Verizon LV5KIHP User manual

i
5G Internet Gateway
User Guide

ii
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/ TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
RF Exposure Statement
To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter
must be installed to provide a separation distance of at least 20cm from all persons (indoor), at
least 54cm from all persons (outdoor), and must not be co-located or operating in conjunction
with any other antenna or transmitter.

iii
Important Notice
The user is responsible for determining whether surfaces and installation environment is
appropriate. Please remember that many factors influence installation safety. Please follow the
user manual. Materials, flatness, cleanliness of surfaces, humidity, wind speed, time and many
other factors can affect the adhesion and fixedness of this product. Verizon does not guarantee
the product can be fixed and will not fall. Given the variety of factors that can affect the adhesion
and fixedness, it is essential that the user evaluates the conditions of surfaces and the
environment to determine whether they are suitable for installation.
DISCLAIMER
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, VERIZON MAKES NO OTHER
WARRANTIES, EITHER EXPRESS, IMPLIED OR STATUTORY. VERIZON DISCLAIMS ANY
LIABILITY CAUSED BY ANY USER’S NON-COMPLIANCE WITH THE USER MANUAL.
Safety Warnings
Adapter
Do not use any other power adaptor except the one that accompanies this unit or a power
adaptor identified in the list below.
Use of another adapter could result in damage to the unit.
The following power adaptor is qualified for use with this Verizon 5G Internet Gateway:
This unit must be powered by Delta Electronics, model ADP-120VH DD or equivalent UL listed
power source rated @ output 20Vdc, Maximum 6A.
Caution
Ensure to connect the power cord of power adapter to a socket-outlet with grounding
connection.

1
Chapter 1
Introduction
Verizon’s 5G Internet Gateway provides Verizon customers with an improved solution for 5G
home service. The innovative design of the 5G Internet Gateway allows customers to connect
their favorite devices to Verizon’s 5G Network.
Unboxing Information
Inside the product package for the 5G Internet Gateway, you should find the following items:
• 5G Internet Gateway × 1
• Bracket × 1
• Power adaptor ×1
• AC power cable × 1
• Cable clip (S) × 3
• Cable clip (L) × 1
• Cable tie × 1
• Gecko tape plate × 1
• Window wedge × 1
• Window wipe × 2
• Screw bag × 1

2
Bottom and Side Panel
Part
Description
LED
The LED light
s up in different ways to indicate the connectivity status of
the 5G
Internet Gateway.
Multipurpose
pair
button
Press this button once to connect the
5G Internet Gateway to Wi-Fi
Extender or Wi
-Fi Extender Mini devices via WPS or Bluetooth®. After the
pairing is successful,
the LED light will stop blinking blue.
RJ45
port
Connect the
5G Internet Gateway to PC or switch via an Ethernet cable.
DC jack
Connect the
power adaptor to the DC jack to provide power to the 5G
Internet Gateway from an electrical outlet.
Reset pin hole
Factor reset the device by press
ing the pin hole for 5 seconds.
Multipurpose pair
button
RJ45 Ethernet port
DC jack
Bottom panel
Side panel
●LED
Bracket
Reset pin hole
Gecko tape plate

3
LED and Audio Behavior
Status Front LED Sound
Device is booting up
Soft Fade in-out White
Not Applicable
WPS and Bluetooth®pairing mode
(Manual option)
Single press the multifunction pair button
to establish connection
Not Applicable
WPS/Bluetooth®is paired
Blue blinking ceases
Click sound
Plays once immediately
after establishing
connection
Activation completed
Device successfully connected to LTE, is
activated and will start searching for 5G
signal
Click sound
Plays once immediately
after activation
No 5G signal
Device cannot detect 5G signal
immediately after activation
Error sound
Plays once immediately
after switching to
operational mode
Poor 5G signal
5G signal is detected after activation but
signal strength is not strong enough.
Error sound
Plays once immediately
after switching to
operational mode
Passing 5G signal
Good 5G signal has been detected for
installation.
Good signal sound
Plays once immediately
after switching to
operational mode and
finding passing signal
Firmware update/Factory reset in
progress
Not Applicable

4
Error (Fault)
Hardware or software issue
Error sound
Plays once immediately
after incident
Working as advertised
Device setup is completed and Internet
is active. Show solid white light and then
dims to 50% brightness after 60
seconds.
Not Applicable
Wi-Fi is disabled
Amber blinking ceases until Wi-Fi is
enabled.
Not Applicable

