical support should be contacted.
DSL Light
The DSL light illuminates when the Gateway is connected to a DSL line.
Internet Light
When the Internet light glows steadily, the Gateway is connected to the DSL
provider. When it flashes, the Gateway’s built-in DSL modem is training for the
DSL service.

4
Wireless DSL Gateway User Manual
5
Chapter 1 Introduction
Ethernet Lights
The Ethernet lights illuminate when the Gateway is connected to one or more of
its yellow Ethernet ports.
USB Light
The USB light illuminates when the Gateway is connected via its USB port.
Wireless Light
The Wireless light illuminates when the Gateway is connected wirelessly (if the
Gateway’s Wireless feature is turned on).
Rear Panel
The rear panel of the Gateway contains seven ports (Ethernet [4], Phone, USB, and
Power), as well as Reset and Power switches.
12VDC 0.6A
421
ON/OFF
Ethernet Cable
(from Ethernet port [1-4]
to computer)
USB Cable
(from USB port
to computer)
Power Adapter
(from Power port
to power outlet)
DSL Cable
(from DSL port
to phone jack)
Ethernet Ports
The Ethernet ports are used to connect computers to the Gateway via Ethernet
cable. The Ethernet ports are 10/100 Mbps auto-sensing ports, and either a
straight-through or crossover Ethernet cable can be used when connecting to
the ports.

4
Wireless DSL Gateway User Manual
5
Chapter 1 Introduction
DSL Port
The DSL port is used to connect the Gateway to a DSL (Digital Subcriber Line)
connection.
Reset Switch
Depressing the Reset switch for one second will restore the Gateway’s factory
default settings. To reset the Gateway, depress and hold the Reset switch for
approximately one second. The reset process will start after releasing the switch.
USB Port
The USB port is used to connect a computer to the Gateway via USB cable.
Power Port
The Power port is used to connect the Power cord to the Gateway.
N Warning: Do not unplug the Power cord from the Gateway
during the reset process. Doing so may result in permanent
damage to the Gateway.
Power Switch
The Power switch is used to power the Gateway on and off.

6
Wireless DSL Gateway User Manual
This page left intentionally blank.

7
Performing a
Quick Setup
This chapter is a guide through a quick set up of the Gateway, including how to
connect the Gateway to the ISP.
To complete the quick setup, have the Welcome Letter or ISP Worksheet handy. If
the document is not available, contact the ISP immediately.
Accessing Quick Setup Screens
To access the Quick Setup screens:
1. Open a Web browser. In the “Address” text box, type:
http://192.168.1.1
then press Enter on the keyboard.
2

8
Wireless DSL Gateway User Manual
9
Chapter 2 Performing a Quick Setup
2. The “Home” screen appears. Click Quick Setup.
3. A login window appears. Enter the user name and password in the appropri-
ate text boxes, then click OK.
☞ Note: The default user name is “admin.” The default password is
“password.”

8
Wireless DSL Gateway User Manual
9
Chapter 2 Performing a Quick Setup
4. Follow the instructions in the “Welcome to the Quick Setup” screen, then click Next.
5. At the top of the next window, select PPPoE or DHCP.
5a. If PPPoE was selected in step 5, the default user name and password are
entered in the appropriate text boxes.
If “DHCP” was selected, go to step 6.
5b. If PPPoE was selected in step 5, select the IP type (“Dynamic IP-DHCP
[Default]” or “Single Static IP Address”). If Single Static IP Address was select-
ed, enter the address in the appropriate text box.
6. Optional - Select the DNS type (“Dynamic DNS Addresses [Default]” or
“Static DNS Addresses”). If Static DNS Addresses was selected, enter the prima-
ry and secondary DNS addresses in the appropriate text boxes. If unsure what
to enter in this section, contact the ISP.

10
Wireless DSL Gateway User Manual
11
Chapter 2 Performing a Quick Setup
7. Click Apply at the bottom of the screen.
8. Read the instructions on the next screen. The Gateway is successfully
configured.
The Power light flashes rapidly while the Gateway restarts, then glows steadily
green when fully operational. The Internet light will also glow steadily green. The
Gateway is now configured and users can start surfing the Internet.
If an error appears, stating the Web browser was unable to connect to the Internet,
check the configuration settings. Ensure all the information required by the ISP is
entered correctly.
Changing the Password
To create or change the password allowing access to the Gateway’s Web
Configuration screens, follow these instructions:
1. From the “Home” screen, select Security.
2. The “Security” screen appears. Select “Admin User Name and Password.”

10
Wireless DSL Gateway User Manual
11
Chapter 2 Performing a Quick Setup
3. The “Change Admin Username/Password” screen appears. Enter a new
Username in the “Admin User Name” text boxt, then enter a new password in
the “Admin Password” text box. Make sure to write down the user name and
password and keep it in a secure location. They will be needed to access the
Gateway’s Web Configuration screens in the future.
4. Click Apply at the bottom of the screen.
5. Read the instructions on the next screen. The user name and password are
successfully changed.
Once the Gateway has rebooted, the new user name and password are active. To
access the Gateway’s Web Configuration screens, the new user name and password
must be entered.

12
Wireless DSL Gateway User Manual
This page left intentionally blank.

13
Viewing the
Gateway’s Status
After configuring the Gateway, the Gateway’s connection and network status can
be viewed. The Internet connection status is viewed in the “Broadband Connection
Status” screen, while the network status is viewed in the “My Network” screen.
Broadband Connection Status
To view the Gateway’s connection statistics, select Status in the Home screen. The
“Broadband Connection Status” screen appears. There are three sections in this
screen: General Statistics, PPP Status, and DSL Status.
☞
Note: No settings (other than connecting or disconnecting from
the Internet by clicking on Connect or Disconnect) can be
changed from the Broadband Connection Status screen.
General Statistics
The top section of the Broadband Connection Status screen displays general statis-
tics regarding the Gateway, including model number, firmware version, IP address,
and gateway IP address.
3

14
Wireless DSL Gateway User Manual
15
Chapter 3 Viewing the Gateway’s Status
PPP Status
The middle section of the Broadband Connection Status screen displays the status
of the Gateway’s PPP connection, including user name, authentication failures,
and packets sent and received.
DSL Status
The bottom section of the Broadband Connection Status screen displays the status
of the Gateway’s DSL connection, including mode settings, connection status, and
number of discarded packets. Click Reset to refresh all statistics on this screen

14
Wireless DSL Gateway User Manual
15
Chapter 3 Viewing the Gateway’s Status
In the menu on the left side of the Broadband Connection Status screen, there are
two other options available to view: NAT Table and Routing Table. Click to gen-
erate the option of choice.
NAT Table
Selecting NAT Table generates the “NAT Table” screen. This screen displays an overview
of the current list of open connections through NAT (Network Address Translation) the
Gateway supports between the networked computers and the Internet.
Routing Table
Selecting Routing Table generates the “Routing Table” screen. This screen displays
the an overview of the Gateway’s network routes.