5
Chapter 2
Self-Setup and Activation
Installation, Activation, and Setup
Please download the My Verizon Mobile app for installation, activation and setup of your 5G
Internet Gateway. Take out the set up guide print from the gift box.
Back side
This side should be printed with URL/QR code
Front side
Please do not remove anything from the box yet.
Scan the QR code to visit the URL on your mobile device or access
http://setup.verizon.com/5Ginternetgateway

6
When installing the 5G Internet Gateway, make sure that the back side of the device faces
towards the direction of the 5G signal.
Back side:
This side should face the 5G signal
Front side:
This side should face inside the home.
Operational Communication Signal

7
WPS Connection
WPS can be used to pair your 5G Internet Gateway to the Wi-Fi Extender or Extender Mini by
following these steps:
1. Short press the Multipurpose pair button on your 5G Internet Gateway.
2. Short press the Multipurpose pair button on the Wi-Fi Extender or Extender Mini, making
sure the device is within range of the 5G Internet Gateway.
3. The 5G Internet Gateway will play a sound to indicate pairing success.

8
Chapter 3
Accessing the Web User Interface
Login
After connecting and turning on the 5G Internet Gateway, a Sign In screen will appear.
Enter your admin password to log into the Home Page of the 5G Internet Gateway’s Web GUI. If
you forget your password, you can answer one of the security questions to reset the password to
factory default settings.
You can find the default password on the label under the 5G Internet Gateway.

9
Home Page/Main Section
After logging in, the Home Page of the 5G Internet Gateway will appear.
The Home Page is where users can check the connection status between the 5G Internet
Gateway and the Internet/mesh network, conduct network speed tests, and adjust settings such
as Wi-Fi options, parental controls, and more. In the upper right panel of the screen, the Network
Map presents a list of devices that are currently connected to the 5G Internet Gateway. Below
that, the screen is divided into three columns: Wi-Fi on the left, System Settings in the middle,
and Parental Controls and Help on the right.
The drop-down menu on the upper right of the Home Page includes selections such as Admin
Settings, My Verizon, Restart 5G Internet Gateway, and Sign Out.

10
3.2.1 Network Map (Speed test, Mesh network)
The Network Map is located in the upper-right section of the Home Page. The lines between the
5G Internet Gateway and the Internet/mesh network/devices on the map indicate the connection
status between them. A solid green line indicates a wired connection, a dashed line indicates a
Wi-Fi connection, and a gray line with a red x in the middle indicates that there is no connection.
To test the connection speed between the 5G Internet Gateway and the Internet/other networks,
click the “Test Speed” button on the lower left of the Network Map.
The number of APs and clients currently connected to the network are indicated in the lower
right section of the Network Map.
3.2.2 Admin Settings
The Change Admin Password section enables you to change the Admin password that is used to
sign in to the 5G Internet Gateway’s Home Page. Type the desired admin password in the New
Admin Password field, then type the admin password again in the Confirm Password field. Click
Change Password to apply the new password.
If the password you enter contains three consecutive or repeating alphanumeric characters, a
window will pop up as a warning of insufficient password strength.

11
In the Security Questions section, you can choose three security questions, then enter the
answer for each question. If a user forgets his/her admin password, one of the questions will be
used to revert the admin password to factory default settings. Click Save to save your changes.
Click Close to close the Admin Settings window.
3.2.3 My Verizon
You will be directed to My Verizon, where you can manage your account online. With My Verizon,
you can also pay your bill, check your usage and view your order status.
3.2.4 Restarting the 5G Internet Gateway
To restart the 5G Internet Gateway, click the drop-down arrow and select Restart 5G Internet
Gateway. A window will appear on the screen. Click Restart to restart the 5G Internet Gateway.
3.2.5 Sign Out
Click Sign Out to log off the 5G Internet Gateway.

12
Wi-Fi Settings
Click the > arrow on the bottom-right side of the Wi-Fi column in the Home Page to bring up the
Wi-Fi page. On this page, you can adjust settings for the Primary Wi-Fi Network, Guest Wi-Fi
Network, Wi-Fi Advanced Settings, and WPS.
3.3.1 Primary Wi-Fi Network
Slide the Enable switch to the right to activate the Primary Wi-Fi network. The switch will turn
blue to indicate that the selected Wi-Fi network is turned on. To turn off the Primary Wi-Fi
network, slide the switch to the left.

13
1. Wi-Fi name (SSID)
The Wi-Fi name (SSID) is the name of the wireless network broadcasting from the 5G Internet
Gateway. In order for devices to connect to the local network over a wireless link, they must
select this network name from the list of detected wireless networks in the area.
2. Password
Specify a password for your wireless network. Click the icon to display the selected
password for the SSID.
3. New Password
Enter a new password here for the SSID.
4. Confirm Password
Type your new password here.
Note: Passwords must be 8–63 characters long and are case sensitive. Changing your Wi-Fi
name or password may cause devices to lose their connection to the primary network.
5. Broadcast Wi-Fi Name (SSID)
Check this box if you want to broadcast your SSID. The SSID will be displayed when you search
for available networks.
6. Wi-Fi network encryption

14
Select one security method from the drop-down menu. The encryption types include None, WEP-
64, WPA2-Personal, and WPA-WPA2-Personal.
3.3.2 Guest Wi-Fi Network
Slide the Enable switch to the right to activate the Guest Wi-Fi network. The switch will turn blue
when the guest network is enabled. To turn off the Guest Wi-Fi network, slide the switch to the
left.
7. Wi-Fi name (SSID)
The Wi-Fi name (SSID) is the name of the wireless network broadcasting from the 5G Internet
Gateway. In order for devices to connect to the local network over a wireless link, they must
select this network name from the list of detected wireless networks in the area.
8. Password
Specify a password for your wireless network. Click the icon to display the selected
password for the SSID.
9. New Password
Enter a new password here for the SSID.
10. Confirm Password
Retype the new password here.

15
Note: Passwords must be 8–63 characters long and are case sensitive. Changing your Wi-Fi
name or password may cause devices to lose their connection to the primary network.
11. Broadcast Wi-Fi Name (SSID)
Check the box if you want to broadcast the SSID. The SSID will be displayed when you search for
available networks.
12. Wi-Fi network encryption
Select one security method from the drop-down menu. The encryption types include None, WEP-
64, WPA2-Personal, and WPA-WPA2-Personal.
3.3.3 Wi-Fi Advanced Settings
13. Wi-Fi Network Operation Mode
On this page, you may adjust the operation mode, channel, and bandwidth for the 5 GHz and 2.4
GHz primary Wi-Fi networks as well as adjust airtime allocation.
Slide the Enable switch that corresponds to either the 5GHz Wi-Fi Network or the 2.4GHz Wi-Fi
Network to the right to activate this function. The switch will turn blue when the respective Wi-Fi
network is enabled. To disable the Wi-Fi network, slide the switch to the left.
The options provided for the 5 GHz primary Wi-Fi network include:

16
802.11n only
802.11ac and 802.11n
802.11ax, 802.11ac and 802.11n
The options for the 2.4 GHz primary Wi-Fi network include:
802.11n and 802.11g
802.11ax, 802.11n and 802.11g
14. Airtime Allocation
Slide the Enable switch to the right to activate this function. The switch will turn blue when
airtime allocation is enabled. To disable airtime allocation, slide the switch to the left.
When ATF is enabled, the system needs to be restarted for it to take effect.
In the Airtime Allocation Policy pull-down menu, two policy options are available: Fair and Strict.
Use the slider below the Airtime Allocation Policy pull-down menu to adjust the percentage of
resources allocated to the primary and guest Wi-Fi networks. Sliding the bar to the right
increases the allocation percentage for the primary Wi-Fi network, while sliding the bar to the left
increases the allocation percentage for the guest Wi-Fi network. The allocation percentages for
the primary and guest Wi-Fi networks are shown in the two fields on the bottom of the page, and
change in real-time when the slider is adjusted.

17
15. PMF
Slide the switch to the right to enable PMF (protected management frames) on your 5G
Internet Gateway.
3.3.4 WPS
16. Primary Wi-Fi WPS
WPS allows rapid wireless connection between the 5G Internet Gateway and other WPS-
compatible devices. You can trigger the WPS function on Primary Wi-Fi by clicking on the
Primary Wi-Fi WPS button.